• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1226-1228
• /
• 2004

A novel lossless passive snubber is proposed for soft switching the boost type converters. The proposed snubber does not use any auxiliary switches. but uses two identical snubber capacitors which are charged in parallel at turn off of the main switch and discharged in series at turn on automatically, and the discharged energy is recovered effectively (more than $95[\%]$ recovery) into the output capacitor. Thus, the snubber provides zero voltage switching for the converter main switch, reducing both the turn off losses and the electromagnetic interference(EMI) noise, whitch improves the converter performance. The experimental results of a 20[kHz] 600[W] DC-DC boost converter and a single-phase AC-DC boost rectifier with the new snubber are presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.410-413
• /
• 2001

In this paper, we present results of this that design of the multi-layer VCO(Voltage Controlled Oscillator), which is composed of the resonation circuit and the oscillation circuit, using EM simulator and nonlinear RF circuit simulator. EM simulator is used for acquiring EM(Electromagnetic) characteristics of conductor pattern as well as designing multi-layer VCO, Acquired EM characteristics of the circuit pattern was used like real components at nonlinear RF circuit simulator. Finally VCO is simulated at nonlinear RF circuit simulator. The material for the circuit pattern was Ag and the dielectric was Dupont ＃9599, which is applied for LTCC process. The structure is constructed with 4 conducting layer. Simulated results showed that the output level was about 1[dBm], the phase noise was 102 [dBc/Hz] at 30[kHz] offset frequency, the harmonics -8dBc, and the control voltage sensitivity of 30[MHz/V] with a DC current consumption of 10[mA].

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.9-11
• /
• 2002

These days, electromagnetic radiation noise and switching losses of static converter become harmful. Many resonant inverters with radiation techniques solve their such problems. Auxiliary Resonant Commutated Pole Inverter (ARCP) was proposed. but it has two demerits. In circuit configuration. It isn't constructed by 2 in 1 IGBT modules, Besides, control is complicated because of neutral point voltage control and boost. current control. This paper proposes a new auxiliary resonant inverter which solved two demerits. In addition, it deals efficiency which compared with hard switching inverter and result of separation of power loss

• Journal of Power Electronics
• /
• v.11 no.5
• /
• pp.767-777
• /
• 2011

Power electronic systems such as switching power supplies are accounted as noise sources for other sensitive circuits. EMI caused by power converters can disturb the normal operation of the converter and other adjacent systems. Major research is concentrated on EMI mitigation for power converters in which the main concern is compliance with EMC standards to ensure proper operation of converters and nearby systems. This paper reviews EMI reduction techniques related to switching power converters with emphasis on the conducted EMI. A comprehensive review of significant research works is performed and various methods are thoroughly discussed and compared. Also, a classification of methods is presented. Moreover, converter prototypes are realized which contain several EMI mitigation techniques and their effects are presented via experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.106-108
• /
• 2002

SMPS는 스위칭을 통해 전력을 변환하므로 높은 dv/dt 및 di/dt 특성을 갖게 된다. 이러한 스위칭특성으로 인해 발생하는 EMI (Electromagnetic Interference) 노이즈는 기기 내부 또는 외부에 간섭을 일으킨다. 미국의 FCC (Federal Communications Commission) 및 유럽 의 CISPR(International Special Committee on Radio Interference) 등의 규정을 만족시키기 위해서 전도성 노이즈에 대한 충분한 이해와 해석이 필요하다. 본 연구는 SMPS에서의 EMI/EMC 대책 구현에 앞서, 전도성노이즈의 기본개념 및 발생/결합 경로를 분석하고 실제로 노이즈를 측정한다. 측정을 위해 Boost 컨버터가 제작/사용된다.

• Proceedings of the KIEE Conference
• /
• 2004.05b
• /
• pp.136-139
• /
• 2004

It is widely known that the ultra high frequency (UHF) method that detects the electromagnetic wave of the PD pulses in the gas insulated space is one of the most competitive methods for its high sensitivity. From the above point of view, this paper describes the propagation characteristics of GIS PD signals measured with ultra wide band (UWB) GIS PD detecting system in which PD signals are detected into the dual UHF band. The UWB PD detection system consists of the UWB UHF coupler, the UWB low noise amplifier (LNA) and the oscilloscope. The dual bands for PD signals are 0.5-2GHz(full band) and 1-2GHz(high band). As results, propagation characteristics of GIS PD signals were measured in the mock-up GIS bus and it was found that the propagation characteristics of the high band showed a better result in accordance with the infernal configuration of the GIS bus than those of the full band.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.142-145
• /
• 2001

In this paper the electromagnetic torque developed in IPMSM(Interior Permanent Magnet Synchronous Motor) is analyzed. If flux distributions in the motor are not sinusoidal, a sinusoidal current produces important torque ripple. Torque ripple causes vibration and noise of motors. The optimized current waveforms for ripple free is able to be obtained by analysis of Back-EMF and torque equation. The method to find the optimal current is based on numerical predetermination. In this paper proposes current waveform which can eliminate the torque ripple, and the validity is verified through the simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.4
• /
• pp.798-806
• /
• 2001

As electronic industry and radio communication technologies progress, the electrical and electronic equipments are lightened, minimized, and operated by low power. At the same time, these equipments react sensitively by electromagnetic wave noise. It is a origine these equipments to wrong-operation. In this paper, we focused on the design and preperation condition of a advanced EMI filter. This filter sowed superior attenuation effect of 10 dB~20 dB compare with typical filter in the range of frequency from 150 kHz to 30 GHz and superior character over the variation of a load.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.171-173
• /
• 1995

Slot field harmonics exist in air gap due to inevitable slot constructure of induction motors. They give rise to noise by the electromagnetic vibration and mechanical pulsation. We calculate the slot field harmonics for varying the ratio of slot width vs teeth pitch using the carter's coefficent. We computate the flux density in air gap by FEM(Finite Element Method) and analyze it in frequency domain using DFT(Discrete Fourier Transform). We develop the new algorithm mixing FEM with DFT.

• 한국가시화정보학회:학술대회논문집
• /
• 2002.11a
• /
• pp.53-54
• /
• 2002

Plasma ignition method has been applied in various fields particularly to the rocket propulsion, pyrotechnics, explosives, and to the automotive air-bag system. Ignition method for those applications should be safe and also operate reliably in hostile environments such as; electromagnetic noise, drift voltage, electrostatic background and so on. In the present study, a semiconductor bridge (SCB) plasma ignition device was fabricated and its plasma characteristics including the propagation speed of the plasma, plasma size, and plasma temperature were investigated with the aid of the visualization of micro scale plasma $(i.e.,\;\leq\;350\;{\mu}m)$, which generated from a Micro-Electro-Mechanical poly-silicon semiconductor bridge (SCB).