• Bulletin of the Korean Space Science Society
• /
• 1993.04a
• /
• pp.7.1-7
• /
• 1993

위성의 정밀 거리 결정을 위해 1993년 9월 5일부터 IS일간 중국의 상해 천문대 Sheshan관측소와 장춘 인공위성 관측소에서 LAGEOS 11 (Laser Geodynamics Satellite II)에 대한 SLR (Satellite Laser Ranging) 관측을 수행하였다. SLR 관측에서는 지상의 관측소에서 발사한 LASER 펄스 (pulse)가 반사경들(retroflectors)로 둘러싸인 인공위성에 반사되어 돌아오는 RTT (Round Trip Time)를 측정하여 위성까지의 거리를 결정하는데, 관측된 시간과 거리 자료는 많은 잡음(noise)를 포함하고 있기 때문에 정확한 자료를 얻기 위해서는 많은 보정이 필요하다. 관측된 시간, 거리 자료를 지상 목표물 조준(ground target ranging )에 의한 system보정, 원자시계와 GPS에서 수신된 시간과의 시간 비교, 측정된 온도, 기압, 상대 습도에 따른 대기 영향의 보정 등을 통해 오차를 줄이고 다시 LASERF beam의 대기 굴절에 따른 거리 변화 보정, 위성의 질량 중심 거리(offset) 보정, 조석력에 의한 변화값 보정, 전자기적 지연(electromagnetic delay)에 의한 상대론적 보정등을 통해서 정밀한 거리 자료를 얻었다.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.2
• /
• pp.43-51
• /
• 2017

In this study, the effect of the steering vector model mismatch due to array uncertainties on the performance of array processing was analyzed through simulation, along with the alleviation of the model mismatch effect depending on array calibration. To increase the reliability of the simulation results, the actual steering vector of the array antenna obtained by electromagnetic simulation was used along with the Jahn's channel model, which is an experimental channel model. Based on the analysis of the power spectrum for each direction, beam pattern, and the signal-to-interference-plus-noise ratio of the beamformer output, the performance deterioration of array processing due to array uncertainties was examined, and the performance improvement of array processing through array calibration was also examined.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.505-510
• /
• 2008

FBG Sensor, which is smaller than strain gauge and has better durability and does not have a noise from electromagnetic waves, was adapted to develope a smart anchor. A series of pullout tests were performed to verify the feasibility of smart anchor and find out the load transfer mechanism around the steel wire fixed to rock with grout. Distribution of shear stresses at steel wire-grout interface is assessed from the measured strain distribution by the optical fiber sensors and compared with stress distributions predicted by Farmer's and Aydan's formulas. It was found that present theoretical formulas may underestimate the failure depth and magnitude of shear stresses when the pullout loads increase.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.393-398
• /
• 2008

With the substantial increase of the size of structure, management and monitoring of excavation for the foundation construction becomes more difficult. Therefore, massive collapses which are related to retaining wall recently increase. However, since the study on measuring and monitoring the pre-stressing force of anchor is insufficient, behavior of anchor may not be predicted and monitored appropriately by the existing strain gauge type monitoring system. FBG Sensor, which is smaller than strain gauge and has better durability and does not have a noise from electromagnetic waves, was adapted to develope a smart anchor. A series of pullout tests were performed to verify the feasibility of smart anchor and find out the load transfer mechanism around the steel wire fixed to rock with grout.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.2
• /
• pp.313-319
• /
• 2010

GNSS receiver which uses the weak satellite signal is very vulnerable to the intentional jamming or non-intentional electromagnetic interference. One of the best method to overcome this disadvantage is to use an adaptive array antenna which has the capability of beamforming or nulling to the certain direction. In this paper, the performance of spatial adaptive null pattern control algorithm of 5 element array antenna is analyzed. A control algorithm which is designed in the 5 element array antenna is OPM(Output Power Minimization) which is eliminating the correlation characteristics between a reference antenna and the others. This algorithm can be applied effectively to the satellite navigation's CRPA because the satellite direction is not considered and GNSS signal power is below the thermal noise. The feature of the OPM algorithm is analyzed and the performance is compared with other null pattern control algorithm.

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.258-263
• /
• 1989

The configuration of Brushless DC moter is similar to the permanent magnet Synchronous moter. Power transistors are oftenly used to supply the switching by feedback signals of rotor positioning sensors. Brushless DC moter have been used in Aerospace and Robotics where the electromagnetic noise or the sparking of the commutator contact can not be tolerated and long - lived maintenance - free operation is required. This paper describes the design of the microprocessor - based controller for the Brushless DC moter. The controller is designed to operate for the constant torque generation and variable speed control using sinusoidal PWM inverters and resolvers as rotor positioning sensors.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1715-1717
• /
• 2001

The partial-discharge(PD) is accompanied by physical and chemical phenomena, such as heat, light, noise gas, chemical transformation, electric current, and electromagnetic radiation. The PD can be detected by measuring one of these changes. Although some techniques are employed in this purpose, several obstacles interfere with an on-line measurement. Now, a fiber-optic sensor for detecting ultrasonics is suggested for the on line measurement system with high accuracy. This paper describes the basic principles fiber-optic sensor for ultrasonic measurement.

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.152-156
• /
• 2000

A Switched Reluctance Motor(SRM) has been widely studied for practical use due to recent development on technology of power electronics. Because of its advantage that are high speed driving, simple structure and easy variable-speed control, it is expected for applications to automo biles and others. However, it has some problems that are, for examples, relatively high torque ripples and electromagnetic noise. In this paper, a simple theory is presented to represent characteristic of a SRM and theoretical results are compared with experimental ones. In the theory, the inductance variations of a SRM are approximated as linear and winding resistances and the magnetic saturation are ignored. With these approximations, we derived some equations expressing load characteristics of a SRM. Also, the torque ripple was removed by applying a variable hysteresis band control.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.683-689
• /
• 1998

A control algorithm for multi-stage dampers is developed based on the mode skyhook control concept, and implemented on the full vehicle system environment. The test vehicle system is equipped with the real time controller, four-stage variable dampers and sensors. The real time controller is developed using a digital signal processor(DSP), digital I/O, A/D and D/A converters. The dampers are driven by the electromagnetic actuators of less than 20 msec response time. The sensors include accelerometers, relative displacement transducers, and steering wheel rate sensors, etc. Through a series of tests in laboratory and proving ground, the performance of the semi-active suspension system is evaluated and it is shown that the vehicle dynamic characteristics is improved with the developed damping system. Futhermore, the parameter tuning methods to enhance vehicle dynamic performance are propsoed.

• Journal of KSNVE
• /
• v.9 no.3
• /
• pp.570-576
• /
• 1999

This paper presents numerical and experimental results of modal parameter identification in a generator stator frame for 500 MW fossil power plants. A commercial finite element analysis S/W was employed for modal analysis. The generator is excited by alternating electromagnetic forces, mainly of 120 Hz in 60 Hz machines, due to magnetic field and electric current in windings. It is necessary to verify that the stator frame has adequate frequency margin from the excitation frequency to avoid possible resonance when operating. Thus, frequency margin required for the stator frame is established using the numerical and experimental results. The results show that the stator frame meets the frequency-margin requirements. Also, results of modal analysis for design modification in order to reduce weights of the stator frame without deteriorating vibration characteristics are presented.