• 제어로봇시스템학회논문지
• /
• 제17권9호
• /
• pp.882-887
• /
• 2011

A spiral electrodynamic wheel is proposed as an actuator for the contactless conveyance of a conductive rod. When rotating the wheel around the rod, a radial force, a tangential force, and an axial force are generated on the rod and cause a screw motion of the rod. The rotation of the rod is the inevitable result due to traction torque of the wheel and the unintended motion to be excluded. However, the rotating speed of the rod should be measured without mechanical contact to be cancelled out through the controller, so the electrodynamic wheel is used as a sensor measuring the rotating speed of the rod indirectly as well as an actuator. In this paper, we model the magnetic forces by the proposed wheel theoretically and compare the derived model with simulation result by Maxwell, and analyze influences on the magnetic forces by key parameters constituting the wheel. The feasibility of the conveyance system is verified experimentally.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.1106-1111
• /
• 2007

This paper is focused on design of a new active control engine mount (ACM), which is compact in size and cost effective. The ACM, consisting of an electrodynamic actuator as the active element, flat springs and a sliding ball joint, is different in structure from the previous ACM designs based on the conventional hydraulic engine mount. Dynamic characteristics of the proposed ACM are extensively investigated before a prototype ACM, which meets the design specifications, is built in the laboratory. For cost effectiveness, a feed-forward control algorithm without a feedback sensor is used for reduction of the transmitted force through the ACM from the engine. The prototype ACM is then harmonic-tested with a rubber testing machine for verification of its control performance as well as adequacy of modeling. Experimental results show that the proposed ACM is capable of reducing the transmitted force by 20 dB up to the frequency range of 60 Hz.

• 한국산학기술학회논문지
• /
• 제17권3호
• /
• pp.310-316
• /
• 2016

도전성 평판에 부분적으로 걸쳐 회전하는 축형 동전기 휠을 구동원으로 이용하는 비접촉 반송 시스템을 제안한다. 회전하는 동전기 휠에는 3축력이 발생되는데 이 중 중력방향 힘과 횡방향 힘은 자기안정성을 갖고 있으므로 공간상에서 반송 시스템의 동적 안정성을 확보하기 위해서는 길이 방향 힘만을 제어하는 것으로 충분하다. 동전기 휠은 원주 방향을 따라 주기적으로 반복되는 극성을 갖는 영구자석으로 구성되어있으므로 기본 극의 기하학적 형상이나 극수 등은 안정성 여유에 큰 영향을 미친다. 또한 휠과 전도판간의 중첩된 영역 역시 횡방향으로의 강성을 결정하는 주요 인자이므로 본 논문에서는 안정성을 성능 지표로 휠을 구성하는 주요 설계 변수에 대한 민감도 해석을 수행한다. 얻어진 설계 값을 이용하여 제작된 시스템으로 휠을 포함하는 이동 개체의 수동적인 안정성을 실험적으로 검증한다.

• 융복합기술연구소 논문집
• /
• 제3권1호
• /
• pp.1-8
• /
• 2013

High-precision surface actuator, in which in-plane motion is realized by not two-dimensional actuator superposing linear actuators but integrated planar actuator, has been developed to cope with the severe target performance like precise motion with large envelope. It is very difficult to accomplish the performance with the traditional actuating principle. So, various methods have been tried to break through the problem. This paper discusses some meaningful trials performed in the Nano Measurement and Precision Motion Control Lab. of Korea National University of Transportation.

• Journal of Electrical Engineering and Technology
• /
• 제12권3호
• /
• pp.1073-1081
• /
• 2017

Inductive dynamic drives (IDD) are ultra rapid actuators where the moving part (disc) is subjected to impulse force. This paper presents the second model of inductive dynamic drive - a mechanical model where analytic- numerical approach was applied. The magnetic pressure, which was determined on the basis of the results obtained in the electrodynamic model, becomes the input data for mechanical model. Research with application of the mechanical model is necessary in order to determine the proper disc oscillation frequency and to obtain the stress state control for drive elements to be designed. Also, the selection of drive parameters to keep the disc deformation insignificant (while oscillating) is a condition under which these models do not need to be coupled together.