• 대한전기학회논문지
• /
• 제39권9호
• /
• pp.964-975
• /
• 1990

This paper aims at the design of high voltage electrode contour under specified field condition. Defining the contour with B-Spline curve, the number of contour variables can be reduced and very smooth electrode can be obtained. For the analysis of the electric field, Surface Charge Method which has advantages in practical model has been used. As an initial contour, the rod-plane gap has been used since the difference between maximum and minimum field value is relatively large. Various field conditions including uniform field condition are given to the end of the rod electrode. Under uniform field condition, authors designed an electrode whose field-deviation was under 0.5%. Finally, the relation between the curvature and field of the electrode has been checked, which showed that B-Spline curve is appropriate for the shape function.

• 대한기계학회논문집
• /
• 제18권11호
• /
• pp.3008-3020
• /
• 1994

Condensation heat transfer on a single horizontal tube with electric fields (Electro-Hydro-Dynamics, (EHD)) has been studied experimentally. Results are presented for EHD enhanced condensation of R-113 on a single horizontal tube using several electrode geometries. Especially, its attention was focused on the effects of electrode geometry, electric field strength and the gap of the electrode. In this study, single wire, helical, ring and mesh electrode were used. The range of the imposed voltage was 0~20 kV. As the voltage was increased the surface of liquid became an unstable wave, stream jet, liquid column and then liquid extraction in sequence. Among the various kinds of electrodes, the single wire electrode is suitable for practical application.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.502-505
• /
• 2007

In this paper we propose a novel electrode structure for high transmittance in the Patterned Vertical Alignment (PVA) LC cell. Normally, the transmittance of PVA LC cell is depended on the shape of the electrode and cell gap. We studied the area decreasing the transmittance through the electrode structure for wide viewing angle and proposed new electrode design to change LC director configuration in the area. We use the 'TechWiz LCD' for calculation of the director configuration and optical characteristics. We show the comparison of the calculated optical transmittance between the conventional PVA mode and the proposed PVA mode. From the results, we confirm that the optical transmittance of the proposed structure of the PVA cell becomes higher.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.942-945
• /
• 2001

Pulse electrochemical micromachining offers significant improvements in dimensional accuracy as compared with conventional electrochemical machining. One primary issue in pulse electrochemical micromachining is to identify and control machining depth as well as interelectrode gap size. This paper presents an identification method for the machining depth by in-process analysis of machining current and interelectrode gap size. The inter electrode gap characteristics, including pulse current, effective volumetric electrochemical equivalent and electrolyte conductivity variations, are analysed based on the model and experiments.

• 한국환경과학회지
• /
• 제20권5호
• /
• pp.623-630
• /
• 2011

This study investigated the degradation of N, N-Dimethyl-4-nitrosoaniline (RNO, indicator of the generation of OH radical) by using dielectric barrier discharge (DBD) plasma. The DBD plasma reactor of this study consisted of a quartz dielectric tube, titanium discharge (inner) and ground (outer) electrode. The effect of shape (rod, spring and pipe) of ground electrode, diameter (9~30 mm) of ground electrode of spring shape and inside diameter (4~13 mm) of quartz tube, electrode diameter (1~4 mm), electrode materials (SUS, Ti, iron, Cu and W), height difference of discharge and ground electrode (1~15.5 cm) and gas flow rate (1~7 L/min) were evaluated. The experimental results showed that shape of ground electrode and materials of ground and discharge electrode were not influenced the RNO degradation. The thinner the diameter of discharge and ground electrode, the higher RNO degradation rate observed. The effect of height gap of discharge between ground electrode on RNO degradation was not high within the experimented value. Among the experimented parameters, inside diameter of quartz tube and gas flow rate were most important parameters which are influenced the decomposition of RNO. Optimum inside diameter of quartz tube and gas flow rate were 7 mm and 4 L/min, respectively.

• 대한환경공학회지
• /
• 제31권1호
• /
• pp.29-34
• /
• 2009

표면처리폐수 내 질산성 질소를 제거하기 위한 전기화학적 처리공정에서 전극간격, 환원제, 1단 처리수 반송, 타 물질과 동시 처리 등 네 가지 조건을 변화시키며 실험을 진행하였다. 실험 결과, 전극간격은 10 mm일 때 질산성 질소 제거효율이 높았으며 10 mm 보다 전극간격이 좁아질 경우 농도분극 현상의 증가로 인해 제거효율이 감소하며 10 mm 보다 넓어질 경우 전압이 상승하여 에너지 소모가 증가하였다. 환원제 영향에 대한 실험 결과, 질산성 질소가 환원되는 과정에서 수소가 소모되기 때문에 수소이온 농도가 높은 산성조건에서 더 원활한 환원반응이 이루어졌으며 아연을 1.2배 투입할 경우 질산성 질소와의 반응량이 증가하여 질산성 질소 제거효율이 증가하였다. 1단 처리수를 반송할 경우 난류가 형성되어 환원전극에 부착된 아연이 탈착되어 재 이용되고 내부 확산이 증가하여 농도분극현상이 감소함으로 인해 질산성 질소 제거효율이 증가하였으며 아연 투입량 감소 효과가 나타났다. 암모니아성 질소는 질산성 질소 제거에 영향을 미치지 않았고 폐수 내 염소성분이 충분할 경우 질산성 질소와 동시 처리에도 문제가 없는 것으로 나타났다. 중금속은 환원되는 과정에서 전자를 소모하여 질산성 질소 제거효율은 감소하지만 전류밀도 증가나 본 장치의 전단을 중금속 제거용으로 사용하는 방법 등으로 해결이 가능할 것으로 생각한다.

• 한국공작기계학회논문집
• /
• 제14권5호
• /
• pp.13-20
• /
• 2005

Micro EDM process is generally used for machining microholes, cavities, and three dimensional shapes. For machining micro structures, first of all, micro tool electrode is indispensable and WEDG system is proposed for tool fabrication method. When using WEDG, its machining characteristics are highly affected by many EDM parameters such as applied voltage, current, rotation speed, capacitance, and pulse duration. Therefore, the design of experiment is introduced to fully understand the effect of the EDM parameters on machining tool electrode. And an attempt has been made to develop the mathematical model for predicting the size of the tool electrode by calculating spark distance. The suggested model was verified with experiment and predicted working gap distance is in good accord with the measured value.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1993년도 추계학술발표회논문집
• /
• pp.58-62
• /
• 1993

This paper shows the discharge characteristics of liquid nitrogen under plane to plane electrode, needle to plance electrode, inserting teflon insulator in plane to plane electrode at atmospheric pressure. The main experimental device of this paper is cryostat. The important results obtained from this study are sa follows. Breakdown voltage of LN2 under N-P electrode is higher than that of under P-P electrode at atmospheric pressure. Breakdown duration time is longer with increase of electode gap under the P-P, N-P electrodes. The formation of bubbles by evaporation is observed in spite of non-applying source at atmospheric pressure and the creation of corona confirmed. Breakdown voltage and breakdown duration time are in proportion to increase of diameter in case of inserting teflon insulator. Partial discharge characteristics of thickness 0.5[mm] is that 채굼 voltage of teflon insulator rose with increase of diameter in each [pps].

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.835-840
• /
• 2011

본 연구에서는 직경이 50mm, 두께가 4.5mm인 디스크형 압전 변압기의 구동부와 발전부의 전극에 대한 대칭성을 고려하여 2, 4 및 8등분으로 각각 분할하였다. 이렇게 분할된 압전 변압기에 부하저항을 변화($100{\Omega}{\sim}10_{K\Omega}$)시키면서 전기적 특성을 측정하고, 이를 토대로 한 압전변압기의 승압비 및 효율에 관한 메카니즘을 정량적으로 해석하였다.

• 한국정밀공학회지
• /
• 제23권6호
• /
• pp.104-110
• /
• 2006

A design and control of electrostatic suspension system for flexible objects is presented. A number of electrode pairs of which the number depends on the object flexibility are positioned above the object and the voltages applied to each electrode pair are controlled, independently on the others, on the basis of the gap length. To implement the system with low cost and compactness, switched-voltage control scheme that is based on the relay feedback control is utilized. Relay feedback control method deploys only a single high-voltage power supply that can deliver a DC voltage of positive and/or negative polarity and thus high voltage amplifiers that are costly and bulky are not needed any more. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping originating from the electrodes and levitated object. Employing fourteen electrode pairs, a thin aluminum plate with a thickness of 0.1 mm has been suspended at a gap length of 0.75mm.