• Journal of Advanced Marine Engineering and Technology
• /
• 제19권2호
• /
• pp.56-66
• /
• 1995

Recently, with theraped advancement in th oceanology such an ocean-going vessel and oceanic structures, there is a need to study the cavitation erosion-corrosion control of pump impeller, the partial element of ocean machinery, for more effective operation. Especially, the cathodic protection (impressed current method & Al-sacrificial anode method) was applied to sea water, and Cu-alloy material mixed Zn & Al was used as a control method of cavitation erosion-corrosion. In this study, used the piezoelectric vibrator with 20KHz, 24.mu.m to cavity generation apparatus, and investigated the weight loss, weight loss rate, electrode potential & current density etc. under this condition. According to test result, thos describes how to indentify an influence of the cathodic protection and Al & Zn addition in material development for the control of cavitation erosion-corrosion, and those will serve as fundamental data on the cavitation erosion-corrosion control of oceanic centrifugal pump.

• Journal of Welding and Joining
• /
• 제18권1호
• /
• pp.52-58
• /
• 2000

Spot welding, namely a kind of electric resisting welding has been used widely in field of automobile and aircraft industries because of easiness to apply. Specimens used in this study was a mild steel of 1.2mm thickness and the electrode was a Cu-Cr alloy of 6mm diameter. The surface sheared of specimens after testing of tensile shear was observed by SEM(scanning electron microscope) after ultrasonic cleaning for 10min., and microstructures and grain size of all specimens were measured with using of O.M.(Optical microscope). By the means of measurement and observations of tensile shear load, fatigue strength and share surface, the weldability of spot welding was evaluated. When tensile shearing testing, fracture starting point in all specimens was took place at the bond between HAZ(Heat affected zone) and nugget. With increasing in number of layers, fatigue strength was decreased. With increasing in electric current, grain size in the HAZ became more fine.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1996년도 재료학회 추계학술발표회
• /
• pp.59-59
• /
• 1996

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.42-62
• /
• 1997

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. Recently, automobile industries are trying to replace partly steel sheets with aluminum alloy sheets. Among currently produced aluminum alloys, Al alloy sheets of Al-Mg-Si(6000 series) are being tested. Especially, 6000 series are the most probable substitute in view of strength and weldability. In this paper, an attempt was made to apply resistance spot welding to joining of dissimilar sheet metals (KS6383+SCPZn or KS6383+SHCP). An effort was made to balance heating rate in the Al alloy with that in the steel sheets by increasing electrode tip diameter. Although resistance spot welding of Al alloy sheet and sheet metals does not produce desirable nugget, it proved to have reasonable strength if optimal weld condition is found by tensile-shear strength and fatigue life test. Since spot weld joints in automobile are always experiencing repeated load, spot welding methodology proposed in this paper is found to be not suitable to automobile body manufacturing.

• 마이크로전자및패키징학회지
• /
• 제27권2호
• /
• pp.45-51
• /
• 2020

미래의 유연 전자 기기는 고온, 고습 환경 조건에서 사용될 수 있으며 반복적으로 굽히고 펴기를 반복하기 때문에 장기 신뢰성 확보를 위해서는 환경 조건과 반복 기계적 변형의 효과를 동시에 고려해야 한다. 본 연구에서는 전자기기에서 가장 일반적으로 사용되는 Al, Ag, Cu 전극을 유연 기판상에 진공 증착한 뒤 환경적인 요건을 상온/일반습도와 85℃/85% 습도 두 가지로 조건에서, 기계적 변형이 없는 평평한 상태와 반복적으로 굽힘 변형을 가해주는 조건의 총 4가지 환경 및 피로 복합 실험을 실시하였다. Al, Ag, Cu 전극 모두 기계적 변형이 없는 평평한 경우에 일반 환경 조건 및 고온/고습 조건 모두 10시간 동안 전기 저항 변화가 발생하지 않았다. 일반 환경 조건에서 굽힘 피로 실험을 진행한 경우, Al, Ag, Cu 전극 모두 금속의 피로 파괴 현상에 의해 10만 싸이클 이후 전기 저항이 약 400%~600% 증가하였다. 고온/고습에서 피로 실험의 경우, Al, Ag 전극은 일반 조건 피로 실험과 결과가 유사하였으나, Cu의 경우 고온/고습 피로실험의 경우 10만 싸이클 이후 전기 저항이 90000% 이상 증가하였다. 이는 부식과 기계적 피로가 동시에 발생할 경우 금속 전극에 매우 심각한 신뢰성 문제를 유발한다는 것을 의미하며, 환경 조건과 기계적 변형을 동시에 고려한 전극 소재 디자인이 필요하다는 것을 의미한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권1호
• /
• pp.51-58
• /
• 1991

Corrosion fatigue test was performed by the use of plane bending fatigue tester in marine environment having various specific resistance from 25(natural sea water) to 5000.ohm.cm. It is in order to investigate the effects of marine environmental factor on the corrosion fatigue fracture of SS41 steel. The main results obtained are as follows; 1. The aspect ratio(b/a) of corner crack growing in natural sea water is lower than that in air. 2. The surface crack growth rate(da/dN) in marine environment is faster than that in air and da/dN delaies with the specific resistance increased. 3. The experimental constant m of paris rule [da/dN=C(${\delta}$K)$^m$] decrease with the specific resistance decreased and the effect of corrosion in proportion to the specific resistance is more sensitive than that of stress intensity factor range(${\delta}$K) under region II. 4. The accelerative factor(${\alpha}$) in marine environment is about 1.1-2.7 and .alpha. is increase under the low region of stress intensity factor range(${\delta}$K). 5. The electrode potential($E_0$) gets less noble potential with the specific resistance decreased.

• 한국전기전자재료학회논문지
• /
• 제18권11호
• /
• pp.983-989
• /
• 2005

[ $PZT(Pb(Zr,Ti)O_3)$ ] thin films were deposited by multi-target reactive sputtering method on $RuO_2$ substrates. Pure perovskite phase PZT films could be obtained by introducing Ti-oxide seed layer on the $RuO_2$ substrates prior to PZT film deposition. The PZT films deposited on the $RuO_2$ substrates showed highly voltage-shifted hysteresis loop compared with the films deposited on the Pt substrates. The surface of $RuO_2$ substrate was found to be reduced to metallic Ru in vacuum at elevated temperature, which caused the formation of oxygen vacancies at the initial stage of PZT film deposition and gave rise to the voltage shift in the P-E hysteresis loop of the PZT capacitor. The fatigue characteristics of the PZT capacitors under unipolar wane electric field were different from those under bipolar wane. The fatigue test under unipolar wane showed the increase of polarization. It was thought that the ferroelectric domains which had been pinned by charged defects such as oxygen vacancies and the charged defects were reduced in number by combining with the electrons injected from the electrode under unipolar wave, resulting in the relaxation of the ferroelectric domains and the increase of polarization.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2006년도 추계학술대회 발표 논문집
• /
• pp.170-173
• /
• 2006

Ferroelectric $Bi_{3.35}Sm_{0.65}Ti_3O_{12}(BST)$ thin films were deposited on $Pt(111)/Ti/SiO_2/Si(100)$ substrates by a sol-gel spin-coating process. In this experiments, $Bi(TMHD)_3$, $Sm_5(O^iPr)_{13}$, $Ti(O^iPr)_4$ were used as precursors, which were dissolved in 2-methoxyethanol. Thereafter, the thin films with the thickness, of 240nm were annealed from 600 to $720^{\circ}C$ in oxygen atmosphere for 1 hr, and post-annealed in oxygen atmosphere for 1 hr after deposition of Pt electrode to enhance the electrical properties. The remanent polarization and coercive voltage of the BST thin films annealed at $720^{\circ}C$ were $19.48\;{\mu}C/cm^2$ and 3.40 V, respectively, and a fatigue-free characteristics. As a result, Sm-substituted bismuth titanate films with good ferroelectric properties and excellent fatigue resistance are useful candidates for ferroelectric memory applications.

• Journal of Welding and Joining
• /
• 제8권1호
• /
• pp.62-69
• /
• 1990

Being focused on the recent studies that the fatigue strength of resistance spot weldmentes can be improved by using ellipsoidal weld nuggets, the voltage and temperature distribution in resistance spot weldments were simulated for the various rectangular electrodes which had the different aspect ratio of the contact area. Because the electrode shape was not axi-symmetric, the solution domain for simulation should be three dimensional. A series of experiments were carred out to verify the analytically obtained temperature distribution in the weldment. From the calculational and experimental results, it could be revealed that the nugget took the form of ellipsoid, while both results showed a considerable discrepancy for the high aspect ratio.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.101-102
• /
• 2006

PZT thin films, which are the representative ferroelectric materials in ferroelectric random access memory (FRAM), have some serious problem such as the imprint, retention and fatigue which ferroelectric properties are degraded by repetitive polarization. BL T thin film capacitors were fabricated by plasma etching, however, the plasma etching of BLT thin film was known to be very difficult. In our previous study, the ferroelectric materials such as PZT and BLT were patterned by chemical mechanical polishing (CMP) using damascene process to top electrode/ferroelectric material/bottom electrode. It is also possible to pattern the BLT thin film capacitors by CMP, however, the CMP damage was not considered in the experiments. The properties of BLT thin films were changed by the change of polishing pressure although the removal rate was directly proportional to the polishing pressure in CMP process.