• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.213-226
• /
• 2022

In the present study, the corrosion behavior of aluminum Al-7075 tempered (T-6 condition) alloy was evaluated by immersion testing and electrochemical testing in 1.75% and 3.5% NaCl environment at acidic, neutral and basic pH. The data obtained by both immersion tests and electrochemical corrosion tests (potentiodynamic polarization and electrochemical impedance spectroscopy tests) present that the corrosion rate of the alloy specimens is minimum for the pH=7 condition of the solution due to the formation of dense and well adherent thin protective oxide layer. Whereas the solutions with acidic and alkaline pH cause shift in the corrosion behavior of aluminum alloy to more active domains aggravated by the constant flux of acidic and alkaline ions (Cl^- and OH^-) in the media which anodically dissolve the Al matrix in comparison to precipitated intermetallic phases (cathodic in nature) formed due to T6 treatment. Consequently, the pitting behavior of the alloy, as observed by cyclic polarization tests, shifts to more active regions when pH of the solutions changes from neutral to alkaline environment due to localized dissolution of the matrix in alkaline environment that ingress by diffusion through the pores in the oxide film. Microscopic analysis also strengthens the results obtained by immersion corrosion testing and electrochemical corrosion testing as the study examines the corrosion behavior of this alloy under a systematic evaluation in marine environment.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.2
• /
• pp.92-97
• /
• 2011

In this study we have investigated the Li-ion coordination, thermal behavior and electrochemical stability of N-butyl-N-methyl-pyrrolidinium bis(trifluoromethanesulfonyl)imide ($Py_{14}TFSI$) with lithium bis(trifluoromethanesulfony)imide (LiTFSI) doping intended for use as electrolytes for lithium batteries. The ionic conductivity is reduced and glass transition temperature ($T_g$) increases with LiTFSI doping concentration. Also, the electrochemical stability increases with LiTFSI doping. A high LiTFSI doping could enhance the electrochemical stability of electrolytes for lithium batteries, whereas the decrease in the ionic conductivity limits the capacity of the battery.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.5
• /
• pp.697-706
• /
• 2005

We review the evolution of electrochemical studies of conducting polymers into the current state-of-the-art based primarily on our work. While conventional electrochemical experiments sufficed for the needs in the phase of studies of both electrochemical synthesis and characterization of conducting polymers, developments of various new experimental techniques have led to their introduction to this field for more refined information. As a result, the conventional electrochemical, spectroelectrochemical, electrochemical quartz crystal microbalance, impedance, and morphological as well as electrical characterization studies all made important contributions to a better understanding of the polymerization mechanisms and the conductive properties of these classes of polymers. From this review, we hereby expect that the electrochemical techniques will continue to play important roles in bringing this field to the practical applications such as nanoscale electronic devices.

• Corrosion Science and Technology
• /
• v.15 no.6
• /
• pp.259-264
• /
• 2016

With a specially designed electrochemical cell, the changes in impedance behavior for Inconel 600 and aluminide diffusion coatings under molten sulfate film with thermal cycles (from $800^{\circ}C$ to $350^{\circ}C$) were monitored with electrochemical impedance measurements. It was found that corrosion resistance for both materials increased with lower temperatures. At the same time, the state of molten salt was also monitored successfully by measuring the changes in impedance at high frequency, which generally represents the resistance of molten salt itself. After two thermal cycles, both Inconel 600 and aluminide diffusion coatings showed excellent corrosion resistance. The results from SEM observation and EDS analysis correlated well with the results obtained by electrochemical impedance measurements. It is concluded that electrochemical impedance is very useful for monitoring the corrosion resistance of materials under molten salt film conditions even with thermal cycles.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.3
• /
• pp.430-438
• /
• 1997

Deburring and edge finishing technology as the final process of machining operation is required for manufacturing of advanced precise conponents. But, deburring is considered as a difficult problem on going to the high efficient production and automation in the FMS. Removal of burr couldn't have a standard of its definition because of its various shapes, dimensions and properties and mostly depends on manual treatment. Especially, deburring for cross hole inside is very difficult owing to its shape passing through out perpendicular to a main hole. The electrochemical method is suggested as its solution in practical aspect. Therefore, electrochemical deburring technology needs to be developed for the high efficiency and automation of internal deburring in the cross hole. In this study, the new process in the eliminating burr inside cross hole, electrochemical deburring by the wheel electroplated with Cubic-Boron-Nitrade abrasives, is suggested. Its deburring mechanism is described and machining performances is investigated. Also, CBN electroplated wheel is designed and manufactured and then characteristics of electrochemical deburring are investigated through experiments. Overall electrochemical deburring performance against burr inside cross hole is examined in the various power sources such as peak current and direct current.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.4
• /
• pp.462-471
• /
• 2022

In this study, the electrochemical impedance characteristics of CO₂/H₂O co-reduction to produce CO/H₂ syngas were investigated in a low-temperature single cell. The effect of the operating conditions on the single-cell performance was evaluated at different feed concentrations and cell voltages, and the corresponding electrochemical impedance spectroscopy (EIS) data were collected and analyzed. The Nyquist plots exhibited two semicircles with separated characteristic frequencies of approximately 1 kHz and tens of Hz. The high-frequency semicircles, which depend only on the catholyte concentration, could be correlated to the charge transfer processes in competitive CO₂ reduction and hydrogen evolution reactions at the cathodes. The EIS characteristics of the CO₂/H₂O co-reduction single cell could be explained by the equivalent circuit suggested in this study. In this circuit, the cathodic mass transfer and anodic charge transfer processes are collectively represented by a parallel combination of resistance and a constant phase element to show low-frequency semicircles. Through nonlinear fitting using the equivalent circuit, the parameters for each electrochemical element, such as polarization resistances for high- and low-frequency processes, could be quantified as functions of feed concentration and cell voltage.

• Carbon letters
• /
• v.19
• /
• pp.32-39
• /
• 2016

In this work, we studied the effects of electrochemical oxidation treatments of carbon fibers (CFs) on interfacial adhesion between CF and epoxy resin with various current densities. The surface morphologies and properties of the CFs before and after electrochemical-oxidation-treatment were characterized using field emission scanning electron microscopy, atomic force microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and single-fiber contact angle. The mechanical interfacial shear strength of the CFs/epoxy matrix composites was investigated by using a micro-bond method. From the results, electrochemical oxidation treatment introduced oxygen functional groups and increased roughness on the fiber surface. The mechanical interfacial adhesion strength also showed higher values than that of an untreated CF-reinforced composite.

• Journal of Electrochemical Science and Technology
• /
• v.4 no.4
• /
• pp.125-139
• /
• 2013

The electrical conductive polymers (ECPs) reported at my research group are introduced in this review, which works are started from the late Professor Su-Moon Park's pioneering research for polyaniline at the University of New Mexico. The electrochemical and spectroelectrochemical properties and their applications to sensor and energy conversion systems are briefly described. At first, the growth and degradation mechanism of polyaniline describes and we extend to polypyrrole, polyazulene, polydiaminonaphthalenes, and polyterthiophene derivatives. In addition, the preparation of monomer precursors having functional groups is briefly described that can give us many exceptional applications for several chemical reactions. We describe the application of these ECPs for the fabrication of chemical sensors, biosensors, biofuel cells, and solar cells.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1093-1096
• /
• 2001

Eletrochemical phenomenon are employed in the manufacturing of micro-electrochemical machining(micro-ECM). The application of controlled electrochemical metal removal in the fabrication of microstructures and microcomponents is refer to as micro-electrochemical machining. In this paper, we introduce a new method named $\ulcorner$point-electrode electro chemical machining method$\lrcorner$ was proposed to establish micro fabrication technology by use of electrochemical machining. And we find effect of the electrochemical phenomenon in several conditions.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.4
• /
• pp.202-208
• /
• 2002

We have been investigating electropolymerization of pyrrole in aqueous electrolyte solutions in acidic as well as in neutral conditions by in situ electrochemical quartz crystal oscillator method, where resonant frequency and resonant resistance can be monitored simultaneously with current-voltage measurements during electropolymerization of pyrrole. The properties of thin PPy films prepared on electrode surfaces depended strongly on the experimental variables of electrode potentials applied, solution pH, kinds and quantity of supporting electrolytes, added chemicals, and the mode of electrochemical method employed. We are applying our experience gained on electropolymerization of pyrrole to immobilizing biomolecules onto electrode surfaces to develop a biosensor system. In this work, we wish to present the results on electrochemical monitoring on electropolymerization of pyrrole in the presence of DNA and albumin in different electrochemical conditions. Additionally we will summarize our investigations on the miniaturization of biomolecules/PPy composites by means of scanning tunneling microscopy.