• Journal of Electrochemical Science and Technology
• /
• v.10 no.1
• /
• pp.14-21
• /
• 2019

Supported liquid membrane process usually is used for recovering or enrichment of valuable metals in the industrial wastewater. But, even if the metals in the wastewater was separated with high chemical selectivity, it cannot be enough concentrated since separation performance of supported liquid membrane (SLM) process is limited by concentration gradient between feed solution and stripping solution. If metal concentration in the stripping solution to be enough low, transport of metal through membrane can be accomplishment constantly. Therefore, Electrodialysis (ED) has been placed after SLM process and the stripping solution of SLM was used as the feed solution for the ED process. Transport of ions in the solutions is successfully performed by ED process. Thus, the metal concentration in the stripping solution does not rise as to stop ion transport. Besides, valuable metals easily are concentrated by ED process for re-use. In this study, effects of operation parameters like initial Cd(II) concentration, HCl concentration in the feed solution of SLM and applied voltage are investigated on separation efficiency, flux and permeability of the both processes. As the feed solution concentration increased, all performance values has increased. When initial concentration of 100 mg/L is used, separation performances (SP) are 55% and 70%, for SLM and consecutive process, respectively. The best HCl concentration in the feed solution of SLM has determined as 2 M, in this conditions SP are 64% and 72%, for SLM and consecutive process, respectively. With increased of applied voltage on ED process, SP of the consecutive process has been raised from 72% to 83%. According to the obtained experimental data, consecutive process has better separation performance than SLM. When the separation performances of both processes were compared for the same operating conditions, it was determined higher the separation efficiency, permeability and flux values of the consecutive process, 8%, 9% and %10.6, respectively. Consequently, the use of the consecutive process increases the performance efficiency of both processes. The consecutive process studied has quite a good chemical separation efficiency, and enrichment capability. Moreover, this process requires few water and energy.

• Journal of Industrial Technology
• /
• v.42 no.1
• /
• pp.1-5
• /
• 2022

Although the mileage of electric vehicles can be increased based on the excellent energy density of the LiNi_0.9Co_0.05Mn_0.05O₂, it is known that the reason for limiting its use is the low lifespan and poor surface stability due to the structural deformation of the LiNi_0.9Co_0.05Mn_0.05O₂. To improve the structural stability of LiNi_0.9Co_0.05Mn_0.05O₂, electrochemical performance is improved by La coating on the surface. La-modified LiNi_0.9Co_0.05Mn_0.05O₂ shows an initial capacity of 210.6 mAh/g, a capacity retention rate of 89.9 % after 50 cycles, and a retention rate of 52.5% at 6.0 C. These are superior performances than the pristine sample, because the structural stability of the LiNi_0.9Co_0.05Mn_0.05O₂ cathode is improved by the La coating.

• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.439-445
• /
• 2022

In this study, Silicon and petroleum pitch were coated on the surface of Si/C fiber manufactured using electrospinning to improve the electrochemical performances. SiO₂/PAN fiber was prepared by electrospinning with TEOS and PAN at various ratios dissolved in DMF. The characteristics of carbonization, reduction, and pitch coating processes were investigated for the optimal process of the pitch coated Si/C fiber anode composite. Anode composite prepared with TEOS/PAN = 4/6 (CR-46) after carbonization and reduction process has a capacity of 657 mAh/g. To improve capacity and stability, Si powder and PFO pitch were coated at the surface of CR-46. When the pitch composition was fixed at 10 wt%, it was found that the capacity increased as the weight ratio of silicon increased, but the stability decreased. The pitch coated Si/C fiber composite with 10 wt% silicon has high capacity of 982.4 mAh/g and capacity retention of 86.1%. In the test to evaluate rate performance, the rate capability was 80.2% (5C/0.1C).

• Journal of the Korean Electrochemical Society
• /
• v.23 no.2
• /
• pp.47-55
• /
• 2020

Highly loaded LiCoO₂ positive electrodes are prepared to construct high-energy density lithium-ion batteries, their electrochemical performances are evaluated. For the standard electrode, a loading of about 2.2 mAh/㎠ is used, and for a high-loading electrode, an electrode is manufactured with a loading level of about 4.4 mAh/㎠. The content of carbon black as electronic conducting additive, and the porosity of the electrode are configured differently to compare the effects of electron conduction and ionic conduction in the highly loaded LiCoO₂ electrode. It is expected that the electrochemical performance is improved as the amount of the carbon black increases, but the specific capacity of the LiCoO₂ electrode containing 7.5 weight% carbon black is rather reduced. When the conductive material is excessively provided, an increase of electrode thickness by the low content of the LiCoO₂ active material in the same loading level of the electrode is predicted as a cause of polarization growth. When the electrode porosity increases, the path of ionic transport can be extended, but the electron conduction within the electrode is disadvantageous because the contact between the active material and the carbon black particles decreases. As the electrode porosity is lowered through the sufficient calendaring of the electrode, the electrochemical performance is improved because of the better contact between particles in the electrode and the reduced electrode thickness. In the electrode design for the high-loading, it is very important to construct the path of electron conduction as well as the ion transfer and to reduce the electrode thickness.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.2
• /
• pp.145-152
• /
• 2010

The gel polymer electrolyte(GPE) were prepared by in-situ thermal cross-linking reaction of homogeneous precursor solution of perfluorinated phosphate-based cross-linker and liquid electrolyte. Ionic conductivities and electrochemical properties of the prepared gel polymer electrolyte with the various contents of liquid electrolytes and perfluorinated organophosphate-based cross-linker were examined. The stable gel polymer electrolyte was obtained up to 97 wt% of the liquid electrolyte. Ionic conductivity and electrochemical properties of the gel polymer electrolytes with the various chain length of perfluorinated ethylene oxide and different content of liquid electrolytes were examined. The maximum ionic conductivity of liquid electrolyte was measured to be $1.02\;{\times}\;10^{-2}\;S/cm$ at $30^{\circ}C$ using the cross-linker($PFT_nGA$). The electrochemical stability of the gel polymer electrolyte was extended to 4.5 V. The electrochemical performances of test cells composed of the resulting gel polymer electrolyte were also studied to evaluate the applicability on the lithium polymer batteries. The test cell carried a discharge capacity of 136.11mAh/g at 0.1C. The discharge capacity was measured to be 91% at 2C rate. The discharge capacity decreased with increase of discharge rate which was due to the polarization. After 500th charge/discharge cycles, the capacity of battery decreased to be 70% of the initial capacity.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.1
• /
• pp.200-207
• /
• 2019

In this study, flexible supercapacitor based on the all solid state electrolyte with PVA (polyvinyl alcohol)-$H_3PO_4$, ionic liquid as a BMIMBF4 (1-buthyl-3-methylimidazolium tetrafluoroborate) and reduced graphene oxide/conductive polymer composite was fabricated and characterized electrochemical properties with function of its flexibility. In order to measure and compare that electrochemical performances (including cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS) and galvanostatic charge/discharge,after 0~100th bending test) of prepared flexible supercapacitor based on reduced graphene oxide/conducting polymer composite and all solid state electrolyte, we have conducted press machine with constant pressure ( 0.01/cm2) for $100^{th}$ bending test. As a result, specific capacitance of the flexible supercapacitor was 43.9 F/g which value decreased to 42.0 and 40.1 F/g after 50 and $100^{th}$ bending test, respectively. This result exhibited that decreased electrochemical property of the flexible supercapacitor effected on physical stress on the electrode after repeated bending test. In addition, we have measured that electrode surface morphology by SEM to prove its decreased electrochemical property of the flexible supercapacitor after prolonged bending test.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.132.2-132.2
• /
• 2010

Mesoporous tinoxide ($SnO_2$) as anode materials for Li-ion battery were prepared by hydrothermal method and templating method using SBA-15 as template. And electrochemical properties of $SnO_2$ electrode were investigated with cyclic voltammogram (CV). The morphology and structures of $SnO_2$ were characterized by transmission electron microscopy (TEM) and X-ray diffractometer (XRD), respectively. The specific surface area was defined by $N_2$ adsorption with BET(Brunauer-Emmett-Teller) method. As a result, the surface area of mesoporous $SnO_2$ which was made from templating method is higher than the case of using hydrothermal method. In addition, in anodic performance, mesoporous $SnO_2$ which is prepared by templating method showed higher charge-discharge capasity compared to hydrothermal method and exhibited excellent stability over the entire cycle number. It was indicated that electrochemical performances of mesoporous $SnO_2$mainly affected to the structural features, such as specific surface area and porosity.

• Journal of the Korean Vacuum Society
• /
• v.16 no.3
• /
• pp.227-230
• /
• 2007

In the Li ion battery fabrication process, an aging step has treated as a miner step because there is not so much data to define the relationship between the phenomena generated in aging process and the battery performances. However, the OCV(open circuit voltage) change in the aging process is shown by the electrochemical absorption of the electrolyte component to the both electrodes(anode or cathode) and the absorbed layer to the electrode affects to form the solid electrolyte interface(SEI) layer during the first charge process. In this report, the adsorbed materials are designed deliberately and are cleared to affect to the SEI layer formation.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.209-209
• /
• 2003

The adventages of Li alloys have attracted the attention of many research groups, many of which have investigated tin-based alloys [1-2], Despite interesting performances of these, the irreversible capacity loss systematically observed on the first cycle for these compounds is a main drawback for their use as anode materials in lithium ion cells. Not only Sn is efficient in forming alloys with Li, Si can also react with Li to form alloys with a high Li/Si ratio, like Li$\_$22/Si$\_$5/ at 400$^{\circ}C$. It corresponds to a capacity of 4200mAh/g. Electrochemical Li-Si reaction occurs between 0 and 0.3 V against Li/Li$\^$+/, so that high-energy density battery can be realized. Despite the high theoretical capacity of elements like Si, however, particles of the alloys crack and fragment due to the repeated alloying and do-alloying which occurs as cell are charged and discharged. The research groups of Muggins [3] and Besenhard [4] have proposed that the volume expansion due to the insertion of Li can be reduced in micro- and submicro-structured matrix alloys. For this reason, the research group of J.R. Dahn investigated Sn/Mo sequential sputter deposition to prepare nanocomposites [5]. In this study, we investigated the characterization and the electrochemical characteristics of sequentially sputtered Si/Mo multilayer for microbattery anode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.241-242
• /
• 2006

In this work, the $LiFePO_4-LiCoO_2$ mixed cathode electrodes were prepared and their electrochemical performances were measured in different current density. The cell of $LiFePO_4-LiCoO_2$ observed two voltage plateau regions at 3.4 and 3.9V. The cell of $LiFePO_4-LiCoO_2$ (90:10 wt%) mixed cathode delivered a discharge capacity of ca. 139.8 mAh/g at a 0.2C rate. The capacity of the cell decreased with the current rate and a useful capacity of ca 85.7mAh/g was obtained at a 2C rate.