• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.548-553
• /
• 2013

EHPS(Electro-Hydraulic Power Steering) is a system to generate the steering operation force from the electric motor connected directly to the oil pump. To optimize the manufacturing cost and efficiency of the performance of the steering system is very important. Until now, the development of the hydraulic system is implemented by the field test which needs a significant time and cost. In this paper, flow measurement of an external gear pump is performed. Then using the experimental results, an approximate model expressed by flow rate characteristics is proposed to calculate the discharge flow rate. Proposed approximate model is verified by comparing with the experimental data and AMESim results. As the experimental data and AMESim results agree well, the approximate model data can be used as an alternative to highly cost experimental procedure.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.658-662
• /
• 1986

In the microcomputer-based velocity control for an electro-hydraulic servo system, the effects of control methods and control hardware on the performance of the system were investigated. Experiments were carried out with PID and deadbeat controllers using 8 or 16 bit microprocessor and 8 or 12 bit A/D and D/A converters. It is found that the transient response of the system is better with PID controller than with deadbeat controller. When the number of bits of the microprocessor and converters are small, it is also found that amplitude quantization due to limited wordlength gives significant effects on transient responses of the system. Analytically predicted step-responses are in good agreement with experimental ones.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.4
• /
• pp.54-69
• /
• 1991

This study deals with the position control of a hydraulic cylinder system operated by two port 3-way high speed solenoid valve in Pulse-Width-Modulation mode, instead of using conventional electro-hydraulic servovalve. Due to the complexity and the relatively poor reliability of the servovalve, an actuator using simpler and more study high speed solenoid valve will be presented. The high speed solenoid valve acts as converters of electronic pulse signal to hydraulic ones. It has been pointed out that there are practical problems to be solved in the PWM system, that is (1) accuracy of positioning control becomes considerably insufficient because the system is affected by on/off action of the solenoid valves, and (2) serious nonlinerality appears in the valve characteristics as a result of the switching behavior of the valves. As a method to overcome these defects, the differential PWM driving method of a hydraulic cylinder that improved the steady-state-error, flow rate nonlinearity in simple PWM, and the hydraulic hunting of dead time compensated-PWM driving is proposed in this study.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.4
• /
• pp.291-298
• /
• 2013

In this paper a new hybrid-type control system is proposed which reduces the pump speed of an electro-hydraulic actuator consisting of a pressure-compensated variable displacement piston pump and a valve-controlled hydraulic cylinder, whenever the flow rate demand is low. In order to avoid interfering with the pressure regulator which also has an effect on swash plate angle, the pump speed is changed in proportion to the mean value of the speed component of position commands. Additionally a pressure switch is employed to prevent the system pressure from getting lower than a reference value. Based on computer simulation & experimental results, it is shown that the hybrid control can save the idling power up to 44% at a stand-by mode by reducing the pump speed from 1,800 rpm to 600 rpm without affecting the dynamic response of the electro-hydraulic actuator.

• Journal of Drive and Control
• /
• v.16 no.3
• /
• pp.86-93
• /
• 2019

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.292-301
• /
• 2014

This paper describes development of distributed type independent electro-hydraulic ballast valve remote control system with diagnostic function based on fuzzy inference using redundant Modbus communication and ethernet Modbus TCP/IP. Diagnostic function estimate degradation of system components and diagnose system faults, which results in shortage of fault maintenance time and improvement of system safety. Slave devices which control each valve and master device which command, monitor and diagnose slave system are developed. Slave devices are connected to master device with redundant Modbus networks and master device is connected to ship's integrated control system with Modbus TCP/IP. Also this paper describes development of simulator to test and confirm whether developed system can be integrated with ship's integrated control and monitoring system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.730-735
• /
• 1992

In this study, heavy loads driving servo control systems, which are composed of electro-hydraulic servo-valve, hydraulic motor/cylinder, gear box and link mechanism, are investigated for implemention. To predict the performances of the systems, modelling and simulation with some nonlinearities are carried out. Simulation results are compared with experimental results.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.3
• /
• pp.1-6
• /
• 2010

This paper deals with the issue of simple adaptive position control for a pump-controlled cylinder system. A fixed displacement pump is utilized instead of servo valve and its speed is controlled by AC motor. The whole control system is composed of a pair of interconnected subsystems, that is, a feedback control system and a feedforward control system. From experiments it is shown that position control using simple adaptive control can accomplish significant reduction in position tracking error comparing to a conventional PID control.

• Journal of Aerospace System Engineering
• /
• v.8 no.2
• /
• pp.7-13
• /
• 2014

In order to enable fail-safe operation the electro-hydrostatic actuators can be dualized. When a symmetrical actuator is combined in series with an asymmetrical actuator with single rod cylinder, the flow rates of their cylinders are unmatched. If their position controller has same configuration, one of their pumps can supply too much flow rate under particular load conditions, which should be bypassed into low pressure side e.g. by a relief valve. In this paper it is shown how the hydraulic circuit for the asymmetrically combined electro-hydrostatic actuator can be designed without sacrificing power consumption.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.8 no.2
• /
• pp.23-28
• /
• 2011

This paper investigates the motion control of a hydraulic motor-load system using the Simple Adaptive Control (SAC) method. The plant transfer function has been modelled mathematically. The open-loop responses have been obtained experimentally in order to identify the design parameters of transfer function. The hydraulic motor-load system has been modelled using the 3D CAD and imbedded in the hydraulic circuit simulation program to verify the overall performance. The experimental results confirm that the SAC method gives a good tracking performance compared to the PID control.