• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1352-1353
• /
• 2008

In this study, aluminium - doped zinc oxide (ZnO:Al) transparent conducting film was deposited on PET(polyethylen terephthalate) substrate by r.f. magnetron sputtering method. PET substrate was surface-treated in an atmospheric pressure DBD(dielectric barrier discharge) plasma to increase deposition rate and to improve electrical propesties. Morphological changes by DBD plasma were obsered using contact angle measurement. The contact angle of water on PET was reduced from 62$^{\circ}$ to 42$^{\circ}$ by DBD plasma surface treatment. The plasma treatment also increased deposition rate and electrical propesties. The electrical resistivity as low as $4.97{\times}10^{-3}[{\Omega}-cm]$ and the deposition rate of 234[${\AA}$-m/min] were obtained in ZnO:Al film with surface treatment time of 5min, and 20min., respectively.

• Journal of Power Electronics
• /
• v.19 no.3
• /
• pp.815-826
• /
• 2019

This paper discusses a simple control approach for a Unified Power Conditioner (UPC) system to achieve power quality compensation at the point of common coupling in distribution systems. The proposed Instantaneous Power Estimation Algorithm (IPEA) for shunt and series active power filters uses a simple mathematical concept that reduces the complexity in the design of the controller. The performance of a UPC is verified with a system subjected to voltage distortions, sags/swells and unbalanced loads using MATLAB/SIMULINK. The simulation study shows that a UPC with the proposed control algorithm can effectively compensate for voltage and current harmonics, unbalance and reactive power. The control algorithm is experimentally implemented using dSPACE DS1104 and its effectiveness has been verified.

• Journal of electromagnetic engineering and science
• /
• v.12 no.2
• /
• pp.176-184
• /
• 2012

In this paper, the effects of a metal plane on the performance of a meandered slot RFID antenna are evaluated in a real environment, and 3 metal plane cases are considered (the most likely scenarios in which metal conductive materials are placed near the tag antenna). The metal plane effects can be categorized as matching degradation and antenna gain variation. First, matching degradation due to the antenna's induced mutual impedance is experimentally investigated. In addition, the gain variation is investigated to figure out the change in the radiation characteristics. With the derived antenna parameters, the read range is calculated with the Friis transmission equation and measured to analyze the effects of a metal plane on RFID system performance. The calculated and measured read range varies from 9.3 m to 19.1 m as the distance between the RFID antenna and the metal plane changes.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.515-525
• /
• 2022

The wireless power transfer (WPT) charging system for AGV depends highly on the coupling conditions due to air gap variation. To attain stable output power with high transfer efficiency under various coupling conditions, a single-stage, DC-DC converter that operates with robustness to changes in air gaps is proposed for the WPT system. The proposed converter is capable of soft switching under the set input voltage (V_in: 380 V_DC), load conditions (0-1 kW), and air gap changes (30-70 mm). In addition, a wide output voltage range (Vo: 39-54 V_DC) can be controlled by varying the link voltage due to the phase control at a fixed switching frequency. Experimental results are verified using a prototype of a 1 kW wireless power charging system.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.3
• /
• pp.346-352
• /
• 2009

The eventual goal of this paper is to help the generating companies and load-serving entities to choose appropriate relative levels of interconnected system versus bilateral trades while considering risk, and economic performance. In competitive power markets, electricity prices are determined by balance between demand and supply in electric power exchanges or bilateral contracts. The problem formulation is bilateral contract incorporated into Multi-area unit commitment with import/export and tie-line constraints. This proposed method considers maximizing own profit or minimize the operating cost among the generating companies in multi-area system. The feasibility of the proposed algorithm has been demonstrated using IEEE system with four areas and experimental results shows that proposed method is reliable, fast and computationally efficient

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.136-142
• /
• 2014

A major problem in Switched Reluctance Motor (SRM) is torque ripple, which causes undesirable acoustic noise and vibration. This work focuses on reducing the undesirable torque ripple in SRM by modifying stator and rotor geometry. This paper presents a comparative study on torque ripple minimization in SRM with modified pole shapes such as stator pole taper, stator pole face with non-uniform air gap and pole shoe attached to rotor pole. Further this paper presents a detailed sensitivity analysis of the effect of different geometrical parameters that alter the pole face shapes on the performance of SRM. The analysis is performed using finite-element method considering average torque and torque ripple as performance parameters. Based on the analysis, a design combining stator pole taper with non-uniform air gap is proposed to improve the torque characteristics of SRM. The dynamic characteristics of the proposed design are simulated and the results show satisfactory reduction in torque ripple.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1269-1276
• /
• 2014

The main objective of this paper is to design DC-DC MPPT circuit using chaotic pulse width modulation to track maximum power from solar PV module for space application. The direct control method of tracking is used to extract maximum power. The nominal duty cycle of the main switch of DC-DC SEPIC converter is adjusted so that the solar panel output impedance is equal to the input resistance of the SEPIC converter which results better spectral performance in the tracked voltages when compared to conventional PWM control. The conversion efficiency of the proposed MPPT system is increased when CPWM is used as a control scheme

• Journal of Electrical Engineering and Technology
• /
• v.1 no.4
• /
• pp.546-549
• /
• 2006

In this paper the neuron operation based on Brillouin-active fiber in optical fiber is described. The inherent optical feedback by the backscattered stokes wave in optical fiber leads to instabilities in the form of optical chaos. Controlling of chaos induced transient instability in Brillouin-active fiber is implemented with Kerr nonlinearity having a non-instantaneous response in network systems. The controlling chaotic instabilities can lead to multistable periodic states; create optical logic 'on' or high level '1' or 'off', or low level '0'. It is theoretically possible to apply the multi-stability regimes as an optical memory device for encoding and decoding series and complex data transmission in optical systems.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.4
• /
• pp.210-214
• /
• 2006

In this paper, two sampling methods which are Latin hypercube sampling (LHS) and simple random sampling were. compared to improve the modeling speed of neural network model. Sampling method was used to generate initial weights and bias set. Electrical characteristic data for $HfO_2$ thin film was used as modeling data. 10 initial parameter sets which are initial weights and bias sets were generated using LHS and simple random sampling, respectively. Modeling was performed with generated initial parameters and measured epoch number. The other network parameters were fixed. The iterative 20 minimum epoch numbers for LHS and simple random sampling were analyzed by nonparametric method because of their nonnormality.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1439-1450
• /
• 2013

This paper investigates a robust neuro-fuzzy control (NFC) method which can accurately follow the speed reference of an interior permanent magnet synchronous motor (IPMSM) in the existence of nonlinearities and system uncertainties. A neuro-fuzzy control term is proposed to estimate these nonlinear and uncertain factors, therefore, this difficulty is completely solved. To make the global stability analysis simple and systematic, the time derivative of the quadratic Lyapunov function is selected as the cost function to be minimized. Moreover, the design procedure of the online self-tuning algorithm is comparatively simplified to reduce a computational burden of the NFC. Next, a rotor angular acceleration is obtained through the disturbance observer. The proposed observer-based NFC strategy can achieve better control performance (i.e., less steady-state error, less sensitivity) than the feedback linearization control method even when there exist some uncertainties in the electrical and mechanical parameters. Finally, the validity of the proposed neuro-fuzzy speed controller is confirmed through simulation and experimental studies on a prototype IPMSM drive system with a TMS320F28335 DSP.