• 조명전기설비학회논문지
• /
• 제29권3호
• /
• pp.69-80
• /
• 2015

This paper is writing about developing magnet power supply. It is very important for power supply to obtain output current in high precision and high stability. As a switching noise and a power noise are the cause of disrupting the stability of output current, to remove these at the front end, low pass filter with 300Hz cutoff frequency is designed and placed. And also to minimize switching noise of the current into magnet and to stop abrupt fluctuations, output filter should be designed, when doing this, we design it by considering load has high value inductance. As power supply demands the stability of less than 5ppm, high precision 24bit(300nV/bit) analog digital converter is needed. As resolving power of 24bit(300nV/bit) analog digital converter is high, it is also very important to design the input stage of analog digital converter. To remove input noise, 4th order low pass filter is composed. Due to the limitation of clock, to minimize quantization error between 15bit DPWM and output of ADC having 24bit resolving power, ${\Sigma}-{\Delta}$ modulation is used and bit contracted DPWM is constituted. And before implementing, to maximize efficiency, simulink is used.

• 한국조명전기설비학회지:조명전기설비
• /
• 제2권2호
• /
• pp.59-63
• /
• 1988

고정 AC 전력전원에서 PWN(Pulse Width Modulation) 기법은 전압과 기본파 주파수를 가변 시키는 데 이용되어 왔다. 종래의 PWN 기법은 전류수, 필터크기 등의 문제점 때문에 PWN 출력 전압파형을 모터 구동 등의 제어 대상에 응용하는 연구가 진행되었다. 그러나 본 논문에서는 출력단 고속 스윗칭 소자를 사용하여 캐리어 주파수를 10(KHz)-45(KHz)까지 정현 PWN 시키고, 인버터의 출력단 파형은 소용량LPF(Low Pass Filter)를 사용하여 PAM(Pulse Amplitude Modulation)을 얻어냈다. 정현 PWN 제어 회로는 속응성과 제어성을 고려하여 마이크로 프로세서와 아날로그 회로로 혼합구성 하였다. 그리고 실험 결과는 변조도 0.6-1.0까지 변할 때 전압 파형을 관찰했다.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권4호
• /
• pp.165-169
• /
• 2004

This paper reports a miniaturized conductor-backed CPW (CBCPW) bandpass filter based on a thin film polyimide layer coated on CMOS-grade silicon. With a 20 ${\mu}{\textrm}{m}$-thick polyimide interface layer and back metallization on the CMOS-grade silicon, the interaction of electromagnetic fields with the lossy silicon substrate has been isolated, and as a result a low-loss and low-dispersive CBCPW line has been obtained. Measured attenuation constant at 20 GHz is below 1.2 ㏈/cm, which is compatible with the CPW on GaAs. In addition, by using the proposed CBCPW geometry, miniaturized BPF for Ku band application is designed and its measured frequency response shows excellent agreement with the predicted value with validating the performances of the proposed CBCPW geometry for RFIC interconnects and filter applications.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권5호
• /
• pp.682-686
• /
• 2016

A fully differential RC calibrator for accurate cut-off frequency of a programmable channel selection filter is proposed. The proposed RC calibrator consists of an RC timer, clock generator, synchronous counter, digital comparator, and control block. To verify the proposed RC calibrator, a six-order Chebyshev programmable low-pass filter with adjustable 3 dB cut-off frequency, which is controlled by the proposed RC calibrator, was implemented in a $0.18-{\mu}m$ CMOS technology. The channel selection filter with the proposed RC calibrator draws 1.8 mA from a 1.8 V supply voltage and the measured 3 dB cut-off frequencies of the channel selection LPF is controlled accurately by the RC calibrator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1016-1019
• /
• 1993

A low-pass L-C filter has been adopted for conversion of frequency variable 3 phase PWM waveform to a grid power line and it is used for attenuation of harmonics in the VSI PWM Inverter. A optimum design of the L, C parameters was derived. The result of the study show that the inductor L seems to have a certain air gap for linear I-V characteristics and the resonant frequency of the filter must be set below the 5th harmonics of the grid power line. Further, the voltage drop in L must be within a adequate limit compared to grid power voltage.

• 한국전자파학회논문지
• /
• 제23권3호
• /
• pp.355-360
• /
• 2012

본 논문에서는 계단 임피던스를 갖는 삼각패치형 5단 저역 통과 여파기를 제안한다. 제안된 구조는 일반적인 계단형 임피던스 저역 통과 여파기를 직각 이등변 삼각형으로 접어 구현한 구조로서, 설계법은 기존의 계단형 임피던스 여파기와 동일하다. 또한, 기존 계단형 임피던스 여파기와 다르게, 이 구조는 콤팩트하게 접히면서 생성된 slot들에 의하여 여파기의 차단 주파수 및 차단 대역폭과 감쇠극 특성을 조절할 수 있는 장점을 가지고 있고 또한, 소형화에 유리하다. 제작된 여파기는 $13.75mm{\times}6.875mm$의 크기로 일반적인 계단형 임피던스 여파기에 비해 24.4 %의 크기가 감소되었다. 측정 결과, 통과 대역에서 -10 dB 이하의 반사 손실과 차단 대역에서 -10 dB 이하의 삽입 손실을 보였고, 약 $3f_c$까지 차단되었다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권8호
• /
• pp.387-393
• /
• 2001

This paper describes an advanced measuring method and precise evaluation of the ground resistance for the grounding system of energized substations and power equipments. A grounding system of substations consists of all interconnected grounding connections of grounded conductors, neutral ground wires, underground conductors of distribution lines, cable shields, grounding terminals of equipments, and etc. It is very difficult to measure the accurate ground resistance of the grounding terminals of equipments, and etc. It is very difficult to measure the accurate ground resistance of the grounding system of high voltage energized substations because of harmonic components caused by switched power supplies or overloads. The conventional fall-of-potential method may be subject to big error if stray ground currents and potentials are present. In this work, to improve the precision in measurements of the ground resistance by eliminating the effects of harmonic components and stray currents and potentials, the investigations of the ground resistance measurement by using a low pass filter in a model energized grounding system were conducted. The accuracy of ground resistance mesurements was evaluated as a function of the ratio of the test signal to noise (S/N). The errors due to the proposed ground resistance measurement method were decreased with increasing S/N and were less than 5[%] as S/N is 10. The proposed ground resistance measurement method appears to be considerably more accurate than the conventional fall-of -potential method. It is allows cancellation of the parasitic resistance of energized grounding systems, to employ the measurement method that allows cancellation of the parasitic effects due to other circulating ground currents and ground potential rises in practical situations.

• 한국전자파학회논문지
• /
• 제26권11호
• /
• pp.960-965
• /
• 2015

본 논문에서는 인공전송선로 중 LUC(Low-pass filter Unit Cell) 구조를 이용한 결합선로 방향성 결합기를 제안한다. 일반적인 결합선로 결합기는 ${\lambda}/4$ 길이의 전송 선로를 사용하므로 소형화에 한계가 있다. 반면에 제안한 결합기는 $90^{\circ}$보다 아주 작은 두 결합선로 사이에 위상 지연선로를 삽입하여 전체적으로 $90^{\circ}$보다 작게 결합기를 구현했고, 일반적인 전송선로의 특성을 특정 주파수 내에서 만족하는 인공전송선로를 이용하여 결합기에 위상 지연선로를 구성함으로써 물리적 크기를 감소시켰다. 중심주파수 700 MHz에서 -10 dB의 결합량 특성을 갖는 방향성 결합기를 설계 및 제작, 측정하였다. 측정된 결과는 기존 결합기와 비슷한 성능을 보였다. 반면, 제작한 결합기의 결합선로는 기존 결합기의 약 45% 크기를 가지고 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.138-141
• /
• 2001

In this paper, a VBF(variable bandwidth filter) is suggested and analyzed in time-frequency domain. There are four kinds of VBF, which are low-pass VBF, high-pass VBF, band-pass VBF and band-stop VBF. The proposed VBF can extract the components of signals within variable instantaneous bandwidth at a specific time instant. Instantaneous bandwidth is estimated in time-frequency domain. The VBF is represented by rational form in extended Fourier frequency domain.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1673-1675
• /
• 2004

The design, modeling and measurement of RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a LTCC multi-layer switching circuit and integrated low pass filter. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.