• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.110-113
• /
• 2002

Organic EL has been expected to adopt to a new styles of technology that make flat display after Tang & Vanslyke made good electric luminescence device in late 1980s. Their studies based on multi layer structure that consists of emitting layer and carrier transporting layer using proper organic material. In this study. we made multi layer device using $Eu(TTA)_3(phen)$ as a luminescence material by PVD and investigate luminous properties of each device. But oxidization of organic layer by ITO. energy walls in both pole interface. contaminations of ITO surface, importance of protecting membrane, diffusive dimming of light to cathode organic layer. these causes of degradations are common facts of a macromolecule and micromolecule. We think these degradation caused by the impact of heat and electro-chemical factor, bulk effect and interface phenomenon. and raise a question.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.9-11
• /
• 2002

These days, electromagnetic radiation noise and switching losses of static converter become harmful. Many resonant inverters with radiation techniques solve their such problems. Auxiliary Resonant Commutated Pole Inverter (ARCP) was proposed. but it has two demerits. In circuit configuration. It isn't constructed by 2 in 1 IGBT modules, Besides, control is complicated because of neutral point voltage control and boost. current control. This paper proposes a new auxiliary resonant inverter which solved two demerits. In addition, it deals efficiency which compared with hard switching inverter and result of separation of power loss

• Journal of Power Electronics
• /
• v.9 no.1
• /
• pp.117-123
• /
• 2009

This paper presents a sliding mode observer for the sensorless control of interior permanent magnet synchronous motor (IPMSM) drives. The sliding mode observer has been presented as a robust estimation method. Most of these previous works, however, were not for an interior PMSM (IPMSM), but for a non-salient pole PMSM and its observer design is conducted in the stationary reference frame. Thus, in this paper, we investigate the design of a sliding mode observer and its driving characteristics for an IPMSM. The proposed sliding mode observer is designed in the rotating reference frame, and good drive performance is achieved even when the observer parameters are mismatched with those of an actual motor. The proposed method is applied to a 600W IPMSM, and, then, the measurement results are presented.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1474-1475
• /
• 2006

This paper describes touch and step voltage in the reinforced concrete and steel poles. Ground surface potential rises were measured as a function of the separation between pole and ground rod. Touch and step voltage are calculated on the basis of the distribution of ground surface potential rises. As a result, touch and step voltages strongly depend on the position of installation of ground rod.

• Proceedings of the KIEE Conference
• /
• 1996.07b
• /
• pp.980-983
• /
• 1996

This paper presents the method of determining state feedback gains of XPTOS for disk drive servomechanism based BESSEL filter prototype. A typical disk drive actuator can be modeled as second order dynamics for low frequencies. However, the response at higher frequencies shows resonant behavior which cannot be easily modeled. XPTOS consists of the nonlinear control region and the linear control region. In the linear control region, the poles of a second order nominal model of plant must be properly relocated by pole placement technique to attenuate resonant modes at high frequency and to attain minimum time state transition. It is difficult to select position to satisfy this object because velocity feedback gain is subjected to position feedback gain in XPTOS. Here poles of BESSEL filter prototype are selected to determine state feedback gains of XPTOS. Simulation results for disk drive servomechanism using XPTOS having state feedback gains by the proposed method are presented.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.271-273
• /
• 1993

One maglev vehicle is composed of 6 or 8 modules. Each module is composed of 4 staggered magnets attached to an aluminum bogie. In the view point of levitation control except propulsion-by LIM. 5 is the maximum degree of freedom to be controlled. But rolling control of the vhhicle depends on the bogie structure. We describe just anti-roll type bogie structure and 4 degree of freedom control is sufficient for levitation quality improvement. Multivariable pole-placement concept is used for controller design. Control experiment is performed on a specially designed test module as well as actual bogie system.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.293-295
• /
• 1993

Most control system design problems involve finding state feedback gain for good response by the pole or characteristic polynomial assignment. In this paper, the characteristic polynomial assignment using PID controller for discrete 2-dimensional system descrived by the Fornasini-Marchesini's 2nd model (F-MM II) is considered. This method it not only available to F-MM II but also to Rosser's model.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.136-138
• /
• 2009

A new class of electronically commutated brushless motor, the flux-switching motor(FSM) is gradually emerging in power tools and household appliances especially fan application. This motor offers advantages of both high-power density and relatively high efficiency This paper presents the principle of the FSM and design of the 12/6 pole FSM drive system. Finally, test results of the prototype motor are provided to verify a validity of the fan application.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.55-57
• /
• 2009

This paper deals with an improved core loss calculation under the load conditions, namely, no-load, AC-load and DC-load of multi-pole PM generator from curve fitting method using modified Steinmetz equation considered anomalous loss. For an accurate calculation, magnetic field analyses in stator core considering the time harmonics are performed. And using the nonlinear finite element analysis (FEA), we applied separated rotating and alternating magnetic field to core loss calculation. In order to verify the core loss results by proposed method, the experimental system for no-load core loss measurement has been implemented with DC motor, power analyzer and manufactured PM generator. And, the analysis results with rotational speed agree extremely well with those obtained by measurement.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1230-1231
• /
• 2007

2MW 풍력발전기용으로 사용할 영구자석형 동기발전기 물리설계 과정을 설명하다. 기어비가 72.28인 3단 기어를 사용하여 영구자석 pole을 회전자 표면에서 3 mm 깊이로 삽입시켜 안정된 구조를 취했다. 토크, 인덕턴스, 유기전압, 손실, 온도분포 등을 계산하기 위해 전자기해석과 열해석 등을 통해 영구자석, 회전자, 고정자 등의 구조를 정하고와 크기를 최적화시켰다.