• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.447-452
• /
• 2001

An automated system is developed to perform fatigue crack growth tests under constant effective stress intensity factor range ${\Delta}K_{eff}$. In the system, crack length and crack opening load are measured in real-time by using the unloading elastic compliance method. The system consists of two personal computers, an analogue electrical subtraction circuit, a stepping motor, a stepping motor driver, a PIO board, and the application software used to integrate the whole system. The performance of the developed system was tested and discussed performing constant ${\Delta}K_{eff}$ crack growth tests on a CT specimen of 7075-T6 aluminum alloy. The performance of the system is found to be strongly dependent on the accuracy of measurements of crack opening load. Besides constant ${\Delta}K_{eff}$ testing, the system is expected to be successfully applied for automation of various fatigue tests.

• Journal of the Korean Society of Safety
• /
• v.32 no.6
• /
• pp.22-28
• /
• 2017

According to the National Fire Data System (NFDS), more than 5,000 vehicle fires have occurred every year for the last 10 years. Vehicle fires are primarily caused by mechanical (breaking system and engine), electrical (wiring and battery), and chemical (oil and fuel gas leakage) problems. The electrical factor has increased with the installation of driver convenience equipment. For example, today, the black box is widely used to provide video data recording of motor vehicle accidents. The black box consists of a front camera, rear camera, and wires. The black box wires are directly connected to the junction box or fuse box from the start battery that operates to provide normal on power supplying for engine stop. It is extremely dangerous when the wires short circuit due to insulation aging, mechanical and electrical stress, etc. In this study, the black box wiring fire risk have been analyzed and investigated when the steady state and abnormal operations, and under the following conditions: wiring arrangements with a high temperature condition, insulation aging, poor contact, and short circuits. The results showed that black box wiring short circuits had a higher fire risk than the other fire hazard elements. To prevent fire hazards caused by black box wiring, the black boxes must be installed by qualified service personnel. Do not modify the wiring, remove the fuse and secure the wiring using cable ties or insulation tape.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.912-914
• /
• 2002

Single phase SRM(Switched Reluctance Motor) can not be started by itself and torque ripple is more generated than multi-phase SRM. But it is excited by single phase current and has very simple structure. Therefore it can be used in domestic appliance. Torque and speed of single phase SRM is controlled by adjusting exciting current and exciting section. Driver, which is composed with absolute encoder and DSP, is fabricated for control of exciting section on this paper. Then driving characteristics with exciting section is confirmed by using salient pole rotor type single phase SRM, which is fabricated in preceding research.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.278-281
• /
• 2000

In this study, the electrical characteristics of 100V -Class LDMOSFET for high temperature applications such as electronic control systems of automobiles and motor driver were investigated. Measurement data are taken over wide range of temperature(300K-500K) and various drift region length(6.6$\mu\textrm{m}$-12.6$\mu\textrm{m}$). In high temperature condition(>450K), drain current decreased over 50％, and specific on-resistance increased about twice in comparison with room temperature. Moreover the ratio R$\sub$on//BV, a figure of merit of the device, increased with increasing temperature.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.101-103
• /
• 2003

This paper presents the speed control of Brushless DC Motors using PI control. PI control is implemented by software using digital signal processor(DSP) TMS320F240 from Texas instruments. Considering the cost of BLDC Driver A. B. C phase hall IC's signal is used instead of incremental encoder. The Present paper describes, how to control a speed of BLDC Drive.

• Proceedings of the KIEE Conference
• /
• 2000.11a
• /
• pp.232-235
• /
• 2000

Design and experiments of a nondestructive system to inspect deterioration of ACSR-OC (ACSR Outdoor Cross-linked Polyethylene Insulated Wire usually used in HV overhead distribution lines presented in this paper. ACSR-OC conductor built to pollutants air for a long period would be easily progress to corrode so that it may lead to the reduction of the effective cross section area of conductors. A fault diagnosis system consisting of a solenoid sensor, a constant current source with RF frequency signal processing unit and a motor driver/controller designed and implemented. This instrument can dot the sensor output variation due to deterioration corrosion, continuously. As a result, it was shown such corrosion detector can readily be utilized estimating the diameter change due to deterioration overhead distribution lines and in giving an warning or inform before severe aged conductor lead to fail.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.13-16
• /
• 2002

In this study, the electrical characteristics of 100v-Class LDMOSFET for high temperature applicat -ions such as electronic control systems of automo -biles and motor driver were investigated. Measurement data are taken over wide range of temperature(300k-SOOK) and various gate length(1.5 #m-3.0#m, step 0.3). In high temperature condition(>500k), drain current decreased over 30%, and specific on- resistance increased about three times in comparison with room temperature. Moreover, the ratio ROJBV, a figure of merit of the device, increased with increasing temperature.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.287-289
• /
• 1995

In this paper, We applied the $\mu$-stepping method on the Phase Excitation Sequence of Hybrid type LPM. Linear Pulse Motor can opeate in an open loop control as an effective positioning actuator. PWM driver was used for low power loss and automatically adjusted voltage at rate current. Finally we find that through the position-velocity for timing Triangular and Trapezoidal Profile are very affected by velocity and acceleration parameter.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1429-1430
• /
• 2015

The present study developed an air flow generator system with standard syringes usually adapted for spirometer calibration. It consisted of servo-motor, driver, linear robot, and controller operating as a whole integrated system capable of generating air flows at different speeds on two identical 3L syringes. Experiments demonstrated high accuracy in both flow and volume generation as required such that relative errors were approximately 2.1% and 0.5%, respectively.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.93-97
• /
• 1988

The sliding mode control is an effective method to establish robustness against parameter variations and disturbance. But, in sliding mode strategy, the control function is discontinuous on the hyperplane. Consequently, the control input chatters at high frequency. When we apply such a control to the induction motor drive system, that causes a torque ripple and current harmonics, which are harmful to the system. In this paper, we introduce a low pass filter between sliding mode control output and driver input to overcome that problem. The band-width of this filter is varied according to the error funtion to improve transient responses.