• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1342_1342
• /
• 2009

Zinc tin oxide (ZTO) based thin-film transistors (TFTs) were fabricated on glass substrate by using sol-gel method. The fabricated ZTO TFT had bottom gate and top contact structure with ZTO layer formed by spin coating from ZTO solution. The fabricated TFT showed field-effect mobility of about 2 - $4\;cm^2/V{\cdot}s$ with on/off current ratios >$10^7$, and threshold voltage of 2 V.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1525_1526
• /
• 2009

In this paper, we have studied the bulging phenomenon of ink-jet printed silver lines. The used silver inks are DGP-40LT-15C and DGH-55HTG of Advanced Nano Product (ANP) Company. We investigated the behavior of bulging by changing the polarity of the inks, the surface energy of substrate and droplet spacing in printing. The contact angle of the polar inks increased much more sensitively than the nonpolar ink as the surface energy of the substrate increases. In the case of the nonpolar ink, the bulging phenomenon occurred seriously as the droplet spacing decreased at the constant surface energy.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2049_2050
• /
• 2009

본 연구에서는 수소 연료전지의 엔드플레이트와 외부 연결 부분의 금속을 진동시험기를 이용하여 접촉저항을 측정하였다. 수소 연료전지의 집접판에서의 전류밀도의 변화와 온도 분포의 변화를 비교해 볼 수 있었으며, 접촉저항을 측정 할 수 있었다. 진동시험기는 5~50 Hz의 범위까지 설계하였으며 진동에 대한 접촉저항의 변화도 확인 할 수 있었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.4
• /
• pp.121-128
• /
• 2001

This study has been performed to investigate formability of non-vinyl PCM(pre-coated metal)sheet. First, physical test of PCM sheets were tested to evaluate finish coating characteristic of PCM. And then, test equipment was made for friction test and three non-vinyl PCM sheets were tested by straight pulling method. This paper provides the results of the friction tests showing the influence of sheet surface texture and process conditions. It was found that the influence of contact pressure and speed had an effect upon the level of friction. Also using tests, the scratch resistance of a series of polyester coating has been investigated. This investigation aims to clarify the process conditions that prevent the scratch of PCM to form the good electrical appliances such as microwave oven, air conditioner and refrigerator etc.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.346-353
• /
• 2001

In this study dynamic characteristic of catenary system that supplies electrical power to KTX Korean high-speed trains are investigated. A simulation program based on 3-span and 6-span finite element models of the catenary is developed. The influences of the various design parameters on the dynamic responses of the catenary are determined. The main design parameters include tension on the contact and messenger wires and the stiffness of the droppers connecting the two wires. The vibrational responses are primarily determined by the reflections of the propagating wave, and the dropper stiffness is found to be the dominant factor that influences overall dynamic characteristics of the catenary.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.600-600
• /
• 2013

We have fabricated Cr nanodot Schottky diodes utilizing AAO templates formed on n-Si substrates. Three different sizes of Cr nanodots (about 75.0, 57.6, and 35.8 nm) were obtained by controlling the height of the AAO template. Cr nanodot Schottky diodes showed a rectifying behavior with low SBHs of 0.17~0.20 eV and high ideality factors of 5.6~9.2 compared to those for the bulk diode. Also, Cr nanodot Schottky diodes with smaller diameters yield higher current densities than those with larger diameters. These electrical behaviors can be explained by both Schottky barrier height (SBH) lowering effects and enhanced tunneling current due to the nanoscale size of the Schottky contact. Also, we have fabricated Cr-Si nanorod Schottky diodes with three different lengths (130, 220, and 330 nm) by dry etching of n-Si substrate. Cr-Si nanorod Schottky diodes with longer nanorods yield higher reverse current than those with shorter nanorods due to the enhanced electric field, which is attributed to a high aspect ratio of Si nanorod.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.89-90
• /
• 2007

Electrowetting 현상을 contact angle의 변화가 아닌 전자기 체적력의 관점으로 고찰한다. 정수역학의 방정식과 Kelvin 식, 표면장력 공식을 도입하고, 체표면의 모든 곳에서의 압력이 일정하다는 원리를 이용하여 유체 표면의 형상을 고찰한다. 액적의 초기 형상은 반원, 반지름은 1mm이다. 절연 처리한 판형태의 도체위에 액적을 올려놓고 그 액적에 핀을 꽃은 형태로 전계를 인가한다.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.211-213
• /
• 2007

Current of DC traction systems flows from the positive busbar of the substation, through the overhead contact system, to the vehicle, and returns through the running rails. Because the rails are not very effectively insulated from the earth a certain amount of current flows into the earth, especially in the area near the load and depots. At the place where the stray current leaves the rail and pipe, corrosion may take place. In this paper we introduce the electrolytic corrosion protection methods of depots using silicon rectifier for the rail.

• Proceedings of the KIEE Conference
• /
• 2007.11c
• /
• pp.93-96
• /
• 2007

In this paper, the testing equipment for evaluating aging characteristics of outdoor silicone rubber insulator resulting from the environmental aging effect with regards to sunlight(UV) was developed. Influence of sunlight effect aging is seriously increase due to destruction of ozone layer which is occurred by consumption of fossil fuel. For this purpose, silicone rubber was aged under the artificial sunlight by exposure of xenon lamp radiation in the accelerating aging chamber and various test and analysis were performed such as breakdown strength, contact angle. And FT-IR analysis has been followed.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.643-645
• /
• 2008

Stainless steel 304 and 316 plates were deposited with the multi-layered coatings of titanium film (0.1um) and gold film (1-2um) by an electron beam evaporation method. The XRD patterns of the stainless steel plates modified with the multi-layered coatings showed the crystalline phases of the external gold film and the stainless steel substrate. Surface microstructural morphologies of the stainless steel bipolar plates modified with multi-layered coatings were observed by AFM and FE-SEM images. The external gold films formed on the stainless steel plates showed microstructure of grains of about 100nm diameter. The grain size of the external surface of the stainless steel plates increased with the gold film thickness. The electrical resistance and water contact angle of the stainless steel bipolar plates covered with multi-layered coatings were examined with the thickness of the external gold film.