• Journal of the Korean Society for Railway
• /
• v.10 no.2 s.39
• /
• pp.112-116
• /
• 2007

In this paper, we proposed a selection and application recommendations of ZnO arresters for DC electric traction vehicles. To decide the Continuous Operating Voltage($U_C$), the Rated Voltage($U_r$), and the Nominal Discharge Current(In), we measured and analyzed system voltages and surge currents flowing the arrester installed on a DC electric traction vehicle under running state. System voltages measured up to 1,800 V in 1,500 V-system, and surge currents were recorded up to 3 times per a running-service-route and their magnitudes were ranges of $150A{\sim}2kA$. From these results and a standard EN50163, we could proposed $U_C$, $U_r$, and In available for the 1,500 VDC electric traction vehicles.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.4
• /
• pp.808-812
• /
• 2013

Multilayer capacitors with high ripple current and high capacitance were manufactured. The electrical properties of these capacitors were characterized for potential application for DC-link capacitors in hybrid electric vehicle inverters. Internal electrode structures were designed to achieve high capacitance and reliability. A single multilayer capacitor showed $0.46{\mu}F/cm^3$ of capacitance, 0.65% of dielectric loss, and 1450 V to 1650 V of dielectric breakdown voltage depending on the design of the internal electrode. The capacitor module designed with several multilayer capacitors gave a total capacitance of $450{\mu}F$, which is enough for hybrid electric vehicles. In particular, an equivalent series resistance of $4.5m{\Omega}$ or less will result in 60 $A_{rms}$, thereby reaching the allowed ripple current for hybrid electric vehicles.

• Journal of Power Electronics
• /
• v.3 no.4
• /
• pp.230-238
• /
• 2003

Electric vehicles (EV) demands for greater acceleration, performance and vehicle range in pure electric vehicles plus mandated requirements to further reduce emissions in hybrid electric vehicles (HEV) increase the appeal for combined on-board energy storage systems and generators. And the power electronics plays an important role in providing an interface between fuel cells (FC) and loads. This paper deals with a multiple input DC-DC power converter devoted to combine the power flowing of multi-source on energy systems. The multi-source is composed of (i) FC system as a prime power demands, (ii) super capacitor banks as energy storage devices for high and intense power demands, (iii) superconducting magnetic energy storage system (SMES), (iv) multiple input DC-DC power converter and (v) a three phase inverter-fed permanent magnet synchronous motor as a drive. In this system, It is used super capacitor banks and superconducting magnetic energy replaces from the battery system. The modeling and transient performance simulation is effective for reducing transient influence caused by sudden charge of effective load. The main purpose of power electronic converters is to convert the DC power output from the fuel cell and other to a suitable AC voltage, which can be connected to electric loads directly (PMSM). The fuel cell and other output is connected to the DC-DC converter, which regulates the DC link voltage.

• Journal of Magnetics
• /
• v.21 no.4
• /
• pp.537-543
• /
• 2016

Currently, an interest in electric vehicles (EVs) exhibited by automakers, government agencies and customers make it as more attractive research. This is due to carbon dioxide emitted by conventional combustion engine that worsens the greenhouse effect nowadays. Since electric motors are the core of EVs, it is a pressing need for researchers to develop advanced electric motors. As one of the candidates, switched flux machine (SFM) is initiated in order to cope with the requirement. This paper proposes a new alternate circumferential and radial flux (AlCiRaF) of permanent magnet switched flux machines (PMSFM) for light weight electric vehicles. Firstly, AlCiRaF PMSFM is compared with the conventional PMSFM based on some design restrictions and specifications. Then the design refinements techniques are conducted by using deterministic optimization method in order to improve preliminary performance of machine. Finally the optimized machine design has achieved maximum torque and power of 47.43 Nm and 12.85 kW, respectively, slightly better than that of conventional PMSFM.

• Korea Trade Review
• /
• v.47 no.5
• /
• pp.1-20
• /
• 2022

As a part of environmental pollution mitigation in China, the number of environmentally friendly vehicles in China is proliferating, attention to vehicles that use environmentally friendly energy continues to increase, and China's new energy vehicle market is also growing rapidly. Similar to existing research, the focus of the subsidy is to provide financial support for electric vehicle buyers and the expansion of new energy vehicle charging infrastructure. Under these circumstances, this study attempts to understand the influence of Chinese consumers' green responsibility and other psychological factors on electronic vehicle purchase intention based on norm activation theory and theory of planned behavior. PLS-SEM examined the proposed hypotheses with 369 valid Chinese consumers, and all were supported. Our findings contribute to the extension of the research scope of Chinese consumers' intention to purchase electric vehicles and provide practical information for domestic and foreign firms entering China, the world's largest electric vehicle market.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.105-110
• /
• 2009

The On Line Electric Vehicles(OLEV) that can pick up inductive power from underground coils on driving with high efficiency have been developed this year, and is now proposed in this paper. The IPS(Inductive Power Supply) system consists of power supply inverters, power supply rails, pick up modules, and a regulator. There are 3 generations of IPS have been developed so far, and the $4^{th}$ generation IPS is being developed. The $1^{st}$ generation has been demonstrated this Feb. 27, which is equipped with mechanically auto tracking pick-up module with 1cm air gap, and showed 80% power efficiency. The $2^{nd}$ generation IPS applied to an 120kW (average)/240kW(peak) motor powered electric bus has 17cm air gap with 72% power efficiency. For the $2^{nd}$ generation IPS, the Power supply inverter has 440V, 3phase input and 200A @ 20kHz output. The test power supply rail of 240m long is segmented by 60m each, where newly developed core structure and power cable are constructed under the road covered with asphalt of 5cm thickness. The pick-up modules which consist of core, winding wire, and rectifiers are fixed to the bottom of the bus which can carry more than 40 passengers and can pick up max. 60kW. To remove parasitic component and to transfer maximum power between them resonant circuit topology is applied to the primary and secondary sides. The EMF level is below 62.5mG at 1.75m from the center of the road to meet the regulation. Several effective ways of reducing EMF levels have been developed. In addition, effective ways to solve problems related high frequency power cables buried in ground and it's proof from soil have been studied also. This development shows that the IPS system is capable of supplying enough power to the pick-up of OLEV and can reduce battery size, weight and cost, which means the IPS with OLEV is one of the best candidate for EV.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.873_874
• /
• 2009

This paper presents a method for designing a high power motor that is applicable to electric vehicles. Interior Permanent Magnet (IPM) type motor which has high efficiency and high durability is selected. To apply for the electric vehicles, a form, a tire and a wheel of vehicles are considered when calculating a motor performance. After calculating a motor performance, space harmonic analysis and FEA(Finite Element Analysis) is used for designing In-Wheel motor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.209-220
• /
• 1996

In this paper, dynamic performance of 4WD/4WS Electric-driven vehicles is investigated. A coupled dynamic model is introduced for longitudinal, lateral and yawing motion of 4WD/4WS vehicles. Based on the coupled model, dynamic performance is analyzed for steady-state steering, acceleration steering and brake steering, respectively. These non steady-state cornering analysis is important for non-paved road maneuvering, trajectory projection for armored vehicle and future AVCS(Advanced Vehicle Control System) technology. Simulation results are obtained based on a simulink module for the introduced model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.29-38
• /
• 1997

In this paper, brake steering performance of electric-driven special-purpose vehicles is investigated. A 14 DOF model is developed considering nonlinear character- istics of the suspension and tire. Based on the model, cornering performance is analyzed for brake steering, acceleration steering and pivoting, respectively. Simulation results are obtained based on the developed SIMULINK module. This analysis about the non steady state cornering performance is particularly important for armored vehicles because the projected route of the vehicle at emergency should be predicted accuracy.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.511-513
• /
• 2005

The fuel cell system has inherent limitation such as slow response time and low fuel economy especially at the low power region, and thus, the battery system has come to be used to compensate for the fuel cell system. This type of hybrid configuration has many advantages, however, the energy management strategy is essentially required. The work in this paper presents survey on recent power management strategies for fuel cell hybrid electric vehicles. For three power management strategies: basic control method. object function-based control method, and fuzzy logic-based control method. each strategy is reviewed and discussed with other strategy.