• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2190-2192
• /
• 2005

Discharge of the flat lamp lighting source research are requested very much. For improving brightness, life time, efficiency of flat lamp, plasma diagnosis of the flat lamp lighting source to understand property of lighting source is very important. distance of discharge electrode is 5.5mm and width is 16.5mm, we measured electron temperature and electron density measured with single langmuir probe in flat lamp. we tested the discharge from 100 Torr to 300 Torr pressure. the Pulse is rectangular pulse with frequency 20kHz and Duty ratio 20%. Resultly, electron temperature decreases and electron density increase as increase the gas pressure and electron temperature decreases and electron density increase as increase the voltage.

• Journal of Sensor Science and Technology
• /
• v.24 no.5
• /
• pp.348-352
• /
• 2015

Thin nickel oxide films formed on uncooled and cooled $SiO_2/Si$ substrates using a radio frequency (RF) magnetron sputter powered by 200 W in a mixed atmosphere of argon and oxygen. Grazing-incidence X-ray diffraction and field emission scanning electron microscopy are used for the structural analysis of nickel oxide films. The electrical conductivity required for better bolometric performance is estimated by means of a four-point probe system. Columnar and (200) preferred orientations are discovered in both films regardless of substrate cooling. Electric resistivity, however, is greatly influenced by the substrate cooling. Oxygen partial pressure increase during the nickel oxide deposition leads to a rapid decrease in resistivity, and the resistivity is higher in the cooled nickel oxide samples. Even when small microstructure variations are applied, lower resistivity in favor of low noise performance is acquired in the uncooled samples.

• Journal of Surface Science and Engineering
• /
• v.50 no.5
• /
• pp.373-379
• /
• 2017

Dry processes like evaporation and sputtering in vacuum chamber are difficult to make a uniform, large area and high quality film on thin PET substrate because of PET degradation and bad adhesion. On the other hand, wet processes like electro or electroless plating have complex processes and require high environmental cost. In this study, we successfully prepared $2{\mu}m$ Zn/Cu/Ni multilayers coated on $12{\mu}m$ polyethylene terephthalate (PET) substrate by using dry-wet mixing processes. Their surface electric resistances were evaluated around $0.2{\Omega}$ by using 4 probe measurements. Furthermore, their corrosion resistance also evaluated by natural potential test and compared with other wet, dry and mixing process samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.3-4
• /
• 2007

Orientational ordering of polar molecules and excess charges at the interface are main origins of surface polarization. For organic electronics, probing and control of these two surface polarization phenomena are key issues. In this presentation, I report a novel electrical measurement that can directly probe orientational dipolar motion in surface monolayers by Maxwell-displacement-current, and also report a novel optical technique that allows carrier motions in organic materials by measuring the optical second harmonic signals activated by the electric field. Then I discuss how the control of dipolar motions and carrier motions are linked to organic electronics applications such as organic field effect transistors.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1637-1639
• /
• 2005

The measurement of magnetic field is performed about DC and AC magnetic field in test track of depot. The test point is cap, on the converter/inverter box, on the traction motor, on the APSE and on the line filter, the height of measurement is bottom and 50 cm height. In case of AC magnetic field, the selected specific frequency is measured on the converter/inverter box. The AC magnetic field is checked and analysis through RS-232C and notebook PC. The DC magnetic field is measured by using the Hall Probe, test result is saved and analysis by PXI system. On the line filter, the maximum value is 1.4 mT in case of DC magnetic field and 0.044 mT in case of AC magnetic field at 50 Hz.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.98.2-98.2
• /
• 2013

Electrochemical phenomena underpin a broad spectrum of energy, chemical, and information technologies such as resistive memories and secondary batteries. The optimization of functionalities in these devices requires understanding electrochemical mechanisms on the nanoscale. Even though the nanoscale electrochemical phenomena have been studied by electron microscopies, these methods are limited for analyzing dynamic electrochemical behavior and there is still lack of information on the nanoscale electrochemical mechanisms. The alternative way can be an atomic force microscopy (AFM) because AFM allows nanoscale measurements and, furthermore, electrochemical reaction can be controlled by an application of electric field through AFM tip. Here, I will summarize recent studies to probe nanoscale electrochemical reaction in battery applications by AFM. In particular, we have recently developed electromechanical based AFM techniques for exploring reversible and irreversible electrochemical phenomena on the nanoscale. The present work suggests new strategies to explore fundamental electrochemical mechanisms using the AFM approach and eventually will provide a powerful paradigm for probing spatially resolved electrochemical information for energy applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.4-4
• /
• 2010

박막의 물성을 분석하는 방법에는 광학을 이용한 분광학 분석법과 나노크기의 tip을 이용한 나노트라이볼로지 분석법이 대표적이라 할 수 있다. 분광학 분석법에는 주로 X-ray 회절분석, Raman 분광기, IR 분광기 등등이 가장 대표적으로 사용되어지는 분석 장치들이다. 이러한 분광학 분석은 광학을 시료에 조사하여 이로부터 획득되는 강도(intensity)를 분석하는 방법으로 간접적인 분석이라 할 수 있다. 이에 반하여 나노트라이볼로지는 나노크기의 tip을 이용하여 시료 표면을 직접적인 방법으로 분석하여 시료의 형상, 탄성, 강도, 마찰력 등의 정보를 제공하며, tip에의 전기적 신호를 부과하여 시료 표면의 국부적인 potential, electric current를 측정하게 된다. 이에 해당되는 대표적인 분석 장치로는 nano-indenter system과 SPM (Scanning Probe Microscopy)이 있다. 따라서, 이 논문에서는 나노트라이볼로지의 대표적인 장치인 nano-indenter system과 SPM에 대한 간단한 원리를 소개하고 다양한 분야에 대한 실제적인 분석을 사례를 통하여 나노트라이볼로지의 가치를 확인하고자 한다.

• The Journal of Society for e-Business Studies
• /
• v.18 no.1
• /
• pp.71-95
• /
• 2013

This study aims to validate the cost of building the infrastructure to commercialize online electric vehicles. For that purpose, we probe the cost to construct the necessary infrastructure for online electric vehicles regarding Seoul area public bus transit. OLEV and PEV are considered as alternative electric vehicle schemes, and each of them has their own cons and pros in terms of rechargeable battery cost and charger cost. An optimization model which minimizes the cost to install online electric bus feeding devices is proposed in order to compare the total costs of the two alternative schemes. We developed a Mixed Integer Programming model to locate the feeding devices of several different lengths at each bus stops. Furthermore, we implemented a computer simulator to obtain the parameters which will be used in the MIP model and a Web-based system which determines the optimal location of infrastructure for the whole city area from a result of the MIP model. The cost comparison result shows that the total cost of OLEV is cheaper than that of PEV considering the real data of Seoul area public transit, and, as a result, confirms the feasibility of the commercialization of OLEV.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.430-434
• /
• 2010

The sheet for electromagenetic interference (EMI) shielding was prepared with slurry made by the mixture of binder, methyl ethyl ketone, cyclohexanone and metal powder. We tried to enhance the shielding efficiency by adding carbon nanotube (CNT), which has known as highly conducting material. Surface and component analyses were carried out with SEM and EDS, respectively. The electric characteristics and EMI shielding efficiencies were measured with 4-point probe measurement and EMI efficiency measurement equipment. The sheet with 2% CNT addition showed the lowest electrical resistance, $13.13{\Omega}}{\cdot}cm$. It also showed the highest EMI shielding efficiency of 63 dB.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.475-479
• /
• 2003

Traditional ultrasonic evaluation to detect micro/small surface cracks is the pulse-echo technique using the normal immersion transducer with high frequency, or the angle beam transducer with surface wave. It is difficult to make the automatic ultrasonic system that is to detect micro and small surface crack and position on the large structure like steel and ceramic rolls, because of the huge data of inspection and the ambiguous position data of transducer. The aim of this study using the high precision scanning acoustic microscope with 10MHz large aperture transducer was to display the real time A, B, C-scan for the automatic ultrasonic system in order to detect the existence and position of surface crack. The ultrasonic method with large aperture transducer was improved the scanning time and speed over 10times faster than traditional methods.