• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.93-96
• /
• 2007

This paper presents a theoretical approach to describe the vibration characteristics in the 1-3 piezoelectric composite arrayed on a cylindrical surface. By homogenizing the composite composed of a piezoelectric ceramic and a polymer the physically useful parameters were defined and then used to derive the governing equation of radial motion for the cylindrical 1-3 piezoelectric composite. Applying mechanical and electric boundary conditions has yielded a characteristic equation for radial vibration of the composite. Theoretical calculations of the resonance frequency have been compared with those obtained by the finite-element analysis and have shown a good agreement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.35-40
• /
• 1997

As demand of electric power are growing and transmission line limited owing to enlargement of the downtown area The eonfidence of underground transmission cable which shows gradual growth are high. It is found whether insulating ability is good or not. In this paper, The exper iment result is shown that the fall of insulating ability and take preventive measure through the analysis of tans, water content, dielectric breakdown voltage, total acid number, volume resistivity , and gas in the oil in an accordance with the characteristic change of oil used very much for insulating oil of cable.

• Electrical & Electronic Materials
• /
• v.9 no.5
• /
• pp.483-489
• /
• 1996

Power transformer have many unsymmetrical structure and electric field is enhanced in that area. Those unsymmetrical area are not covered oftenly by solid insulating material which is used as a framework specially in gas transformer. By that result there is a possibility to decrease the total insulation class of the transformer. So in this study the electrical characteristic of $FC+SF_6$ mixture gas which is used as coolants for large power gas insulated transformer and its effects on electrical characteristics of structural material are investigated. Also breakdown characteristic with the tension of taping and curvature of the coil are studied which could be used as a design factor of large power transformer.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.666-668
• /
• 2001

In this paper we are to explain the development of circuit breaker characteristic tester for 25.8kV Gas Insulated Switchgear. Because of hermetically sealed cubicle, we have the difficulties of installation and usage of tester. Therefore we developed measuring tester and software. This tester can measure CB close/trip time, coil current, stroke, chattering time. And it has CB positive/ negative discrimination program, trend management program, DB management program.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.2
• /
• pp.200-206
• /
• 2006

An electric power efficiency of electrodeless fluorescent lamp depens on a big relative property of gas, gas pressure, lamp formation, ingredients of magnetic substance and shape and action frequency etc. in lamp. We used magnetic substance that opens self-examination material of electrodeless fluorescent lamp antenna. We used Mn-Zn type as the Ferrite. We have examined resistance, impedance and Q-factor's frequency characteristic by ferrite. Coil turns were changed from 13 to 15 turns to recognize brightness change of lamp by winding number. Optical equipment (LS-100) was used to measure brightness. We could know Q-factor's difference according to material is important part of antenna design. When an electrodeless fluorescent lamp was made using T company's PE22, it showed the highest brightness. As number of winding is increased the brightness increased, and starting characteristic became good.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2017.10a
• /
• pp.88-92
• /
• 2017

As the considerable request of the fast and accurate way of the selection of circuit breaker is increased, we introduce the development of software of circuit breaker selection for the marine use. Originally, the selection of circuit breaker has been carried out by manual in the marine project. It is not the easy work to select the proper type of circuit breaker to check the time-current characteristic curves of each type of circuit breakers for the various type of loads. In this regards, we developed the software to select the proper type of circuit breaker to confirm fast and accurately. And, we introduce the course of the development of the software for the selection of circuit breaker.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.6
• /
• pp.1109-1114
• /
• 2003

In this paper, the electric characteristic of the SGPS with slot in the ground plane is similar to the parallel resonant circuit. When the slot length in SGPS is equal to the half wavelength of specific frequency, the characteristic of SGPS represent the large attenuation at the specific frequency. We found out the relation between attenuation and resistor on the slot in SGPS and we designed the variable attenuator for MMIC using the variable resistor. This attenuator can be applied to AGC circuit in transceiver if the PIN diode is used replace for resistor.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.2
• /
• pp.1-7
• /
• 2003

Nowadays, one of the serious problems in KEPCO(Korea Electric Power Co-Operation) system is the more higher fault current than the SCC(Short Circuit Capacity) of circuit breaker. There are many alternatives to reduce the increased fault current such as isolations of bus ties, enhancement of SCC of circuit breaker, applications of HVDC-BTB(High Voltage Direct Current-Back to Back) and FCL(fault current limiter). But, these alternatives have some drawbacks in viewpoints of system stability and cost. As the superconductivity technology has been developed, the HTS-FCL(High Temperature Superconductor -Fault Current Limiter) can be one of the attractive alternatives to solve the fault current problem. Under this background, this paper presents the EMTDC(Electro-Magnetic Transient Direct Current) model for resistance type HTS-FCL considering the nonlinear characteristic of final resistance value when quenching phenomena occur.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.173-173
• /
• 2010

We proposed viewing angle switchable liquid crystal display(LCD) associated with fringe-field switching (FFS) mode with high aperture ratio characteristic. In the device, single pixel is separated into two regions, named as main pixel for displaying images and sub pixel for viewing angle control. In sub pixel region, add the common electrode on the top substrate and the initial alignment of liquid crystal is Hybrid Alignment Nematic (HAN) state. In conclusion, we suggested that the device has high aperture ratio characteristic because the LC directors are rotated in which viewing angle control region are generated fringe electric field.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.137-140
• /
• 2003

Recently, as the demand of small-sized precision parts is rising in precision industry such as mobile, automobile, optic. etc. the requirement of small-sized machine tool is increasing. Desktop machine tool define small-sized machine tool that is able to install in table. According to diminishing in size, Desktop machine tool is able to economize production cost by reducing work area and consuming electric power. But Desktop machine tool generates vibration in acceleration and deceleration modes by inertia force of moving part. Also vibration is generated when it move simultaneously two axis or three axis. Such generating vibration situation is reason of declining stiffness of machine tool structure because of smallizing in size. And this vibration has a large effect on precision of machining products. Therefore, evaluating of the control characteristic is necessary for minimizing vibration of machine tool as much as possible to accomplish precision machining of small-sized parts