• Journal of Electrical Engineering and Technology
• /
• v.12 no.6
• /
• pp.2307-2316
• /
• 2017

The aim of this paper is to provide an optimal design of in-wheel motor for an electric scooter (E-scooter) considering economical production. The preliminary development in-wheel motor, which has a direct-driven outer rotor type attached to the E-scooter's rear wheel without any gear, is introduced first. The objective of the optimal design of this in-wheel motor is to improve the output characteristics of the motor and to have a stator form to facilitate automatic winding. Response surface methodology was used for the optimal design and 2-dimensional finite element method was used for electro-magnetic field analysis. Experimental results showed that the designed and fabricated in-wheel motor could satisfy the required specifications in terms of speed, power, efficiency, and cogging torque.

• International journal of advanced smart convergence
• /
• v.11 no.2
• /
• pp.219-225
• /
• 2022

Recently, the popularization of personal mobility(PM) has made it possible to see many electric scooters. The energy source of personal transportation used by the general public and the disabled can be seen as environmentally friendly as electricity. Personal transportation means are divided into small electric vehicles because they use electric energy, and they are being treated as new models by automobile manufacturers in each country and spurring development. On the other hand, personal transportation means may cause various types of traffic accidents as they travel between roads and a human walk. In order to prevent such accidents, it is judged that the enactment of laws on the establishment of specifications for electric scooters, which are personal transportation means, and the method of restricting road operation should be given priority. The electric scooter is basically different from the conventional vehicle. The steering shaft of the steering system applied to the electric scooter one to two is possible. 1 to 2 the front-wheel under the steering column is used. It is classified according to the number of wheel installed at the electric scooter is the vehicle body into 2 wheel - electric scooter, and 3 wheel - electric scooter and 4 wheel - electric scooter. In this study, we propose a steering shaft design model that can be applied to an electric scooter, one of personal transportation means. A design model for 1-shaft steering and 2-shafts steering that can be applied to electric scooters is proposed. In addition, we have produced the prototypes for the commercialization of the proposed models, and reviewed the pros and cons of the manufactured prototypes and models.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1366-1370
• /
• 2005

As the development of microprocessor technology, electric power steering (EPS) system which uses an electric motor came to use a few years ago. It can solve the problems associated with hydraulic power steering. The motor only operates when steering assistance is needed, so it can save fuel and can reduce weight and cost by eliminating hydraulic pump and piping. As one of performance criteria of EPS systems, the transmissibility from road wheel load to steering wheel torque is considered in the paper. The transmissibility can be studied by fixing the steering wheel and calculating the torque needed to hold the steering wheel from road wheel load. A proportion-plus-derivative control is needed for EPS systems to generate desired static torque boost and avoid transmissibility of fluctuation. A pure proportion control can't satisfy both requirements.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.750-755
• /
• 2013

In-wheel motor system gets the driving force from direct-driven motor in the wheel of electric vehicle. It is known as good system for vehicles, from an efficiency, packaging, handling and safety. This paper describes motor and inverter technologies, system configuration and control algorithms for in-wheel type electric vehicle. It is necessary to control on an interrelation perspective because this system drives two motors at same time. In system design, IPMSM(Interior Permanent Magnet Synchronous Motor) including a wide operating range and high-speed rpm is used and flux weakening control is performed in constant power range. Under the torque command from the host controller, auto control box, inverter's output torque is calculated with using torque estimation technique and applied to actual vehicle driving system. It is verified that the configuration and the algorithm are suitable for the in-wheel motor system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.1
• /
• pp.45-55
• /
• 2013

With the recent advancement of control method and battery technology, the electric vehicle have been researched to replace the conventional vehicle with electric vehicle with the view point of the environmental concerns and energy conservation. An electric vehicle which is equipped with the independent front steering system and in-wheel motors has advantage in terms of control. For example, the different torque which generated by left and right wheels directly can make yaw moment and the independent steering using outer wheel control is able to reduce the sideslip angle. Using of independent steering and driving system, the 4 wheel electric vehicle can improve a performance better than conventional vehicle. In this paper, we consider the method for improving the cornering performance of independent front steering system and in-wheel motor used electric vehicle with the compensated outer wheel angle and direct yaw moment control. Simulation results show that the method can improve the cornering performance of 4 wheel electric vehicle. We also apply the steering motor failure to steer the vehicle turned by the torque difference without steering. This paper describes an independent front steering and driving, consist of three parts; Vehicle Model, Control Algorithm for independent steering and driving and simulation. First, vehicle model is application of TruckSim software for independent front steering and 4 wheel driving. Second, control algorithm describes the reduced sideslip and direct yaw moment method in view of cornering performance. Last is simulation and verification.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.530-543
• /
• 2013

This paper describes a control scheme of speed sensorless fuzzy direct torque control (FDTC) of permanent magnet synchronous motor for electric vehicle (EV). Electric vehicle requires fast torque response and high efficiency of the drive. Speed sensorless FDTC In-wheel PMSM drives without mechanical speed sensors at the motor shaft have the attractions of low cost, quick response and high reliability in electric vehicle application. This paper presents a new approach to estimate the speed of in-wheel electrical vehicles based on Model Reference Adaptive System (MRAS). The direct torque control suffers in low speeds due to the effect of changes in stator resistance on the flux measurements. To improve the system performance at low speeds, a PI-fuzzy resistance estimator is proposed to eliminate the error due to changes in stator resistance. High performance sensorless drive of the in-wheel motor based on MRAS with on line stator resistance tuning is established for four motorized wheels electric vehicle and the whole system is simulated by matalb/simulink. The simulation results show the effectiveness of the new control strategy. This proposed control strategy is extensively used in electric vehicle application.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.567-573
• /
• 2012

Outer rotor type in-wheel Blushless DC Motor(BLDCM) for three-wheeled electric vehicle is researched. In-wheel system is to drive the electric vehicle without mechanical transmission, shaft, differential gears or other mechanical system. The motor is designed considering the performance requirements and drive modes of the vehicle. The determined dimensions as well as the slot and rotor pole are simulated by magnetic and thermal finite element analysis and ansys workbench to analyze the performance and heating of the motor. In order to verify the performance characteristics of the proposed motor, the experiment tests are executed and satisfy well the requirements.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.309-314
• /
• 2011

Outer rotor type in-wheel switched reluctance motor for Welfare neighborhood electric vehicle is researched. In-wheel system is to drive the electric vehicle without mechanical transmission, shaft, differential gears or other mechanical system. To calculate drive power for each wheels, the elder's and disable's safety driving conditions are considered. The designed outer rotor SRM has a 6-stator and 8-rotor pole. The determined dimensions as well as the stator and rotor pole arc are simulated and tested with CAD and finite element analysis to verify the performance of the proposed motor.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1483-1488
• /
• 2005

As the development of microprocessor technology, electric power steering(EPS) system which uses an electric motor came to use a few years ago. It can solve the problems associated with hydraulic power steering. The motor only operates when steering assistance is needed, so it can save fuel and can reduce weight and cost by eliminating hydraulic pump and piping. As one of performance criteria of EPS systems, the transmissibility from road wheel load to steering wheel torque is considered in this paper. The transmissibility can be studied by fixing the steering wheel and calculating the torque needed to hold the steering wheel from road wheel load. A proportion-plus-derivative control is needed for EPS systems to generate desired static torque boost and avoid transmissibility of fluctuation. A pure proportion control can' satisfy both requirements.

• Journal of the Korean Society for Railway
• /
• v.8 no.3
• /
• pp.216-221
• /
• 2005

In electric motor coaches, the rolling stocks move by the adhesive effort between rail and driving wheel. Generally, the adhesive effort is defined by the function of both the wright of electric motor coach and the adhesive effort between rails and driving wheel. The characteristics of adhesive effort is strongly affected by the conditions between rails and driving wheel. When the adhesive effort decreases suddenly, the electric motor coach has slip phenomena. This paper proposes a re-adhesion control based on disturbance observer and sensor-less vector control. The numerical simulation and experimental results point out that the proposed re-adhesion control system has the desired driving wheel torque response for the tested bogie system of electric coach. Based on this estimated adhesive effort, the re-adhesion control is performed to obtain the maximum transfer of the tractive effort.