• The Journal of Engineering Research
• /
• v.2 no.1
• /
• pp.165-174
• /
• 1997

It is not possible to define the earth's interior because of it complicity. However, it can be interpreted directly and/ or indirectly. Geophysics is the subject of this study. To study the possibility of construction supervision by geophysical method, geophysical prospecting was performed and studied at the SamYang pumping well area in Cheju Island, where, although underground dam was constructed, the saline water invade the pumping well area. This study focuses on the construction supervision by electrical measurements. Two electric resistivity survey lines are installed in the pumping well site, and at each line electric survey was conducted at ebb and flow tides. To increase the data quality SP (self-potential) survey was also performed. As a result the geophysical exploration methods explained the defect of construction well, and It shows that geophysical probe can be a useful tool for the construction supervision.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1686-1693
• /
• 2014

In this paper, oil-paper samples composed of transformer windings were used to investigate the insulation degradation process subjected to partial discharge (PD), with artificial defects inside to simulate the PD induced insulation degradation. To determine appropriate test voltages, the breakdown time obtained through a group of accelerated electrical degradation tests under high voltages was firstly fitted by two-parameter Weibull model to acquire the average breakdown time, which was then applied to establish the inverse power law life model to choose advisable test voltages. During the electrical degradation process, PD signals were synchronously detected by an ultra-high frequency (UHF) sensor from inception to breakdown. For PD analysis, the whole degradation process was divided into ten stages, and chaos theory was introduced to analyze the variation of three chaotic parameters with the development of electrical degradation, namely the largest Lyapunov exponent, correlation dimension and Komogorov entropy of PD amplitude time series. It is shown that deterministic chaos of PD is confirmed during the oil-paper degradation process, and the obtained results provide a new effective tool for the diagnosis of degradation of oil-paper insulation subjected to PD.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2509-2515
• /
• 2014

In this paper, the conventional vertical structure for VLSI circuits CMOS intend to improve the stress effects of active region and built-in threshold voltage. For these improvement, the proposed structure is shallow trench isolation of moat shape. We want to analysis the electron concentration distribution, gate bias vs energy band, thermal stress and dielectric enhanced field of thermal damage between vertical structure and proposed moat shape. Physically based models are the ambient and stress bias conditions of TCAD tool. As an analysis results, shallow trench structure were intended to be electric functions of passive as device dimensions shrink, the electrical characteristics influence of proposed STI structures on the transistor applications become stronger the potential difference electric field and saturation threshold voltage, are decreased the stress effects of active region. The fabricated device of based on analysis results data were the almost same characteristics of simulation results data.

• Land and Housing Review
• /
• v.4 no.3
• /
• pp.287-294
• /
• 2013

Energy saving strategy for public housing is given a sizable portion in Land and Housing corporation. From this reason, the consumer's characteristics and energy consciousness of public housing dweller was derived from field survey for compare with sale housing residents characteristics. Utilities fees (e.g. gas and electric) for public housing residents was about 50 percent of sales housing dweller, but real energy consumption was accounting for 70% of sales housing residents in electric consumption. Among the respondents for public housing dweller up to 80 percentile of end-user comment that they have less demanding utilities fees. Given the major energy saving strategies, such as install EMS, make a teaching tool for children, sale housing residents is more proactive approach to participant energy saving strategies than public housing residents.

• The Journal of Sustainable Design and Educational Environment Research
• /
• v.18 no.1
• /
• pp.38-48
• /
• 2019

The purpose of this study is to present a more effective daily checklist than the formal routine check before the experiment to prevent accidents in the university laboratory. To do this, we reconstructed the current daily checklist and previous research data and conducted a second Delphi survey. As a result, there were four general safeties such as arranging the laboratory, three mechanical safeties such as abnormal condition of machine and tool tightening parts, three electric safeties such as prohibition of loading around the electric distribution panel, six chemical safeties such as handling and managing harmful factors, three items of fire safety such as fire extinguisher inspection, five cases of gas safety gas container inspection, one item of biological safety such as the state of hand sterilizer management and one other item, which were provided in the daily checklist as twenty six categories in total. According to the opinions of related experts, it is necessary to have an easy and simplified daily checklist for actual daily checkups.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2021

In this paper, the cabinet shielding effectiveness (SE) including digital modules for nuclear power plants is analyzed depending on the internal structure and electromagnetic (EM) wave incidence angle. To analyze the SE, the cabinet and modules are modeled using the FEKO EM simulation tool. The SE is then obtained by comparing the electric field with and without the cabinet. In addition, the cabinet SE is observed by changing various conditions such as the spacing of each digital module, incidence angle, and the polarization of the EM wave at the 2.4 G[Hz frequency. To verify the results, the dipole antenna for SE measurements is fabricated, and the SE is measured in a semi-anechoic chamber. The result demonstrates that the SE by the cabinet structure can be expected to be higher when the polarization of the incident EM wave is horizontal to the ground and the distance between the digital modules is wide.

• Journal of Practical Engineering Education
• /
• v.12 no.2
• /
• pp.309-319
• /
• 2020

Billiards is a fun and popular sport, but both route planning and cueing prevent beginners from becoming skillful. A beginner in billiards requires constant concentration and training to reach the right level, but without the right motivating factor, it is easy to lose interests. This study aims to induce interest in billiards and accelerate learning by utilizing billiard path prediction and visualization on a highly immersive augmented reality platform that combines a stereo camera and a VR headset. For implementation, the placement of billiard balls is recognized through the OpenCV image processing program, and physics simulation, path search, and visualization are performed in Unity Engine. As a result, accurate path prediction can be achieved. This made it possible for beginners to reduce the psychological burden of planning the path, focus only on accurate cueing, and gradually increase their billiard proficiency by getting used to the path suggested by the algorithm for a long time. We confirm that the proposed AR billiards is remarkably effective as a learning assistant tool.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.3
• /
• pp.655-663
• /
• 2024

In order to meet the technological demand for indoor heating systems that ensure winter thermal comfort during the transition from internal combustion engines to electrification, a localized proximity heating module using surface heating elements was developed. The operational performance of heating module was tested in the low temperature chamber. The experiment conditions were varied by changing the chamber temperature (-10, 0℃), the air flow rate (6.2, 6.0, 4.2m³/h), the heater power (100, 80, 60, 40W). Thermal comfort model was confirmed using the CBE Thermal Comfort Tool applying ASHRAE standard 55. Under -10℃ condition, thermal comfort was satisfied at 23.4, 23.2℃ at power of 100W and air flow rate 6.0, 4.6m³/h. Under 0℃ condition, at power of 80W, air flow rate 6.2, 6.0m³/h, and at power of 60W, air flow rate 4.6m³/h showed results of 25.7, 26.1, 23.0℃, respectively, satisfying thermal comfort. This study analyzed the operating performance of the local proximity heating module in the low temperature chamber and applied thermal comfort model to prove applicability of local proximity heating module using surface heating elements and how to utilize the thermal comfort model.

• Journal of the Korean Electrochemical Society
• /
• v.23 no.2
• /
• pp.39-46
• /
• 2020

Composite electrodes for rechargeable batteries generally consist of active material, electric conductor, and polymeric binder. And their composition and distribution within the composite electrode determine the electrochemical activity in the electrochemical systems. However, it is not easy to quantify the physical properties of composite electrodes themselves using conventional experimental analysis tools. So, 3D structural modeling and simulation can be an efficient design tool by looking into the contact areas between particles and electric conductivity within the composite electrode. In this study, while maintaining the composition (LiCoO₂ : Super P Li^® : Polyvinylidene Fluoride (PVdF) = 93 : 3 : 4 by wt%) and loading level (13 mg cm^-2) of the composite electrode, the effects of LiCoO₂ size (10 ㎛ and 20 ㎛) and electrode density (2.8 g cm^-3, 3.0 g cm^-3, 3.2 g cm^-3, 3.5 g cm^-3, 4.0 g cm^-3) on the physical properties are investigated using a GeoDict software. With this tool, the composite electrode can be efficiently designed to optimize the contact area and electric conductivity.

• Archives of design research
• /
• v.19 no.5 s.67
• /
• pp.213-222
• /
• 2006

This paper presents MIDAS (Media Interaction Design Authoring System), an authoring toolkit for designers and artists to develop working prototypes in new interaction design projects. Field research were conducted to identify the requirements and a case study of designing new interactive products was carried out to examine the feasibility of the new tool. MIDAS provides easier ways of integrating hardware and software, to manage a wide range of electric input and output elements and to employ 3D Augmented Reality technology within conventional multimedia authoring tools, such as Director and Flash, which are popularly used by designers. MIDAS was used in case study projects of design education as well as by voluntary designers for evaluation. From the result of case studies, it was found that many design projects were successfully accomplished using MIDAS. Designers who participated in the projects reported that MIDAS not only helped them to concentrate more on ideation but also was very easy to use as they implemented the physical interface concepts without advanced engineering skills. It is expected that MIDAS can also support prototyping in interactive media an, tangible user interface development and related human computer interaction fields.