• 한국철도학회논문집
• /
• 제2권3호
• /
• pp.54-60
• /
• 1999

In this paper, design and construction process for the standardized electric motor car according to standard specification is described. Aluminum extrusion profiles and power and control system made domestically are used in the electric motor car. Also, plug-sliding door system for noise reduction and automatic train control system are developed and applied. Through the development of the electric motor car, most electric and control systems can be substituted by domestic standard systems, and safety and reliability of electric motor cars can be secured.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 추계학술대회 논문집
• /
• pp.151-153
• /
• 2007

Recently study on components for a electric golf car and a utility car driven by a electric motor has been performed actively, and the study on a drive motor, a inverter and a battery focuses on a small, light weight and high power density source to improve fuel efficiency using limited electric energy. Especially, since a utility car such as a golf car performance depends on initial acceleration and maximum speed capability, a drive system requires high power and large and wide operation area, This study therefore investigates on the interior permanent magnet synchronous motor with high power density and wide operation, and is verified with the test result after design and characteristic analysis is performed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1025-1026
• /
• 2007

Recently study on components for a electric golf car and a utility car driven by a electric motor has been performed actively, and the study on a drive motor, a inverter and a battery focuses on a small, light weight and high power density source to improve fuel efficiency using limited electric energy. Especially, since a utility car such as a golf car performance depends on initial acceleration and maximum speed capability, a drive system requires high power and large and wide operation area, This study therefore investigates on the interior permanent magnet synchronous motor with high power density and wide operation, and is verified with the test result after design and characteristic analysis is performed

• 예술인문사회 융합 멀티미디어 논문지
• /
• 제9권5호
• /
• pp.865-872
• /
• 2019

본 논문은 한국교통대학교 태양광 자작 자동차 동아리 늘해랑에서 WSC(World Solar Challenge)에 참가하기 위해 제작한 Solar Car 구동시스템에 대하여 서술한다. WSC는 세계 최대의 태양광 자동차 경주 대회로 별도의 자동차 규정을 가지고 있어 태양전지 면적이나 배터리 용량등에 제약을 두기 때문에, 제한된 규정내에서 최대 에너지 효율을 가지도록 구동시스템을 설계하는 것이 가장 중요한 기술적인 팩터이다. Solar car의 구동시스템은 태양광 에너지를 전기 에너지로 변환해주기 위한 solar array, 변환된 전기에너지를 최대 출력으로 추적하기 위한 MPPT(Maximum Power Point Tracker) controller, 생산된 전기에너지를 저장하기 위한 battery, 전기에너지를 역학에너지로 변환하여 차량 구동을 위한 BLDC(Brushless DC) motor, BLDC motor를 제어하기 위한 motor controller 등으로 구성되어 있다. 본 연구에서는 최적 구동 시스템을 위해 태양전지 에너지 변환 시스템과 배터리, 모터로 구성된 전기 구동시스템 설계에 대한 내용을 포함하고 있다.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.120-127
• /
• 2013

Hybrid electric vehicles have applied electric parts for saving fuel consumption and reducing levels of environmental pollution. Electrification of automobiles is indispensable for entering into global market because of enhanced environment restriction. ISG (Integrated Starter & Generator) system is one of main electric parts and can improve fuel efficiency more than other components by using Idle Stop & Go function and regenerative braking system. However, if ISG motor and inverter work under the continuously high load condition, it will make them the decrease of performance and durability. So the ISG motor and inverter need to properly design the cooling system of them. In this study, we suggested the enhancement points by modifying the thermal design of ISG motor and then confirmed the improvement of the cooling performance.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.29-34
• /
• 2014

Cooling the in-wheel motor in electric vehicles is critical to its performance and durability. In this study, thermal flow analysis was conducted by evaluating the thermal performance of two conventional cooling models for in-wheel motors under the continuous rating base speed condition. For conventional model #1, in which cooling oil was stagnant in the lower end of the motor, the maximum temperature of the coil was $221.7^{\circ}C$; for conventional model #2, in which cooling oil was circulated through the exit and entrance of the housing and jig, the maximum temperature of the coil was $155.4^{\circ}C$. Therefore, both models proved unsuitable for in-wheel motors since the motor control specifications limited the maximum temperature to $150^{\circ}C$.

• 한국자동차공학회논문집
• /
• 제20권1호
• /
• pp.61-67
• /
• 2012

The in-wheel motor used in green car was designed and constructed for an electric direct-drive traction system. It is difficult to connect cooling water piping because the in-wheel motor is located within the wheel structure. In the air cooling structure for the in-wheel motor, a outer surface on the housing is provided with cooling grooves to increase the heat transfer area. In this study, we carried out the analysis on the fluid flow and thermal characteristics of the in-wheel motor under the effects of motor speed and heat generation. In order to check the problem of heat release, the analysis has been performed using conjugate heat transfer (conduction and convection). As a result, flow fields and temperature distribution inside the in-wheel motor were obtained for base speed condition (1250 rpm) and maximum speed condition (5000 rpm). Also, the thermo-flow characteristics analysis of in-wheel motor for vehicles was performed in consideration of ram air effect. Therefore, we checked the feasibility of the air cooling for the housing geometry having cooling grooves and investigated the cooling performance enhancement.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.137-143
• /
• 1998

Numerical simulation is conducted to clarify the heat transfer and fluid flow characteristics of traction motor for electric car SIMPLE algorithm based on finite volume method is used to make linear algebra equation. The governing equations are solved by TDMA(TriDiagonal Matrix Algorithm) with line-by-line method and block correction. From the results of simulation, the characteristics of cooling pattern is strongly affected by the size of hole in stator core. In the case of high rotational speed of rotor, temperature difference along the axial direction is more decreased than that of low rotational speed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 추계학술대회 논문집
• /
• pp.247-252
• /
• 2001

In this study, an aluminum electric motor car with a modular front end made of composite materials is numerically evaluated applying the standard specifications for the urban EMU(Electric Multiple Unit) train. Structural analyses under compressive load, torsional load and free vibration satisfy the standard specifications, but analysis under normal load doesn't. By the way, the aluminum bodyshell of the car except the modular front end is almost same to that of the Korean standard EMU, which satisfy the standard specifications. It is presumed that the stiffness of the modular front end made of composite materials haves some influence on the strength of the aluminum bodyshell.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.109-112
• /
• 2001

In this paper, the development of the prototype electric vehicle for golf car is described. A brushless dc (BLDC) motor is applied as a prime mover. The BLDC motor is coupled directly to the reduction and differential gear system. The output power of the motor is decided to 2.2Kw at 3000 rpm, which is a general value of the golf car on the market today. The motor is driven by the microprocessor-based 3-phase PWM inverter system. We introduce the performance and functions of the BLDC motor and it's control system.