• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.8
• /
• pp.34-45
• /
• 1994

We studied threshold voltages and I-V characteristics. considering short channel effect of the fully depleted thin film n-channel SOI MOSFET. We presented a charge sharing model when the back surface of short channel shows accumulation depletion and inversion state respectively. A degree of charge sharing can be compared according to each of back-surface conditions. Mobility is not assumed as constant and besides bulk mobility both the mobility defined by acoustic phonon scattering and the mobility by surface roughness scattering are taken into consideration. I-V characteristics is then implemented by the mobility including vertical and parallel electric field. kThe validity of the model is proved with the 2-dimensional device simulation (MEDICI) and experimental results. The threshold voltage and charge sharing region controlled by source or drain reduced with increasing back gate voltage. The mobility is dependent upon scattering effect and electric field. so it has a strong influence on I-V characteristics.

• Journal of Magnetics
• /
• v.10 no.4
• /
• pp.149-151
• /
• 2005

The electric properties of a single crystal bismuth telluride doped with a small concentration of Erbium, $Bi_{z-x}Er_xTe_3$ with x = 0.002, are investigated as a function of temperature. The resistivity was obtained by using the van der Pauw method. The measured electrical resistivity is 78 ${\mu}{\Omega}cm$ at 4.2 K. The charge density of $Bi_{z-x}Er_xTe_3$ is found to be $2{\times}10^{19}/cm^3$ at 4.2 K. It turns out that $Bi_{z-x}Er_xTe_3$ is a p-type semiconductor. It is discussed that the high mobility and less density support that $Bi_{z-x}Er_xTe_3$ is a potential sensor with high energy resolution. Comparison with an established material (i.e. Au:Er alloy) is also discussed.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.3
• /
• pp.629-638
• /
• 2016

This paper proposes a State-of-Charge (SOC) balancing control of Battery Power Modules (BPMs) for a modularized battery for Electric Vehicles (EVs) without additional balancing circuits. The BPMs are substituted with the single converter in EVs located between the battery and the inverter. The BPM is composed of a two-phase interleaved boost converter with battery modules. The discharge current of each battery module can be controlled individually by using the BPM to achieve a balanced state as well as increased utilization of the battery capacity. Also, an SOC balancing method is proposed to reduce the equalization time, which satisfies the regulation of a constant DC-link voltage and a demand of the output power. The proposed system and the SOC balancing method are verified through simulation and experiment.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.3
• /
• pp.81-85
• /
• 2003

This paper describes the results of experiments made to examine the behavior of water droplet on the polymer surface and influence of the charge. In this experiment, water droplet was put on the polymer surface in an applied AC electric field and the investigations of its behavior were done with a high-speed video camera. It can be observed that the droplet elongates and vibrates with being pulled towards the positive electrode in a wave synchronism with the frequency of the power source. The volume and conductivity of water droplet are shown to have a marked effect on the mode of discharge development. These behaviors may be caused by the change of electric field of applied AC voltage and induced charges in/on the water droplet.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.4
• /
• pp.324-331
• /
• 2007

This paper studies new estimation method for state of charge (SOC) of the hybrid electric vehicle lithium battery using sliding mode observer. A simple R-C Lithium battery modeling technique is established and the errors caused by simple modeling was compensated by the sliding mode observer. The structure of the sliding mode observer is simple, but it shows robust control property against modeling errors and uncertainties. The performance of the system has been verified by the UUDS test. The test results of the proposed observer system shows robust tracking performance under real driving environments.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.11a
• /
• pp.69-69
• /
• 1996

• Nuclear Engineering and Technology
• /
• v.29 no.6
• /
• pp.451-458
• /
• 1997

Signal shapes from a closed-ended coaxial HPGe detector are investigated by numerical methods. The detector used in this study has a volume of 72 ㎤ with relative efficiency of 15%. The electric field and potential distributions in the detector are determined by solving the Poisson equation at the depletion and operating bias. Hence the time dependent signal shapes induced on the electrode are obtained from the energy balance consideration and tv solving the equation of motion for the charge carriers. For various initial positions of a charge carrier pair, the collection times of induced charge vary in the range of 70 - 404 nsec.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.89-91
• /
• 1995

This paper deals with calculation of surface charge density on current carrying conductors by FEM. The proposed algorithm is formulated by equation of continutity in conductor region and maxwell's equations outside, respectively, Surface charge density is calculated by electric scalar potential and boundary condition for electrostatic fields.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.5
• /
• pp.224-229
• /
• 2006

Many studies have been done on the application of residual charge measurement in cable degradation diagnosis. In this paper, the behavior of residual charges measured with water-tree degraded XLPE sheets and cable are discussed. At charge injection process, the charge is injected by applying dc voltage as a conventional method, suddenly cut-off ac voltage or impulse voltage. Therefore the residual charge is influenced by the applying process. At charge release process, transient dc current flows when applying ac high voltage and also ac high voltage superimposed to dc low voltage. From the results, new diagnosis method is suggested.

• Journal of the Korean Ceramic Society
• /
• v.36 no.9
• /
• pp.923-929
• /
• 1999

The cause of optical nonlinearity induced in thermally poled silica glass is believed to be the space charge polarization. Since the second order optical nonlinearity (electro-optic effect) can be used in optical switches the optical nonlinearity in silica glass has drawn a large attention. Space charge polarization occurs when an ionic conducting material is subjected to dc electric field by the blocking electrode. Thermal poling performed to induce the optical nonlinearity in silica glass is basically identical to the process generating space charge polarization. As a first step to understand the mechanism of space charge polarization in silica glass hence the induced optical nonlinearity the absorption currents as functions of time were measured for various types of silica glasses and analyzed by the theory of space charge polarization. It was found that the electrical relaxation exhibited a step by the space charge polarization in the relatively long time range and dielectric loss peak showed a maximum at a specific temperature which is depending on type of silica glass. It was turned out that this relaxation might be a cause of nonlinearity in electrical conductivity of silica glass.