• Structural Engineering and Mechanics
• /
• 제24권5호
• /
• pp.621-639
• /
• 2006

Stability of a cylindrical shell subject to a uniform axial compression, which is a power function of time, is examined within the framework of small strain elasto-plasticity. The material of the shell is incompressible and the effect of the elastic unloading is considered. Initially, employing the infinitesimal elastic-plastic deformation theory, the fundamental relations and Donnell type stability equations for a cylindrical shell have been obtained. Then, employing Galerkin's method, those equations have been reduced to a time dependent differential equation with variable coefficient. Finally, for two initial conditions applying a Ritz type variational method, the critical static and dynamic axial loads, the corresponding wave numbers and dynamic factor have been found. Using those results, the effects of the variations of loading parameters and the variations of power of time in the axial load expression as well as the variations of the radius to thickness ratio on the critical parameters of the shells for two initial conditions are also elucidated. Comparing results with those in the literature validates the present analysis.

• Structural Engineering and Mechanics
• /
• 제55권5호
• /
• pp.913-929
• /
• 2015

The ratcheting and strain cyclic behaviour of joined conical-cylindrical shells under uniaxial strain controlled, uniaxial and multiaxial stress controlled cyclic loading are investigated in the paper. The elasto-plastic deformation of the structure is simulated using Chaboche non-linear kinematic hardening model in finite element package ANSYS 13.0. The stress-strain response near the joint of conical and cylindrical shell portions is discussed in detail. The effects of strain amplitude, mean stress, stress amplitude and temperature on ratcheting are investigated. Under strain symmetric cycling, the stress amplitude increases with the increase in imposed strain amplitude. Under imposed uniaxial/multiaxial stress cycling, ratcheting strain increases with the increasing mean/amplitude values of stress and temperature. The abrupt change in geometry at the joint results in local plastic deformation inducing large strain variations in the vicinity of the joint. The forcing frequency corresponding to peak axial ratcheting strain amplitude is significantly smaller than the frequency of first linear elastic axial vibration mode. The strains predicted from quasi static analysis are significantly smaller as compared to the peak strains from dynamic analysis.

• Structural Engineering and Mechanics
• /
• 제9권2호
• /
• pp.111-126
• /
• 2000

Truss type structures are attractive to a variety of engineering applications on earth as well as in space due to their high stiffness to mass ratios and ease of construction and fabrication. During the service life, an individual member of a truss structure may lose load carrying capacity due to many reasons, which may lead to collapse of the structure. An analytical and computational procedure has been developed to study the response of truss structures subject to member failure under static and dynamic loadings. Emphasis is given to the dynamic effects of member failure and the propagation of local damage to other parts of the structure. The methodology developed is based on nonlinear finite element analysis technique and considers elasto-plastic material nonlinearity, postbuckling of members, and large deformation geometric nonlinearity. The pseudo force approach is used to represent the member failure. Results obtained for a planar nine-bay indeterminate truss undergoing sequential member failure show that failure of one member can initiate failure of several members in the structure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1569-1572
• /
• 2003

Meshfree approximations exhibit significant potential to solve partial differential equations. Meshfree methods have been successfully applied to various problems which the traditional finite element methods have difficulties to handle, including the quasi-static and dynamic fracture. large deformation problems, contact problems, and strain localization problems. A meshfree method based on the reproducing kernel particle approximation(RKPM) is applied to sheet metal forming analysis in this research. Metal forming examples, such as stretch forming and flanging operation, are analyzed to demonstrate the performance of the proposed meshfree method for largely deformed elasto-plastic material.

• Structural Engineering and Mechanics
• /
• 제91권4호
• /
• pp.369-382
• /
• 2024

The earthquake loss assessment framework of ductile reinforced concrete (or RC) frame using component-performance -based methodology was studied in this paper. The elasto-plastic rotation angle was used as the damage indicator of structural component, and the damage-to-loss model was proposed on the basis of the deformation indicator of structural component. Dynamic instability during incremental dynamic analysis was taken as collapse criterion, and column failure was taken as criterion that structure has to be demolished. Expected earthquake losses of low-rise, mid-rise and high-rise RC frames were discussed. The expected earthquake loss encompassed collapse loss, demolition loss and repair loss. Furthermore, component groups of RC frame were divided into structural components, nonstructural components and rugged components. The results indicate that ductile RC frame is more likely to be demolished than collapse, especially in low-rise and mid-rise RC frames. Furthermore, the less collapse margin ratio the structure has, the more demolition probability the structure will suffer under rare earthquake. The demolition share of total earthquake loss might be more prominent than repair share and collapse share in ductile RC frame.

• 한국강구조학회 논문집
• /
• 제23권5호
• /
• pp.535-546
• /
• 2011

본 연구에서는 다양한 명시적 호장법을 사용하여 공간프레임의 반강접 탄소성 후좌굴 해석을 수행하였다. 이를 위해 이전 연구를 발전시켜 다양한 명시적 알고리즘의 호장법과 명시적, 묵시적 해석법에 동시에 적용 가능한 반강접 탄소성 공간프레임요소를 제안하였다. 다양한 명시적 호장법은 예측단계와 수렴단계에 명시적 해석법인 동적이완법을 적용한 것을 의미한다. 따라서 명시적 호장법에는 명시적(예측단계)-명시적(예측단계) 호장법, 명시적(예측단계)-묵시적(수렴단계) 호장법, 묵시적(예측단계)-명시적(수렴단계) 호장법으로 구분된다. 또한 명시적 호장법에 적용 가능하도록 수정된 반강접 탄소성 공간프레임요소는 오일러리안 유한변형이론에 의해 강체회전변형을 고려하였기 때문에 대변위가 발생하는 기하학적 비선형 문제에 적용될 수 있고, 완전 탄소성 소성힌지 알고리즘에 의한 재료적 비선형성을 고려하였으며, 부재내부에 정적 응축된 회전 및 축방향 성분의 선형 스프링에 의해 접합부 반강접 특성을 반영하였다. 제안된 해석법을 이용하여 검증예제를 수행함으로써 본 연구에서 제안된 다양한 명시적 호장법 및 공간프레임요소의 정확성을 검증한다.

• 한국농공학회논문집
• /
• 제46권4호
• /
• pp.75-84
• /
• 2004

The evaluation technique of seismic performance on agricultural infrastructure based on dynamic numerical simulations, which Included a cyclic elasto-plastic and a viscoelastic-viscoplastic constitutive model to actual multi-layered ground conditions during large earthquake were performed by a liquefaction analysis in the present study. From the liquefaction analysis, it was verified that the models can give a good description of the damping characteristics and liquefaction phenomena of ground accurately during large event which induces plastic deformation in large strain range.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1995년도 가을 학술발표회 논문집
• /
• pp.234-241
• /
• 1995

Offshore structures are exposed to higher probability of collision with ship because of their limited mobility. In general, the consequence of the collision is reported to be relatively small and it is desirable to consider minor collisions in the design stage. It is important to have a comprehensive understanding of the dynamic responses of a tubular, their main member, under collision to design offshore structure against possible accidents. It is needed to estimate the probable extent of damage of a tubular, depth of dent, affected by the time history of impact load in ender to design a tubular strong enough for collision. In this paper, dynamic behaviors of a tubular due to the lateral impact are investigated through the numerical simulations with hydrocode DYNA3D, a three dimensional elasto-plastic large deformation impact contact problem analyzing program.

• 대한기계학회논문집
• /
• 제16권5호
• /
• pp.910-923
• /
• 1992

본 연구에서는 가장 응용 빈도가 큰 크랭크-레버 4절 기구를 제작하고 강성과 유연성 두가지 베어링을 사용하여 연결봉과 레버의 중점의 변형률을 스트레인 게이지 로 측정하여 앞의 이론 논문에서 수행한 수치해석의 결과와 비교 검토하였다.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.