• Advances in concrete construction
• /
• 제14권2호
• /
• pp.93-102
• /
• 2022

In this study, limestone powder (LS) and fly ash (FA) were used as powder materials in self-compacting concrete (SCC) in increasing quantities in addition to cement, so that the two powders commonly used in the production of SCC could be compared in the same study. Considering the reduction of the maximum aggregate size in SCC, 10 mm or 16 mm was selected as the coarse aggregate size. The properties of fresh concrete were determined by slump flow (including T₅₀₀ time), V-funnel and J-ring experiments. The experimental results showed that as the amount of both LS and FA increased, the slump flow also increased. The increase in powder material had a negative effect on V-funnel flow times, causing it to increase; however, the increase in FA concretes was smaller compared to LS ones. The increase in the powder content reduced the amount of blockage in the J-ring test for both aggregate sizes. As the hardened concrete properties, the compressive and splitting strengths as well as the modulus of elasticity were determined. Longitudinal and transverse deformations were measured by attaching a special frame to the cylindrical specimens and the values of Poisson's ratio, initiation and critical stresses were obtained. Despite having a similar W/C ratio, all SCC exhibited higher compressive strength than NVC. Compressive strength increased with increasing powder content for both LS and FA; however, the increase of the FA was higher than the LS due to the pozzolanic effect. SCC with a coarse aggregate size of 16 mm showed higher strength than 10 mm for both powders. Similarly, the modulus of elasticity increased with the amount of powder material. Inelastic properties, which are rarely found in the literature for SCC, were determined by measuring the initial and critical stresses. Crack formation in SCC begins under lower stresses (corresponding to lower initial stresses) than in normal concretes, while critical stresses indicate a more brittle behavior by taking higher values.

• Steel and Composite Structures
• /
• 제44권3호
• /
• pp.309-324
• /
• 2022

The post-fire elastic stiffness and performance of concrete-filled steel tube (CFST) columns containing recycled aggregate concrete (RAC) has rarely been addressed, particularly in terms of material properties. This study was conducted with the aim of assessing the modulus of elasticity of recycled aggregate concrete-filled steel tube (RACFST) stub columns following thermal loading. The test data were employed to model and assess the elastic modulus of circular RACFST stub columns subjected to axial loading after exposure to elevated temperatures. The length/diameter ratio of the specimens was less than three to prevent the sensitivity of overall buckling for the stub columns. The gene expression programming (GEP) method was employed for the model development. The GEP model was derived based on a comprehensive experimental database of heated and non-heated RACFST stub columns that have been properly gathered from the open literature. In this study, by using specifications of 149 specimens, the variables were the steel section ratio, applied temperature, yielding strength of steel, compressive strength of plain concrete, and elastic modulus of steel tube and concrete core (RAC). Moreover, parametric and sensitivity analyses were also performed to determine the contribution of different effective parameters to the post-fire elastic modulus. Additionally, comparisons and verification of the effectiveness of the proposed model were made between the values obtained from the GEP model and the formulas proposed by different researchers. Through the analyses and comparisons of the developed model against formulas available in the literature, the acceptable accuracy of the model for predicting the post-fire modulus of elasticity of circular RACFST stub columns was seen.

• Structural Engineering and Mechanics
• /
• 제85권1호
• /
• pp.29-53
• /
• 2023

High-strength shielding concrete against gamma radiation is a priority for many medical and industrial facilities. This paper aimed to investigate the gamma-ray shielding properties of high-strength hematite concrete mixed with silica fume (SF) with nanoparticles of lead dioxide (PbO₂), tungsten oxide (WO₃), and bismuth oxide (Bi₂O₃). The effect of mixing steel fibres with the aforementioned binders was also investigated. The reference mixture was prepared for high-strength concrete (HSCC) containing 100% hematite coarse and fine aggregate. Thirteen mixtures containing 5% SF and nanoparticles of PbO₂, WO₃, and Bi₂O₃ (2%, 5%, and 7% of the cement mass, respectively) were prepared. Steel fibres were added at a volume ratio of 0.28% of the volume of concrete with 5% of nanoparticles. The slump test was conducted to workability of fresh concrete Unit weight water permeability, compressive strength, splitting tensile strength, flexural strength, and modulus of elasticity tests were conducted to assess concrete's engineering properties at 28 days. Gamma-ray radiation of 137Cs emits photons with an energy of 662 keV, and that of 60Co emits two photons with energies of 1173 and 1332 keV were applied on concrete specimens to assess radiation shielding properties. Nanoparticles partially replacing cement reduced slump in workability of fresh concrete. The compressive strength of mixtures, including nanoparticles was shown to be greater, achieving 94.5 MPa for the mixture consisting of 7.5 PbO2. In contrast, the mixture (5PbO₂-F) containing steel fibres achieved the highest values for splitting tensile, flexural strength, and modulus of elasticity (11.71, 15.97, and 42,840 MPa, respectively). High-strength shielded concrete (7.5PbO2) showed the best radiation protection. It also showed the minimum concrete thickness required to prevent the transmission of radiation.

• 농업과학연구
• /
• 제48권4호
• /
• pp.815-829
• /
• 2021

The purpose of this study is to construct a flatfish outlook model that is consistent with the "Fisheries outlook" monthly publication of the fisheries outlook center of the Korea Maritime Institute (KMI). In particular, it was designed as a partial equilibrium model limited to flatfish items, but a model was constructed with a dynamic ecological equation model (DEEM) system, considering biological breeding and shipping times. Due to limited amounts of monthly data, the market equilibrium price was calculated using a recursive model method as the inverse demand. The main research results and implications are as follows. As a result of estimating young fish inventory levels, the coefficient of the young fish inventory in the previous period was estimated to be 0.03, which was not statistically significant. Because there is distinct seasonality, when estimating the breeding outcomes, the elasticity of breeding in the previous period was found to exceed 0.7, and it increased more as the weight of the fish increased, in addition, the shipment coefficient gradually increased as the weight increased, which means that as the fish weight increased, the shipment compared to the breeding volume increased. When estimating shipments, the elasticity of breeding in previous period was estimated to respond elastically as the weight increases. The price flexibility coefficient of the total supply was inelastically estimated to be -0.19. Finally, according to a model predictive power test, the Theil U1 was estimated to be very low for all of the predictors, indicating excellent predictive power.

• Journal of the Korean Wood Science and Technology
• /
• 제51권4호
• /
• pp.239-252
• /
• 2023

In this study, bending and compression strength tests were performed to investigate effect of composition of layer layout of Larix cross-laminated timber (CLT) on mechanical properties. The Larix CLT consists of five laminae, and specimens were classified into four types according to grade and composition of layer. The layer's layout were composited as follows 1) cross-laminating layers in major and minor direction (Type A), and 2) cross-laminating external layer in major direction and internal layer applied grade of layer in minor direction (Type B). E12 and E16 were used as grades of lamina for major direction layer of Type A and external layer of Type B according to KS F 3020. In results of the bending test of CLT using same grade layer according to layer composition, the modulus of elasticity (MOE) of Type B was higher than Type A. In case of prediction of bending MOE of Larix CLT, the experimental MOE was higher than 1.00 to 1.09 times for Shear analogy method and 1.14 to 1.25 times for Gamma method. Therefore, it is recommended to predict the bending MOE for Larix CLT by shear analogy method. Compression strength of CLT in accordance with layer composition was measured to be 2% and 9% higher for Type A using E12 and E16 layers than Type B, respectively. In failure mode of Type A, progress direction of failure generated under compression load was confirmed to transfer from major layer to minor layer by rolling shear or bonding line failure due to the middle lamina in major direction.

• Tribology and Lubricants
• /
• 제39권6호
• /
• pp.235-243
• /
• 2023

This paper presents the fabrication process of water-lubricated plastic bearings. Plastic bearings require good mechanical properties and tribological properties as well as elasticity and shock resistance, especially when lubricated in dirty water conditions. In this study, sleeve-type plastic bearings are produced by winding a prepreg sheet, which primary contains nitrile rubber (NBR)-modified epoxy, self-lubricating fillers, and various types of lattice-structured reinforcing fibers such as carbon, Aramid, and polyethylene terephthalate. A thermosetting epoxy is chemically modified with NBR to impart elasticity and low-friction characteristics in water conditions. Experimental investigations are conducted to examine the mechanical and tribological characteristics of the developed bearing materials, and the results are compared with the characteristics of a commercial plastic bearing (Thordon SXL), well known as a water-lubricated bearing. A Thordon bearing (mainly composed of polyurethane) exhibits an extremely low load-bearing capacity and is thus only suitable for medium loading (1~10MPa). The tribological characteristics of the test materials are evaluated through Falex block-on-ring (LFW-1) friction and wear tests. The results indicate that friction exhibited by the carbon-fiber-reinforced NBR-10wt.%-modified epoxy composite material, incorporated with the addition of 20wt.% UHMWPE and 6wt.% paraffin wax, is lower than that of the Thorden bearings, whereas its wear resistance surpass that of Thorden ones. Because of these features, the load carrying capacity of the fabricated composite (>10MPa) is higher than that of the Thorden bearings. These results confirm the applicability of water-lubricated plastic bearing materials developed in this study.

• The Journal of Advanced Prosthodontics
• /
• 제10권1호
• /
• pp.25-31
• /
• 2018

PURPOSE. The aim of the present study was to record the metal-ceramic bond strength of a feldspathic dental porcelain and a Co-Cr alloy, using the Direct Metal Laser Sintering technique (DMLS) for the fabrication of metal substrates. MATERIALS AND METHODS. Ten metal substrates were fabricated with powder of a dental Co-Cr alloy using DMLS technique (test group) in dimensions according to ISO 9693. Another ten substrates were fabricated with a casing dental Co-Cr alloy using classic casting technique (control group) for comparison. Another three substrates were fabricated using each technique to record the Modulus of Elasticity (E) of the used alloys. All substrates were examined to record external and internal porosity. Feldspathic porcelain was applied on the substrates. Specimens were tested using the three-point bending test. The failure mode was determined using optical and scanning electron microscopy. The statistical analysis was performed using t-test. RESULTS. Substrates prepared using DMLS technique did not show internal porosity as compared to those produced using the casting technique. The E of control and test group was $222{\pm}5.13GPa$ and $227{\pm}3GPa$, respectively. The bond strength was $51.87{\pm}7.50MPa$ for test group and $54.60{\pm}6.20MPa$ for control group. No statistically significant differences between the two groups were recorded. The mode of failure was mainly cohesive for all specimens. CONCLUSION. Specimens produced by the DMLS technique cover the lowest acceptable metal-ceramic bond strength of 25 MPa specified in ISO 9693 and present satisfactory bond strength for clinical use.

• 한국해양공학회지
• /
• 제26권6호
• /
• pp.19-26
• /
• 2012

Recently the world has been suffering from difficulties related to the demand and supply of energy due to the democratic movements sweeping across the Middle East. Consequently, many have turned their attention to never-developed extreme regions such as the polar lands or deep sea, which contain many underground resources. This research investigated the strength and initial elastic modulus values of eternally frozen ground through a uniaxial compression test and indirect tensile test using frozen artificial soil specimens. To ensure accurate test results, a sandymud mixture of standard Jumunjin sand and kaolinite (20% in weight) was used for the specimens in these laboratory tests. Specimen were prepared by varying the water content ratio (7%, 15%, and 20%). Then, the variation in the strength value, depending on the water content, was observed. This research also established three kinds of environments under freezing temperatures of $-5^{\circ}C$, $-10^{\circ}C$, and $-15^{\circ}C$. Then, the variation in the strength value was observed, depending on the freezing environment. In addition, the tests divided the loading rate into 6 phases and observed the variation in the stress-strain ratio, depending on the loading rate. The test data showed that a lower freezing temperature resulted in a larger strength value. An increase in the ice content in the specimen with the increase in the water content ratio influenced the strength value of the specimen. A faster load rate had a greater influence on the uniaxial compression and indirect tensile strengths of a frozen specimen and produced a different strength engineering property through the initial tangential modulus of elasticity. Finally, the long-term strength under a constant water content ratio and freezing temperature was checked by producing stress-strain ratio curves depending on the loading rate.

• 콘크리트학회논문집
• /
• 제25권4호
• /
• pp.439-446
• /
• 2013

이 연구의 목적은 국내생산이 가능한 자철석을 이용한 중량 콘크리트의 유동성 및 역학적 특성을 평가하고 설계기준의 안전성을 확인하는 것이다. 주요변수로는 물-시멘트 비와 보통중량 굵은골재(화강석)의 치환율이다. 배합된 콘크리트 기건 단위용적질량은 $2446{\sim}3426kg/m^3$ 범위에 있었다. 측정된 역학적 특성들은 압축강도, 응력-변형률관계, 탄성계수, 쪼갬인장강도, 파괴계수 그리고 철근과의 부착응력-미끄러짐 관계 등이다. 실험 결과, 자철석 중량 콘크리트의 초기 슬럼프는 보통중량 굵은골재 치환율이 증가할수록 향상하였다. 압축강도, 인장저항성 등의 역학적 특성은 굵은골재 치환율에 따른 영향이 미미하였으나, 응력-변형률 관계와 탄성계수는 콘크리트 단위용적질량에 중요한 영향을 받았다. ACI 349-06 및 CEB-FIP 제안모델들은 일반적으로 자철석 중량 콘크리트의 역학적 특성들에 대해 안전측에 있지만, 탄성계수 및 쪼갬인장강도에 대해서는 콘크리트 단위용적질량을 고려하여 보완될 필요가 있었다.

• 대한화장품학회지
• /
• 제45권4호
• /
• pp.381-388
• /
• 2019

개인의 피부특성을 반영한 화장품에 대한 관심이 증가함에 따라 본 연구에서는 개인의 특성을 분류하기 위해 한의학 변증(辨證) 개념을 도입하여 피부특징 및 대상자 특성을 구분하고자 하였다. 변증 중 노화와 관련 있는 음허(陰虛)변증을 선정하였고, 건강한 40대와 50대 여성 218명을 음허변증으로 구분하여 피부특성과 설문응답패턴을 분석하였다. 피부특성은 Corneometer^®, Cutometer^®, Janus lll 측정기기를 활용하여 보습, 탄력, 모공, 주름, 색소침착, 피부색 및 피지 항목을 측정하였다. 설문은 음허설문지(yin-deficiency questionnaire, YDQ)와 피부상태설문지(modified skin type questionnaire)로 구성되어 있는데, 음허변증 여부에 따른 교차비(odds ratio) 분석과 유의한 피부특성 차이를 나타내는 설문 분석의 두 단계로 구분하여 분석하였다. 그 결과, 음허로 변증된 집단은 아닌 집단에 비해 보습과 탄력이 감소하고, 피부 붉기가 증가하는 유의한 차이를 확인하였으며, 얼굴 열감과 불면, 신체 수분 감소 항목에서 불편감을 호소하였고 피부 민감성 항목과 연관이 있음을 확인하였다. 본 연구 결과를 활용하여 음허변증과 관련된 설문 중 수분, 탄력, 붉기의 피부특성을 나타내는 설문을 바탕으로 해당 고객에게 제품을 추천할 수 있을 것으로 사료된다.