• 한국농공학회지
• /
• 제38권6호
• /
• pp.83-95
• /
• 1996

The normal cement concrete is widely used material to build the construction recently, but it has a fault to increase the dead load on account of its unit weight is large compared with strength. So, main purpose of this study was to establish the physical and mechanical properties of lightweight concrete using expanded polystyrene bead on fine aggregate and natural gravel, expanded clay and pumice stone on coarse aggregate. The test rusults of this study are summarized as follows; 1. The water-cement ratio of concrete using pumice stone was larger than that of the concrete using natural gravel and expanded clay. 2. The unit weights of concrete using pumice stone and expanded caly were shown less than 1,000g/$m^3$. 3. The compressive strengths of all types were shown less than 60kg/$cm^2$, tensile and bending strengths were shown less than l3kg/$cm^2$ and 3lkg/$cm^2$$^2$, respectively. 4. The pulse velocity of concrete was shown similar with using natural gravel and pumice stone, and shown the lowest using pumice stone. 5. The dynamic modulus of elasticity of concrete was shown considerably smaller, and shown the lowest using pumice stone. 6. The static modulus of elasticity of concrete using expanded clay and pumice stone were shown considerably smaller, and shown 22% ~29% as compared with the dynamic modulus of elasticity. 7. The stress-strain curves of concrete were shown similar, generally. And the curves were repeated at short intervals increase and decreased irregularly.

• 임산에너지
• /
• 제22권2호
• /
• pp.60-68
• /
• 2003

목재의 기계적 특성을 평가하기 위하여 여러 가지 비파괴 측정 기술이 도입되고 있다. 본 실험은 낙엽송(Larix kaempferi Carr.) 소경재 원목을 초음파의 통과 속도와 종진동의 고유진동수를 이용한 비파괴 측정 기술로 영계수를 측정하여 휨강도 실험을 통해 얻은 실측 영계수와 휨파괴계수의 상관관계를 검토하였다. 실험에는 50본의 소경재 원목이 사용되었다. 종진동의 고유진동수를 이용한 영계수와 실측 영계수는 비교적 높은 상관관계를 나타내었다. 초음파를 이용한 비파괴 영계수 측정은 옹이의 출현빈도가 높은 원목의 선별에 효과적이었으며 종진동의 고유진동수를 이용한 측정은 할렬의 출현빈도가 높은 원목의 선별에 효과적임을 확인하였다.

• 한국도로학회논문집
• /
• 제9권4호
• /
• pp.205-213
• /
• 2007

본 연구에서는 포장용 콘크리트의 강도실험을 통해 강도간의 상관관계식을 도출하는 것을 목적으로 하였다. 강도로서 재령별 압축강도, 휨강도, 할렬인장강도와 탄성계수를 측정하였다. 배합변수는 조골재(화강암, 석회암, 사암), 세골재(자연사, 세척사, 부순모래) 및 단위시멘트량(315-375kg)을 변수로 하였다. 전체적으로 골재나 단위시멘트량보다는 재령에 의해 전형적인 강도곡선을 따라 뚜렷하게 변화함을 보여준다. 이러한 강도결과를 바탕으로 휨강도와 압축강도, 할렬인장강도와 압축강도, 탄성계수와 압축강도, 할렬인장강도와 휨강도의 상관관계를 분석한 결과 휨강도와 압축강도, 탄성계수와 압축강도는 기존의 관례대로 제곱근(n=0.5)의 상관관계식이 잘 맞음을 알 수 있었다. 할렬인장강도와 휨강도는 선형의 상관관계식으로 표현하였고, 할렬인장강도와 압축강도는 n=0.87의 지수승을 사용한 경우가 가장 적합한 것으로 나타났다.

• 대한화장품학회지
• /
• 제36권1호
• /
• pp.65-69
• /
• 2010

콜라겐은 포유동물의 가장 풍부한 동물성 단백짙로, 전체 단백질의 약 30 %를 차지하며, 결합 조직에 존재하며 대부분의 장기의 구조적 지지에 기여한다. Tripeptide (glycine-proline-hydroxyproline: INCI name Tripeptide-29) 는 collagen type 1의 주성분이며, palmitoyl tripeptide (palmitoyl-glycine-proline-hydroxyproline: INCI name Palmitoyl Tripeptide-29) 는 콜라겐의 합성을 촉진하는 항노화 불질로서 디자인된 합성소재이다 합성된 웹타이드 유도체는 HPLC를 이용하여 분식하였다. in vitro test를 통하여 콜라겐합성과 섬유아세포 증식 효능을 확인하였고, 비침습적 기기를 사용하여 피검자에 대한 8주간의 적용결과 피부주름과 탄력의 상당한 개선을 확인하였다. Palmitoyl tripeptide는 우수한 항노화 효능을 갖는 화장품 소재로 사료된다.

• 한국건설순환자원학회논문집
• /
• 제6권4호
• /
• pp.319-323
• /
• 2018

페로니켈 슬래그는 페로니켈의 제련과정에서 발생하는 산업부산물로, 냉각 방법에 따라 서냉 페로니켈 슬래그와 수쇄 페로니켈 슬래그로 구분된다. 본 연구의 목적은 서냉 페로니켈 슬래그(air-cooled ferronickel slag, ACFNS) 잔골재를 이용한 콘크리트의 역학적 특성 및 동결융해 저항성을 평가하는 것이다. 이를 위하여 물-시멘트비 50%에 대해서 ACFNS 혼입률을 잔골재용적비로 7가지 수준(0%, 20%, 30%, 40%, 50%, 70%, 100%)으로 변화시켜 ACFNS 잔골재를 이용한 콘크리트를 제작하였다. 실험결과로부터, ACFNS 잔골재 콘크리트의 압축강도 및 정탄성계수는 ACFNS의 혼입률이 증가할수록 커지고, 동결융해 저항성은 동결융해 300 사이클 동안 상대동탄성계수가 90% 이상으로 나타난 기준 콘크리트와 유사한 것으로 나타났다.

• Structural Engineering and Mechanics
• /
• 제78권5호
• /
• pp.585-597
• /
• 2021

This paper presents a comparative study of analytical method, finite element method (FEM) and Multilayer Perceptron (MLP) for analysis of a contact problem. The problem consists of a functionally graded (FG) layer resting on a half plane and pressed with distributed load from the top. Firstly, analytical solution of the problem is obtained by using theory of elasticity and integral transform techniques. The problem is reduced a system of integral equation in which the contact pressure are unknown functions. The numerical solution of the integral equation was carried out with Gauss-Jacobi integration formulation. Secondly, finite element model of the problem is constituted using ANSYS software and the two-dimensional analysis of the problem is carried out. The results show that contact areas and the contact stresses obtained from FEM provide boundary conditions of the problem as well as analytical results. Thirdly, the contact problem has been extended based on the MLP. The MLP with three-layer was used to calculate the contact distances. Material properties and loading states were created by giving examples of different values were used at the training and test stages of MLP. Program code was rewritten in C++. As a result, average deviation values such as 0.375 and 1.465 was obtained for FEM and MLP respectively. The contact areas and contact stresses obtained from FEM and MLP are very close to results obtained from analytical method. Finally, this study provides evidence that there is a good agreement between three methods and the stiffness parameters has an important effect on the contact stresses and contact areas.

• 한국해양공학회지
• /
• 제36권4호
• /
• pp.217-231
• /
• 2022

Reinforced polyurethane foam (R-PUF), a material for liquefied natural gas cargo containment systems, is expected to have different mechanical properties depending on its stacking position of foaming as the glass fiber reinforcement of R-PUF sinks inside R-PUF under the influence of gravity. In addition, since R-PUF is not a homogeneous material, it is also expected that the coordinate direction within this material has a great correlation with the mechanical properties. So, this study was conducted to confirm this correlation with the one between the mechanical properties and the stacking position. In particular, in this study, R-PUF of 3 different densities (130, 170, and 210 kg/m³) was used, and tensile, compression, and shear tests of this material were performed under 5 temperatures. As a result of the tests, it was confirmed that the strength and modulus of elasticity of the material increased as the temperature decreased. Specifically, the strength and modulus of elasticity in the Z direction, which was the lamination direction, tended to be lower than those in the other directions. Finally, the strength and elastic modulus of different specimens of the material found at the bottom of their lamination compared to the specimens with these properties found at positions other than their lamination bottom were evaluated. Further analysis confirmed that as the temperature decreased, hardening of R-PUF occurred, indicating that the strength and modulus of elasticity increased. On the other hand, as the density of R-PUF increased, a sharp increase in strength and elastic modulus of R-PUF was observed.

• 한국지반공학회논문집
• /
• 제23권8호
• /
• pp.59-68
• /
• 2007

사질토의 직교 이방 탄성계수를 실험적 방법과 개별 요소법을 이용하여 측정하고 결과를 정량적으로 비교-분석하였다. 실내 시험에서는 미소 응력 제어 반복재하시험과 벤더 엘리먼트의 측정 결과를 조합하여 탄성 특성을 구하였으며, 개별 요소법에서는 실내 시험 방법과 상응하는 반복재하시험을 모사하였다. 축 방향 및 전단방향에 관련된 탄성 특성의 비교 결과는 제한된 조건에서도 개별 요소법이 복잡한 실내 시험 과정을 모사할 수 있음을 보여주었다. 방사 방향 재하시험 결과에서 나타난 두 방법 간 차이의 비교 분석 결과는 개별 요소법이 실내 시험으로 구한 개별 측정치의 정량적 타당성을 확인하는데 충분히 활용될 수 있음을 보여준다.

• Advances in concrete construction
• /
• 제13권 2호
• /
• pp.123-132
• /
• 2022

This paper aims to adapt Multilinear regression (MLR) to predict the strength and toughness of SIFCON containing various pozzolanic materials. Slurry Infiltrated Fibrous Concrete (SIFCON) is one of the most common terms used in concrete manufacturing, known for its benefits such as high ductility, toughness and high ultimate strength. Assessment of compressive strength (CS.), flexural strength (F.S.), splitting tensile strength (STS), dynamic elasticity modulus (DME) and impact energy (I.E.) using the experimental approach is too costly. It is time-consuming, and a slight error can lead to a repeat of the test and, to solve this, alternative methods are used to predict the strength and toughness properties of SIFCON. In the present study, the experimentally investigated SIFCON data about various mix proportions are used to predict the strength and toughness properties using regression analysis-multilinear regression (MLR) models. The input parameters used in regression models are cement, fibre, fly ash, Metakaolin, fine aggregate, blast furnace slag, bottom ash, water-cement ratio, and the strength and toughness properties of SIFCON at 28 days is the output parameter. The models are developed and validated using data obtained from the experimental investigation. The investigations were done on 36 SIFCON mixes, and specimens were cast and tested after 28 days of curing. The MLR model yields correlation between predicted and actual values of the compressive strength (C.S.), flexural strength, splitting tensile strength, dynamic modulus of elasticity and impact energy. R-squared values for the relationship between observed and predicted compressive strength are 0.9548, flexural strength 0.9058, split tensile strength 0.9047, dynamic modulus of elasticity 0.8611 for impact energy 0.8366. This examination shows that the MLR model can predict the strength and toughness properties of SIFCON.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 봄 학술발표회 논문집
• /
• pp.187-190
• /
• 1994

During the initial design phases for prestressed concrete structures, the mecessary information concerning the physical properties of the hardened concrete such as creep, drying shrinkage, modulus of elasticity, and Poisson's ratio are obtained from design assumptions or accepted standards. But these assumptions may not totally reflect the actual long-term behavior of the concrete. So they may be of limited use in predicting the actual behavior. The purpose of this paper is to describe the test procedures and methods of evaluation which were used during the long-term study.