• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 가을 학술발표회 논문집
• /
• pp.145-150
• /
• 1998

• 한국지반공학회논문집
• /
• 제31권3호
• /
• pp.63-72
• /
• 2015

본 연구는 노상토의 다짐특성 평가를 위해 특성이 다른 세 가지 강성측정 시험법으로 측정한 탄성계수의 상관관계 및 연관성에 대해 논의하였다. 미소변형률(${\approx}0.001%$) 범위의 흙강성측정기(SSG), 중변형률(${\approx}0.01{\sim}0.1%$) 범위의 정적 평판재하시험(PLT), 관입저항을 이용하는 동적콘관입시험기(DCP)가 탄성계수 측정에 이용되었다. 변형률 범위가 다른 시험방법에 의해 측정한 탄성계수를 실무에 적용하기 위해서는, 각각의 측정치에 대한 상관관계 및 연관성에 대해 사전에 파악되어야 한다. 국내 외 여러 조건의 노상토에 대해서 세 가지 방법을 이용하여 측정한 탄성계수($E_{SSG}$, $E_{PLT}$, $E_{DCP}$)를 비교 분석한 결과에 따르면, 흙의 종류 및 응력 조건에 따라 각 방법에 의해 측정된 탄성계수가 상이한 결과를 나타내었다. 전체 수집된 데이터 중 시멘트 처리토를 제외한 일반적인 노상토를 대상으로 한 상관성 분석결과, 정적 탄성계수($E_{PLT}$)는 동적 탄성계수($E_{SSG}$) 대비 60~80%의 크기를 나타나는 것으로 평가되었다. 시멘트 처리토와 같은 특이 토질은 정적 탄성계수($E_{PLT}$) 측정 시 구속압의 영향을 크게 받기 때문에, 다른 일반 토질과 상관관계 비교시 응력보정을 수행하여야 한다. 또한, 동적콘관입시험 결과를 이용하여 탄성계수($E_{DCP}$) 예측 시, 200MPa 이내의 범위에서 탄성계수 데이터가 좀더 신뢰도 높은 상관관계를 나타내었다.

• 대한기계학회논문집A
• /
• 제28권10호
• /
• pp.1603-1611
• /
• 2004

The validity of 'modified overlay model' to describe the cyclic behavior of annealed 316L stainless steel at room temperature was investigated. Material parameters(~f$_{i}$, m$_{i}$b, η, E) fur the model were obtained through constant strain amplitude test. The strain amplitude dependency of elastic limit and cyclic hardening, which were the characteristics of this model, were considered. Eight subelements were used to describe the nonlinearity of the hysteresis loops. The calculated hysteresis curve in each condition (0.5％, 0.7％, 0.9％ train amplitude test) was very close to the experimental one. Two tests, incremental step test and 5-step test, ere performed to check the validity of 'modified overlay model'. The elastic limit was saturated to the one of the highest strain amplitudes of the block in the incremental step test, so it seemed to be Masing material at the stabilized block. Cyclic hardening was successfully described in the increasing sequence of the strain amplitude in 5-step test. But, the slight cyclic softening followed by higher strain amplitude would not be able to simulate by'modified overlay model'. However, the discrepancy induced was very small between the calculated hystereses and the experimental ones. In conclusion,'Modified overlay model'was proved to be appropriate in strain range of 0.35％~ 1.0％..0％.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 춘계학술대회 논문집
• /
• pp.42-47
• /
• 1997

In this study, the drawing characteristics of circular drawbead are examined with the plane strain elastic-plastic FE Method by varying the process variables such as friction coefficient, drawbead radius, and closing depth. Numerical analysis are carried out by 2-D elastic-plastic F.E.M. The results are compared with the existing experimental results about the drawing force, the die clamping force, and the strain distribution of upper and lower sheet faces

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 봄 학술발표회 논문집
• /
• pp.181-188
• /
• 1994

Generally, the structural material shows rate dependent behaviors, which require to constitute different strain-stress relations according to strain rates. Conventional rate- independent constitutive equations used in general purpose finite analysis programs are inadequate for dynamic finite strain problems. In this paper, a rate dependent constitutive equation for elastic-plastic material was developed. The plastic stretch rate was modeled based on slip model with dislocation velocity and density so that there is no yielding condition, and no loading conditions. Non-linear hardening rule was also introduced for finite strain. Material constants of present constitutive equation were determined by experimental data of mild steel. The constitutive equation was applied to uniaxile tension. It was appeared that the present constitutive equation well simulates rate dependent behaviors of mild steel.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 1998년도 춘계 학술논문발표회 논문집
• /
• pp.89-97
• /
• 1998

In this study, under large scale yielding conditions crack propagation is found to governed by parameters based on the J-integral or on the crack opening displacement. But initiation of crack propagation of ductile material seems to be controlled by just on parameter that is the strain. The relationship between the critical value of J-integral and the local fracture strain in uniaxial tensile test in the region of maximum reduction in area. Therefore, the fundamental theorectical equation by the proposed elastic-plastic fracture toughness and the local fracture strain has a merit. in comparison with the ASTM method, which can measure by using the load-displacement curve and the specimens in tenslie test.

• 한국안전학회지
• /
• 제13권4호
• /
• pp.25-33
• /
• 1998

In this study, under large scale yielding conditions crack propagation is found to governed by parameters based on the J-integral or on the crack opening displacement. But initiation of crack propagation of ductile material seems to be controlled by just on parameter that is the strain. The relationship between the critical value of J-integral and the local fracture strain in uniaxial tensile test in the region of maximum reduction in area. Therefore, the fundamental theoretical equation by the proposed elastic-plastic fracture toughness and the local fracture strain has a merit, in comparison with the ASTM method, which can measure by using the load-displacement curve and the specimens in tensile test.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.190-193
• /
• 2004

Ever since the ideal forming theory has been developed fur process design purposes, application has been limited to sheet forming and, for bulk forming, to two-dimensional steady flow. Here, application for the non-steady case was performed under the plane-strain condition based on the theory previously developed. In the ideal flow, material elements deform following the minimum plastic work path (or mostly proportional true strain path) so that the ideal plane-strain flow can be effectively described using the two-dimensional orthogonal convective coordinate system. Besides kinematics, for a prescribed final part shape, schemes to optimize a preform shape out of a class of initial configurations and also to define the evolution of shapes and boundary tractions were developed. Discussions include the two problematic issues on internal tractions and the non-monotonous straining. For demonstration purposes, numerical calculations were made for a bulk part under forging.

• 한국산업융합학회 논문집
• /
• 제10권2호
• /
• pp.81-88
• /
• 2007

In case of an urban tunnel, the displacement of ground base controls the tunnel design because it is built on shallow and unconsolidated ground many times. There are more insufficiency to describe the ground movement which coincides in the measured result of the situ because the design of an urban tunnel is dependent on the method of numerical analysis used to the existing elastic and elasto-plastic models. We studied about the prediction for the ground movement of a shallow tunnel in unconsolidated ground, mechanism of collapse, and settlement. Also this paper shows comparison with the existing elastic and elasto-plastic model using the unlinear analysis of the strain-softening model. We can model the real ground movement as the increasement of ground surface inclination or occurrence of shear band by using strain-softening model for the result of ground movement of an urban NATM tunnel.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.141-149
• /
• 2002

Most of mechanical failures are caused by repeated loadings and therefore they are strongly related to fatigue. To avoid the failures caused by fatigue, determination of an optimal shape of a structure is one of the very important factors in the initial design stage. Shape optimization for three types of specimens, which are very typical ones in opening mode in fracture mechanics, was accomplished by the linear elastic fracture mechanics and the growth-strain method in this study. The linear elastic fracture mechanics was used to estimate stress intensity factors and fatigue lives. And the growth-strain method was used to optimize the shape of the initial shape of the specimens. From the results of the shape optimization, it was concluded that shapes of three types of specimens optimized by the growth-strain method prolong their fatigue lives very much.