• Steel and Composite Structures
• /
• v.22 no.1
• /
• pp.91-112
• /
• 2016

In this paper, post-buckling behavior of sandwich plates with functionally graded (FG) face sheets under uniform temperature rise loading is examined based on both sinusoidal shear deformation theory and stress function. It is supposed that the sandwich plate is in contact with an elastic foundation during deformation, which acts in both compression and tension. Thermo-elastic non-homogeneous properties of FG layers change smoothly by the variation of power law within the thickness, and temperature dependency of material constituents is considered in the formulation. In the present development, Von Karman nonlinearity and initial geometrical imperfection of sandwich plate are also taken into account. By employing Galerkin method, analytical solutions of thermal buckling and post-buckling equilibrium paths for simply supported plates are determined. Numerical examples presented in the present study discuss the effects of gradient index, sandwich plate geometry, geometrical imperfection, temperature dependency, and the elastic foundation parameters.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.8
• /
• pp.880-888
• /
• 2007

This article describes the load capability of bending piezoelectric actuators with a thin sandwiched PZT plate in association with the stored elastic energy induced by an increased dome height after a curing process. The stored elastic energy within the actuators is obtained via a flexural mechanical bending test. The load capability is evaluated indirectly in terms of an actuating displacement with a load of mass at simply supported and fixed-free boundary conditions. Additionally, a free displacement under no load of mass is measured for a comparison with an actuating displacement. The results reveal that an actuator with a top layer having a high elastic modulus and a low coefficient of thermal expansion exhibits a better performance than the rest of actuators in terms of free displacement as well as actuating displacement due to the formation of the large stored elastic energy within the actuator system. When actuators are excited at AC voltage, the actuating displacement is rather higher than the free displacement for the same actuating conditions. In addition, the effect of PZT ceramic softening results in a slight reduction in the resonance frequency of each actuator as the applied electric field increases. It is thus suggested that the static and dynamic actuating characteristics of bending piezoelectric composite actuators with a thin sandwiched PZT plate should be simultaneously considered in controlling the performance.

• Journal of Information Display
• /
• v.12 no.1
• /
• pp.23-27
• /
• 2011

The correlation between the temporal and spatial variations of the elastic constant and temperature change was examined for a light guide plate (LGP) adopted in the edge-lit light-emitting-diode backlight for mobile applications, using the micro- Brillouin light scattering method. The velocity of sound and the elastic constant $C_{11}$ of an LGP made from bisphenol-A polycarbonate (PC) were investigated as functions of temperature, time, and position on the LGP. The temporal variation of $C_{11}$ exhibited an exponential decay, while the spatial variation of $C_{11}$ reflected the temperature distribution on the LGP. The glass transition temperature of the PC LGP was found to be located at $155^{\circ}C$. The result showed that systematic transformation between the elastic property and the temperature is possible and that the temperature distribution on the bulk LGP can be accurately probed via the present experiment method, without using any special temperature measurement equipment.

• Structural Engineering and Mechanics
• /
• v.90 no.4
• /
• pp.391-401
• /
• 2024

The present study focuses on the effect of extension-bending coupling on the elastic stability (buckling) of laminated composite plates. These plates will be loaded under uni-axial or bi-axial in-plane mechanical loads, especially in the orthotropic or anti-symmetric cross-angle cases. The main objective is to find a limit where we can approximate the elastic stability behavior of angularly crossed anti-symmetric plates by the simple behavior of specially orthotropic plates. The contribution of my present study is to predict the explicit effect of extension-flexion coupling on the elastic stability of this type of panel. Critically, a parametric study is carried out, involving the search for the critical buckling load as a function of deformation mode, aspect ratio, plate anisotropy ratio and finally the study of the effect of lamination angle and number of layers on the contribution of extension-flexure coupling in terms of plate buckling stability. We use first-order shear deformation theory (FSDT) with a correction factor of 5/6. Simply supported conditions along the four boundaries are adopted where we can develop closed-form analytical solutions obtained by a Navier development.

• Journal of the Korean Institute of Navigation
• /
• v.20 no.1
• /
• pp.47-58
• /
• 1996

The use of high tensile steel plates is increasing in the fabrication of ship and offshore structures. The main portion of ship structure is usually composed of stiffened plates. In these structures, plate buckling is one of the most important design criteria and buckling load may usually be obtained as an eigenvalue solution of the governing equations for the plate. To use the high tensile steel plate effectively, its thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. When the panel elastic buckling is allowed, it is necessary to get precise understandings about the post-buckling behaviour of thin plates. It is well known that a thin flat plate undergoes secondary buckling after initial buckling took place and the deflection of the initial buckling mode was developed. From this point of view, this paper discusses the post-buckling behaviour of thin plates under thrust including the secondary buckling phenomenon. Series of elastic large deflection analyses were performed on rectangular plates with aspect ratio 3.6 using the analytical method and the FEM.

• Structural Engineering and Mechanics
• /
• v.36 no.6
• /
• pp.669-678
• /
• 2010

In general means, the stress concentration problem of elastic plate with a rectangular hole can be investigated by numerical methods, and only approximative results are derived. This paper deduces an analytical study of the stress concentration due to a rectangular hole in an elastic plate under bending loads. Base on classical elasticity theory and FEM applying the U-transformation technique, the uncoupled governing equations with 3-DOF are established, and the analytical displacement solutions of the finite element equations are derived in series form or double integral form. Therefore, the stress concentration factor can then be discussed easily and conveniently. For the plate subjected to unidirectional bending loads, the non-conforming plate bending element with four nodes and 12-DOF is taken as examples to demonstrate the application of the proposed method. The inner force distribution is obtained. The solutions are adequate for the condition when the hole is far away from the edges and the thin plate subjected to any transverse loadings.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.3
• /
• pp.172-177
• /
• 2003

This paper investigates the effect of reinforced plate on the deflection of the rectangular plate, when the rectangular plate is reinforced with rectangular rigid body at the centroid of the plate. For two boundary conditions such as simple supported and clamped boundary This study derives deflection formula of reinforced plates with three kinds of the aspect ratio of a rectangular plate with respect to the elastic modulus ratio and the length ratio of rigid body using the least square method. The results are as follows: 1. As the elastic modulus ratio r$_{e}$$\geq$ 1000, the maximum deflection with respect to the length ratio r$_{1}$ converges into constant value. 2. Deflection formula with respect to the length ratio r$_{1}$ is derived as the third order polynomial.l.

• Steel and Composite Structures
• /
• v.31 no.4
• /
• pp.419-426
• /
• 2019

In this paper, buckling analyses of composite plate reinforced by Graphen platelate (GPL) is studied. The Halphin-Tsai model is used for obtaining the effective material properties of nano composite plate. The nano composite plate is modeled by Third order shear deformation theory (TSDT). The elastic medium is simulated by Winkler model. Employing nonlinear strains-displacements, stress-strain, the energy equations of plate are obtained and using Hamilton's principal, the governing equations are derived. The governing equations are solved based on Navier method. The effect of GPL volume percent, geometrical parameters of plate and elastic foundation on the buckling load are investigated. Results showed that with increasing GPLs volume percent, the buckling load increases.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.10a
• /
• pp.166-173
• /
• 2000

This paper describes the method of evaluating the elastic modulus of soil medium by using the Retangular Plate Loading Test. The foundaton is considered to be the elastic half-space. The stiffness matrix of elastic half space is drived using Boussinesq's analytical soulution. A numerical examples are presented to verify the validity of this procedure. Also, the numerical results are compared with those of the existing study results. The procedure proposed in this theses can be applied to the design of concrete paving resting on the elastic foundation

• Structural Engineering and Mechanics
• /
• v.28 no.6
• /
• pp.635-658
• /
• 2008

An application is presented of a modified Vlasov model to the free vibration analysis of plates resting on elastic foundations. The effects of the subsoil depth, the ratio of the plate dimensions, the ratio of the subsoil depth to the plate dimension in the longer direction, and the value of the vertical deformation parameter within the subsoil on the frequency parameters of plates on an elastic foundation are investigated. This analysis has been caried out by the aid of a computer program. The first ten frequency parameters are presented in tabular and the graphical forms to evaluate the effects of the parameters considered in this study. Then mode shapes corresponding to the first six of the frequency parameters are given in graphs. It is concluded that the effect of the subsoil depth on the frequency parameters of the plates on an elastic foundation is generally larger than those of the other parameters considered in this study.