• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.157-160
• /
• 2003

Honeycomb sandwich composite structures have been widely used in aircraft and military industry because of light weight and high stiffness. Accurate mechanical properties of honeycomb materials are needed for analysis of sandwich composites. In this study, theoretical formula for elastic modulus of honeycomb materials was established considering bending and axial deformations of their walls. Finite-element analysis results were compared with theoretical ones of the longitudinal and transverse moduli of honeycomb materials. Consequently, the mechanical properties of honeycomb materials could be analytically predicted.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.210-212
• /
• 2003

Finite element analysis of welding processes, which entail phase evolution, heat transfer and deformation, is considered in this paper. Attention focuses on numerical implementation of the thermo-elastic-plastic constitutive equation proposed by Leblond et al in consideration of the transformation plasticity. Based upon the multiplicative decomposition of deformation gradient, hyperelastic formulation is employed for efficient numerical integration, and the algorithmic consistent moduli for elastic-plastic deformations including transformation plasticity are obtained in the closed form. The convergence behavior of the present implementation is demonstrated via a couple of numerical example.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.37-42
• /
• 2001

This paper presents the improved elastic modulus equation more appropriate to predict the modulus of elasticity of structural elements designed and made by high-strength concrete. To propose the elastic modulus equation, more than 300 laboratory specimen tests having the range of 5n to 800kgf/$cm^{2}$ in concrete compressive strength were conducted and analyzed statistically. The equation derived in terms of empirical constant, the elastic moduli of coarse aggregate and mix proportions. Comparison of the proposed elastic modulus equation with the previously suggested equations in the ACI363R, and New-RC were also presented to demonstrate the applicability to practice.

• Computers and Concrete
• /
• 제16권1호
• /
• pp.125-140
• /
• 2015

This paper describes the numerical calculation of elastic properties of a simulated microstructure of cement paste from very early age, when most previous models fail to give accurate results. The development of elastic properties of tricalcium silicate pastes was calculated by discretising a numerical resolution-free 3D vector microstructure to a regular cubic mesh. Due to the connections formed in the microstructure as an artefact of the meshing procedure, the simulated elastic moduli were found to be higher than expected. Furthermore, the percolation of the solids was found to occur even before hydration started. A procedure to remove these artefacts, on the basis of the information available in the vector microstructures was developed. After this correction, a better agreement of the experimental results with calculations was obtained between 20% and 40% hydration. However, percolation threshold was found to be delayed significantly. More realistic estimates of percolation threshold were obtained if either flocculation or a densification of calcium silicate hydrate with hydration was assumed.

• 한국지진공학회논문집
• /
• 제3권4호
• /
• pp.95-100
• /
• 1999

암석 코아의탄성계수 측정에 동적방법은 잘 사용되지 않을뿐만아니라 그 값은 설계에 많이 사용되지 않는다 그이유는 동적으로 결정한 탄성계수 값이 정적으로 결정된 값보다 매우 큰 것 (약 10배)으로 인식되기 때문이다. 이논문에서는 암석 코아의 동적과 정적 시험결과를 제시하였다 도출괸 결과는 :1) 실내탄성파시험으로 매우 일관성 있는 탄성계수가 결정되고 2) 변형율에 따른 암석 코아의 비선형 변형특성의 잠정적 모델이 제시되었다.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.613-625
• /
• 2016

Contact interaction of a beam (flexible element) with an elastic half-plane is considered, when a soft inhomogeneous (functionally graded) interlayer is present between them. The beam is bent under the action of a distributed load applied to the surface and a reaction of the elastic interlayer and the half-space. Solution of the contact problem is obtained for different values of thickness and parameters of inhomogeneity of the layer. The interlayer is assumed to be significantly softer than the underlying half-plane; case of 100 times difference in Young's moduli is considered as an example. The influence of the interlayer thickness and gradient of elastic properties on the distribution of the contact stresses under the beam is studied.

• Structural Engineering and Mechanics
• /
• 제78권3호
• /
• pp.281-296
• /
• 2021

This article analyzed the modulus degradation of concrete subjected to multi-level compressive cyclic loading. The evolution of secant elastic modulus is investigated based on measurements from top loading platen and LVDT in the middle part of concrete. The difference value of the two secant elastic moduli is reduced when close to failure and could be used as a fatigue failure precursor. The fatigue hardening is observed for concrete during cyclic loading. When the maximum stress is smaller the fatigue hardening is more obvious. The slight increase of maximum stress will lead to the "periodic hardening". The tangent elastic modulus shows a specific "bowknot" shape during cyclic loading, which can characterize the hysteresis of stress-strain and is influenced by the cyclic loading stresses. The deterioration of secant elastic modulus acts a similar role with respect to the P-wave speed during cyclic loading, can both characterize the degradation of the concrete properties.

• 한국지반공학회논문집
• /
• 제35권1호
• /
• pp.5-15
• /
• 2019

본 연구에서는 제주도 북동부 육 해상 및 북서부 육상에 위치한 현무암반에 대한 공내재하시험으로부터 계측된 변형계수와 RQD 및 RMR의 관계를 각각 살펴보았으며, 기존의 경험식들로부터 추정된 변형계수 값과 비교 분석하였다. 뿐만 아니라, 속도검층시험을 통하여 산정된 탄성파 속도비 및 동적 포아송 비와 변형계수의 관계에 대해서도 각각 살펴보았다. 그 결과, 다공성 구조 및 층상 구조가 특징인 제주도 현무암반의 경우, RQD 값만을 이용한 암반등급의 결정, 변형계수 계측방법의 선정 및 변형계수의 추정은 부적절하며, 최소한 RMR을 통하여 암반등급을 결정하고, 변형계수를 추정하는 것이 바람직하다는 것을 알 수 있었다. RMR을 이용한 기존의 변형계수 추정식은 제주도 현무암반의 변형계수에 비해 큰 값을 예측하는 경향을 보였으며, 탄성파 속도비 및 동적 포아송 비와 변형계수는 서로 정성적인 특성이 일치하는 관계에 있었다. 그리고, 적절한 제주도 현무암반의 변형계수를 추정하기 위한 RMR과 탄성파 속도비를 이용한 변형계수 추정식을 각각 제시하였다.

• 한국지반공학회지:지반
• /
• 제7권4호
• /
• pp.25-34
• /
• 1991

본 연구에서는 KS규정에 의한 CBR 값과 삼축압축시험을 이용하여 구한 탄성계수와의 관계를 구명하였다. 시료는 통일분류법에 의하여 5가지로 분류된 전국고속도로 15개 지점에서 채취한 노상 토재료를 선정하였으며 각 시료에 대하여 CBR시험과 삼축압축시첩을 병행하여 실시하였다. 압 밀 비배수 삼축압축시헙 (CU triaxial teat)을 실시하여 얻어진 응력과 변형률의 관계로부터 탄성 계수를 산정하였으며 노상에 발생되는 모든 응력상태에 적용할 수 있도록 일반화하기 위하여 삼축 압축시험시 구속음력은 3가지로 달리하여 실험하였다. 실험결과로부터 얻은 수정 CBR값과 탄성계수간의 상관관계를 회귀분석하여, 구속음력과 유효 평균주응력의 함수로 표현된 탄성계수와 수정 CBR값과의 관계식들을 제안하였다. 또한 D-2 다짐에 의하여 얻어진 최대 건조밀도와 수정 CBR값과의 상관관계식을 제안하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.151-151
• /
• 2011

Large amounts of natural gas, mainly methane, in the form of hydrates are stored on continental margins. When gas hydrates are dissociated by any environmental trigger, generation of excess pore pressure due to released free gas may cause sediment deformation and weakening. Hence, damage on offshore structures or submarine landslide can occur by gas hydrate dissociation. Therefore, geotechnical stability of gas hydrate bearing sediments is in need to be securely assessed. However, geotechnical characteristics of gas hydrates bearing sediments including small-strain elastic moduli have been poorly identified. Synthesizing gas hydrate in natural seabed sediment specimen, which is mainly composed of silty-to-clayey soils, has been hardly attempted due to their low permeability. Moreover, it has been known that hydrate loci in pore spaces and heterogeneity of hydrate growth in specimen scale play a critical role in determining physical properties of hydrate bearing sediments. In the presented study, we synthesized gas hydrate containing sediments in an instrumented oedometric cell. Geotechnical and geophysical properties of gas hydrate bearing sediments including compressibility, small-strain elastic moduli, elastic wave, and electrical resistivity are determined by wave-based techniques during loading and unloading processes. Significant changes in volume change, elastic wave, and electrical resistivity have been observed during formation and dissociation of gas hydrate. Experimental results and analyses reveal that geotechnical properties of gas hydrates bearing sediments are highly governed by hydrate saturation, effective stress, void ratio, and soil types as well as morphological feature of hydrate formation in sediments.