• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.125-127
• /
• 1998

Superconducting tape is being developed for electrical equipment such as superconducting transformers and generators. AC loss reduction is primary concern in the development of such high-efficiency equipment. AC losses in Bi-2223 silver-sheathed tapes, both single and multi-filamentary, were investigated by means of AC magnetization techniques. The results were compared with the hysteresis loss equation based on Bean model and the eddy current loss equation. The AC loss, of the mono-filamentary tape was the hysteresis. On the contrary, the AC loss of the multi-filamentary tape was substantially dominated by the eddy current loss in the Ag matrix.

• Journal of Advanced Marine Engineering and Technology
• /
• v.10 no.3
• /
• pp.94-106
• /
• 1986

Since the oil shock of '70s the engine makers have developed new types of diesel engine with low fuel consumption. There is an obvious tendency towards the use of poorer quality fuels, such as the residual oil from chemical processes of refinery. The shaft driving generators is also widely adopted on behalf of the auxiliary diesel engines, which are driving on the expensive diesel oil and have high fuel oil consumption rates, and some mania propulsion diesel engines are equipped with reduction gear systems to get better propulsive efficiency by slower propeller revolutions. The propulsion shafting system equipped with the shaft driving generator or the geared diesel engine shafting system has flexible couplings, and it requires extensive investigations of the torsional vibration and torque fluctuation in order to ensure the acceptable operation range in service. The characteristics of misfiring must be especially examined for the high viscosity fuels to be used. Both torsional vibration and fluctuating torque resulted from misfiring, should be examined for thier effects on the flexible coupling and propulsion shafting system. This paper is to investigate and solve the above mentioned problems which must be predicted on the design-stage of marine propulsion shafting system. A computer program is developed to calculate the indicated diagram, fluctating torque and torsional vibration for both normal and misfiring conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.3
• /
• pp.267-273
• /
• 2013

Recently, turbine-generators have been replaced for the integrity reinforcement and the efficiency improvement, also, the blade's failures of LP turbines due to torsional vibration have been reported. Excessive torsional vibrations can result in failures of components. The severity of torsional oscillations and stress depends upon the separation margin between the excitation frequencies and torsional natural frequencies. Therefore it is needed to measure the torsional natural frequencies after replacement of the components to conform the separation margin of torsional natural frequencies. In this study torsional vibration measurements were performed after LP turbine and generator replacement and the torsional natural frequencies for the turbine-generator train were calculated to evaluate the effects of generator replacement on torsional natural frequencies of turbine-generator train. It is expected that these evaluation results will be used effectively to identify the root causes of torsional vibration problems.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.4B no.3
• /
• pp.146-152
• /
• 2004

Cost effective simulation schemes for Wind Power Generation Systems (WPGS) considering wind turbine types, generators and load capacities have been strongly investigated by researchers. As an alternative, a true weather condition based simulation method using a real-time digital simulator (RTDS) is experimented in this paper for the online real-time simulation of the WPGS. A stand-alone WPGS is, especially, simulated using the Simulation method for WPGS using Real Weather conditions (SWRW) in this work. The characteristic equation of a wind turbine is implemented in the RTDS and a RTDS model component that can be used to represent any type of wind turbine in the simulations is also established. The actual data related to weather conditions are interfaced directly to the RTDS for the purpose of online real-time simulation of the stand-alone WPGS. The outcomes of the simulation demonstrate the effectiveness of the proposed simulation scheme. The results also signify that the cost effective verification of efficiency and stability for the WPGS is possible by the proposed real-time simulation method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1178-1182
• /
• 2004

This paper presents web-based virtual laboratory system for electronic and digital circuit experiments. Through our virtual laboratory, the learners will be capable of learning the concepts and theories related to circuit experiments and how to operate virtual experimental equipments such as multimeters, function generators, digital oscilloscopes, DC power suppliers and bread board etc. The proposed virtual laboratory system is composed of important components: Principle Classroom to explain the concepts and theories of electronic and digital circuit operations, Simulation Classroom to provide a web-based simulator to the learners, Virtual Experiment Classroom to provide interactive multimedia contents about the syllabus of off-line laboratory class, Assessment Classroom, and Management System. With the aid of the management System every classroom is organically tied together collaboration to achieve maximum learning efficiency. We have obtained several affirmative effects such as high learning standard, reducing the total experimental hours and the damage rate for experimental equipments.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1261-1268
• /
• 2013

This study proposes a voltage and reactive coordinative control strategy with distributed generator (DG) in a distribution power system. The aim is to determine the optimum dispatch schedules for an on-load tap changer (OLTC), distributed generator settings and all shunt capacitor switching on the load and DG generation profile in a day. The proposed method minimizes the real power losses and improves the voltage profile using squared deviations of bus voltages. The results indicate that the proposed method reduces the real losses and voltage fluctuations and improve receiving power factor. This paper proposes coordinated voltage and reactive power control methods that adjust optimal control values of capacitor banks, OLTC, and the AVR of DGs by using a voltage sensitivity factor (VSF) and dynamic programming (DP) with branch-and-bound (B&B) method. To avoid the computational burden, we try to limit the possible states to 24 stages by using a flexible searching space at each stage. Finally, we will show the effectiveness of the proposed method by using operational cost of real power losses and voltage deviation factor as evaluation index for a whole day in a power system with distributed generators.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.4
• /
• pp.180-185
• /
• 2012

Tidal power is one of new and renewable energy sources. The seawater is stored inside a tidal embankment built at the mouth of a river or bay, where tides ebb and flow. The water turbine-generators produce power by exploiting the gap in the water level between the water outside and inside the embankment. Tidal power plant is a large plant that is installed on the sea. And then, the facility's operations and a separate control system for monitoring and maintenance is required. However, this plant predictive control of building systems and technologies have been avoided the transfer of technology from advanced global companies. Accordingly, the control system for core technology development and localization is urgently needed. This paper presents modeling and simulation using by PSS/E about generator, governor, exciter, and power system stabilizer for control system in Sihwa tidal power plant to improve the efficiency and develope of core technology. And the dynamic characteristics of governor and exciter were analyzed.

• Progress in Superconductivity and Cryogenics
• /
• v.26 no.1
• /
• pp.25-30
• /
• 2024

High-temperature superconducting rotors offer advantages in terms of output-to-weight ratio and efficiency compared to conventional phase conduction motors or generators. The rotor can be cooled by conduction cooling, which attaches a cryocooler, and by refrigerant circulation, which uses circulating liquid or gas neon, helium and hydrogen. Recent work has focused on environmental issues and on high-temperature superconducting motors cooled with liquid hydrogen that can be combined with fuel cells. However, to ensure smooth supply and return of the cryogenic cooling fluid, a cryogenic rotational coupling between the rotating and stationary parts is necessary. Additionally, the development of a sealing structure to minimize fluid leakage applicable to the coupling is essential. This study describes the design and performance evaluation of a non-contact sealing method, specifically a labyrinth seal, which avoids power loss and heat load caused by friction in contact sealing structures. The seal design incorporates a spiral flow path to reduce leakage using centrifugal force, and computational fluid dynamics (CFD) simulations were conducted to analyze the flow path and rotational speed. A performance evaluation device was configured and employed to evaluate the designed seal. The results of this study will be used to develop a cryogenic rotational coupling with supply and return flow paths for cryogenic applications.

• Journal of IKEEE
• /
• v.15 no.1
• /
• pp.96-103
• /
• 2011

This paper deals with the characteristic analysis of the integrated power system applied for the electric propulsion ships. This includes the electric power system modeling which is accomplished with the electric power network mainly composed of generators, switchboards, variable frequency devices, electric motors, and etc. In addition, performance comparison between the permanent magnet synchronous motor (PMSM) and the induction motor (IM) for 3.7MW ship propulsion has been done. In order to investigated the main performance of propulsion motor, a coupled model taking into account torque density, copper loss, iron loss, efficiency, power factor, and torque ripple using finite element analysis (FEA) has been employed.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2005.10a
• /
• pp.592-597
• /
• 2005

Biogas is widely accepted as one of renewable energy. Raw biogas can be used in internal combustion engines either spark ignition or diesel engines. Since the gas has relatively low calorific values, engine power also is lower than rated power values. Modified engines or biogas-specific engines have been utilized in order to increase efficiency. Recently, gas engine/generators are provided for various purposes. They are mostly for LPG or natural gas. When biogas is fueled to the gas engines, de-rating is inevitable due to its lower calorific values. Meanwhile, massively produced commercial gas engines are more competitive in terms of initial investment for engines, compared to biogas-specific engines. Then, the characteristics of the commercial engine and power generation should be understood for better operation. A 5kW gas engine/generator(natural gas) was tested for determining an allowable maximum concentration of $CO_2$ in synthetic biogas, with respect to engine stating, power generation. Experimental results indicated that about 65% of methane concentration is required to start the gas engine. At this condition, the power generated was about 3 kW. It is about 60% of the nominal power, which is similar to the ratio of calorific values.