• 한국전자파학회논문지
• /
• 제14권2호
• /
• pp.96-103
• /
• 2003

본 논문에서는 모노펄스 레이다용 cavity-backed 마이크로스트립 안테나를 설계 및 제작하고, 제작된 안테나의 측정 결과를 분석하여 레이다 시스템에 잘 적용될 수 있음을 보였다. 일반적인 마이크로스트립 안테나의 방위각 빔폭에 비해, 시스템에서 요구하는 방위각 빔폭이 상당히 넓기 때문에, 마이크로스트립 패치의 폭을 상당히 줄였으며, 이에 따른 대역폭의 감소는 유효 기판 두께를 증가시킴으로 보상하였다. 또한 각도에 따른 안테나 이득 변화에 대한 탐지 거리와 탐지 확률을 계산함으로써, 제작된 안테나가 이러한 레이다 시스템에 잘 적용될 수 있음을 보였다.

• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.53-62
• /
• 2005

This study presents the NDE (non-destructive evaluation) technique for detecting the loosened bolts on joint steel structures on the basis of TOF (time of flight) and amplitudes of Lamb waves. Probabilistic neural network (PNN) technique which is an effective tool for pattern classification problem was applied to the damage estimation using PZT induced Lamb waves. Two kinds of damages were introduced by dominant damages (DD) which mean loosened bolts within the Lamb waves beam width and minor damages (MD) which mean loosened bolts out of the Lamb waves beam width. They were investigated for the establishment of the optimal decision boundaries which divide each damage class's region including the intact class. In this study, the applicability of the probabilistic neural networks was identified through the test results for the damage cases within and out of wave beam path. It has been found that the present methods are very efficient and reasonable in predicting the loosened bolts on the joint steel structures probabilistically.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.521-526
• /
• 2001

The flexural behavior of a strengthened beam that is a reinforced concrete beam with externally bonded carbon fiber sheets, is theoretically and experimentally investigated. A rectangular beam having a width of 20cm depth of 30cm and effective depth of 25cm is chosen. In order to have a variety of beams analyzed, three reinforcement ratios are chosen for the analysis: 1)$\frac{1}{2}$$\rho$$_{max}$, which is the most suitable reinforcement ratio for deflection consideration and the highest reinforcement ratio for practical designing beams as well; 2)$\rho$$_{max}$, which is the lowest reinforcement ratio for design purposes; and 3)the reinforcement ratio halfway from 1) and 2). Carbon fiber sheets with width of 15cm are externally bonded at the bottom fiber of the beam. The effect of the amount of carbon fiber sheets varying from 1 to 4 plies on the flexural capacity of the strengthened beam are also examined. Yield loads, ultimate loads, and flexural rigidities of the strengthened beam from the experimental results are composed with theoretical ones.nes.

• 한국해양공학회지
• /
• 제15권4호
• /
• pp.1-7
• /
• 2001

Mainly, Floating Breakwaters (FBs) have been constructed in many coastal regions due to the advantages of the coastal environment and construction cost. In general, the FB becomes fixed or its width broadened because the movement of the FB comes to be large and its the wave control function lower for the long period incident waves. This study discusses the wave control function of two-rowed Fixed Floating Breakwater (FFBs) that have narrower width than that of the one-rowed FFB by using numerical approach. Boundary Element Method (BEM) based on the Green formula and Eigenfunction Expansion Method (EEM) are applied to evaluate the three-dimensional wave transformation near the wave fields of two-rowed FFBs. The validity of the present study is confirmed by comparing it with the results of Ijima et al. (1974) and Yoshida et al. (1992) for the one-rowed Fixed Floating Structure. It is revealed that the wave control function of two-rowed FFBs is more effective than that of the one-rowed FFB.

• 한국측량학회지
• /
• 제33권6호
• /
• pp.605-614
• /
• 2015

Drone imaging, which is more cost-effective and controllable compared to airborne LiDAR, requires a low-cost camera and is used for capturing color images. From the overlapped color images, we produced two high-resolution digital surface models over different test areas. After segmentation, we performed tree identification according to the method proposed by , and computed the tree height and the canopy crown size. Compared with the field measurements, the computed results for the tree height in test area 1 (coniferous trees) were found to be accurate, while the results in test area 2 (deciduous coniferous trees) were found to be underestimated. The RMSE of the tree height was 0.84 m, and the width of the canopy crown was 1.51 m in test area 1. Further, the RMSE of the tree height was 2.45 m, and the width of the canopy crown was 1.53 m in test area 2. The experiment results validated the use of drone images for the extraction of a tree structure.

• Steel and Composite Structures
• /
• 제15권6호
• /
• pp.605-621
• /
• 2013

CFRP strips are widely used nowadays for repair/strengthening or capacity increase purposes. Sharp bending at the ends of the CFRP strips is frequently encountered at these applications. In this study, Reinforced Concrete (RC) beam specimens that were produced with 10 MPa compression strength concrete were strengthened by using bonded CFRP strips with end anchorages to tension region. The parameters that were investigated in this study are the width of the strip, the number of applied fan anchorages and whether additional layer of CFRP patch is used or not at the strip ends. Specimens were strengthened with 100 mm wide CFRP strips with one or two anchorages at the ends. In addition CFRP patch with two and three anchorages at the ends were tested for investigating the effect of the patches. Specimens that were strengthened with three anchorages at the ends with patches were repeated with 60 and 80 mm wide CFRP strips. The most successful result was obtained from the specimen that was strengthened with 80 mm wide CFRP strips with 3 end anchorages and patches among the others at the experimental program. The numbers of anchorages that were applied to ends of CFRP strips were more effective than the width of the CFRP strips onto strength and stiffness of the specimens. Due to limited space at the ends of the strips at most three anchorages could be applied.

• 한국전기전자재료학회논문지
• /
• 제13권6호
• /
• pp.538-544
• /
• 2000

The laser patterning of sputter-deposited CoNdZr/Cu/CoNbZr multi-layered films had been tried using Nd:YAG laser. However generally it is very difficult to remove metal films because of their high reflectance of the laser on the surfaces. As a counterproposal for this problem authors for the first time tried to deposit energy-absorbing layers on the metal films and then irradiated the laser on the surfaces of energy-absorbing layers. Here the energy-absorbing layers consisted of laser energy-absorbing fine powders and binding polymers. Three kinds of powders for the energy-absorbing layers had been used to see the difference in the pattern formation with the degree of laser energy absorption. They were electrically conductive silver powders insulating BaTiO$_3$powder and semiconducting carbon powder. Remarkable difference in width of the formed pattern and the roughness of pattern edge were observed with the characteristic of the powder for the energy-absorbing layer. The pattern width using carbon paste was about three times larger than that using BaTiO$_3$paste. It was observed that the energy-absorbing layer with carbon was the most effective on this micro-patterning.

• 한국주거학회논문집
• /
• 제25권1호
• /
• pp.23-32
• /
• 2014

This research progressed space evaluation test with 3D simulation for exterior space of detached housing area among the Seoul spaces of child sex offense in 2010. Based on changing analysis on natural surveillance by spatial changes of each physical element, the purpose is to suggest effective construction planning measure for preventing child sex offense. The results of research are as follows. First, natural surveillance of space's height differences and width differences were compared and analyzed. As the result, footpath shows that stairs of slope didn't make lots of effects on visual block, not block of spatial moving, because of the difference of stair height. Also, in case of parking space, visual connection with footpath is expanded when designing pilotis rather than heightening floor height, so activities of exterior people could be seen more easily. Therefore, natural surveillance was higher. Second, natural surveillance of architectural elements by changes of footpath' width was compared and analyzed. As the result, openness of footpath should be secured rather than openness of architectural element. And, planning autonomy of architectural form could be more expanded when securing openness of footpath.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.910-912
• /
• 2006

Barrier ribs in plasma display panels (PDPs) function to maintain the discharge space between the glass plates as well as to prevent optical cross-talking. The barrier ribs currently employed are typically $300{\mu}m$ pitch, $110{\sim}120{\mu}m$ in height, with upper and lower widths of $50{\mu}m$ and $80{\mu}m$, respectively. It has been reported that barrier ribs can be fabricated by screen-printing, sand blasting, etching and photolithographic processes. In this study, photosensitive barrier rib pastes were formulated and systematically evaluated in terms of photolithographic process variables such as printing, drying, UV exposure, development and sintering. It was found that the use of UV absorbent, polymerization inhibitor and surfactant were very effective in controlling the width uniformity of barrier ribs in the photolithographic method of barrier rib patterning.

• 제어로봇시스템학회논문지
• /
• 제20권7호
• /
• pp.756-759
• /
• 2014

DC/DC converters are commonly used to generate regulated DC output voltages with high-power efficiencies from different DC input sources. The converters can be applied in the regenerative braking of DC motors to return energy back to the supply, resulting in energy savings for the systems at periodic intervals. The fundamental converter studied here consists of an IGBT (Insulated Gate Bipolar mode Transistor), an inductor, a capacitor, a diode, a PWM-IC (Pulse Width Modulation Integrated Circuit) controller with oscillator, amplifier, and comparator. The PWM-IC is a core element and delivers the switching waveform to the gate of the IGBT in a stable manner. Display of the DC/DC converter output depends on the IGBT's changes in the threshold voltage and PWM-IC's pulse width. The simulation was conducted by PSIM software, and the hardware of the DC/DC converter was also implemented. It is necessary to study the fact that the output voltage depends on the duty rate of D, and to compare the output of experimental result with the theory and the simulation.