• Wind and Structures
• /
• v.8 no.5
• /
• pp.357-372
• /
• 2005

Mean and extreme pressure distributions on a large cantilevered flat roof model are measured in a boundary layer wind tunnel. The largest peak suction values are observed from pressure taps beneath conical "delta-wing type" corner vortices that occur for oblique winds, then the characteristics and causes of the local peak suctions are discussed in detail. Power spectra of fluctuating wind pressures measured from some typical taps located at the roof edges under different wind directions are presented, and coherence functions of fluctuating pressures are also obtained. Based on these results, it is verified that the peak suctions are highly correlated with the conical vortices. Furthermore, according to the characteristics of wind loads on the roof, an aerodynamic solution to minimize the peak suctions by venting the leading edges and the corners of the roof is recommended. The experimental results show that the suggested strategy can effectively control the generation of the conical vortices and make a reduction of 50% in mean pressures and 25% in extreme local pressures at wind sensitive locations on the roof.

• Journal of Digital Convergence
• /
• v.12 no.11
• /
• pp.281-288
• /
• 2014

A method for edge detection using K-means clustering is proposed in this paper. The method is performed through there steps. Histogram equalizing is applied to the image for the uniformed intensity distribution. Pixels are clustered by K-means clustering technique. Then Sobel mask is applied to detect edges. Experiments showed that this method detected edges better than conventional method.

• Journal of Welding and Joining
• /
• v.17 no.3
• /
• pp.71-78
• /
• 1999

The welded metal bellows is commonly manufactured by welding pairs of washer-shaped discs of thin sheet metal stamped from strip stock in thickness from 0.025 to 0.254 mm. The discs, or diaphragms, are formed with mating circumferential corrugations. In this study, the diaphragms were welded by using a CW Nd: YAG laser to form metal bellows. The bellows was fixed on a jig and compressed axially, while Cu-rings were installed between belows edges for intimate contact of edges. The difference between the inner diameter of bellows and jig shaft causes an eccentricity, while the tolerance between motor shaft and jig shaft causes a wobble type motion. A vision sensor which is based on the optical triangulation was used for seam tracking. An image processing algorithm which can distinguish the image by bellows edge from that by Cu-ring was developed. The geometric relationship which describes the eccentricity and wobble type motion was modeled. The seam tracking using the image processing algorithm and the geometric modeling was performed successfully.

• Journal of the Korea Society of Computer and Information
• /
• v.20 no.9
• /
• pp.31-37
• /
• 2015

Symmetry is easily found in animals and plants as well as in artificial structures. It is useful not only for human cognitive process but also for image understanding by computer. Application areas include face detection and recognition, indexing of image database, image segmentation and detection, and analysis of medical images. The method used in this paper extracts edges, and the perpendicular bisector of any pair of selected edge points is considered to be a candidate axis of symmetry. The coefficients of the perpendicular bisectors are accumulated in the coefficient space. Axis of symmetry is determined to be the line for which the histogram has maximum value. This method shows good results, but the usefulness of the method is restricted because the amount of computation increases proportional to the square of the number of edges. In this paper, an acceleration method is proposed which performs $2^{2n}$ times faster than the original one. Experiment on 20 test images shows that the proposed method using level-3 image segmentation performs 63.9 times faster than the original method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.781-786
• /
• 2015

It is necessary for ferrite sheets to be fabricated with high packing density for excellent electrical properties and high strength. In this study, the relationship between the warpage and the packing density of ferrite green sheet, was investigated with amount variation of organic additives. With 0.4 wt% of dispersant, the packing density was about 48% and warpage appeared 0.5~1.3 mm high. With 1.4 wt% of dispersant, the packing density increased up to 57% and warpage appeared 0.8~2.1 mm high. With high packing density, warpage appeared along the edges of specimen, while with low packing density, deformation appeared over whole specimen inhomogeneously. It is thought that inhomogeneous deformation after sintering came from the inhomogeneity in green sheet prepared with badly dispersed slurry. With good homogeneity in green sheet from well-dispersed slurry, isotropic shrinkage is thought to have occurred along the distance from center to edges of specimen during sintering.

• The Journal of the Korea Contents Association
• /
• v.3 no.4
• /
• pp.23-28
• /
• 2003

This paper describes, in order to extract contour from topographic map image, an adaptive segment-length thresholding using a threshold depended on target image. First of all, after recognizing the primary symbols and detecting two edges from the projection histogram of the elevation value area, the threshold value is determined by the distance between the edges. Then, the subdivision is peformed by searching a branch point and erasing its neighboring Hack pixels. And contour components are extracted by segment-length thresholding. The experimental result shows that the final image contains non-contour component of 2.41% and contour one of 97.59%.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.770-772
• /
• 2013

Edges on the images are widely used in preprocessing in various areas including recognition and detection of the object. As generally known edge detection methods, there is a method using mask and these methods are Sobel, Prewitt, Roberts, Laplacian operator and etc. Implementation of these existing edge detection methods is simple. However, when processing the impulse noise added images, the properties of edge detection is not sufficient. Accordingly, in order to compensate for the weakness of existing edge detection methods and to detect strong edges on the images which were damaged by impulse noise, the edge detection algorithm using transformed mask was proposed in this paper.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.265-267
• /
• 2013

Edges include various important informations of the objects. These edges are being applied in numerous areas and there is a detection method using mask in existing edge detection methods. These existing edge detection methods are simple to realize. However, because the fixed mask is used, edge detection characteristics in complicated noise environments are somewhat unsatisfactory. Therefore, to compensate for the weakness in the existing detection methods, edge detection algorithm which uses the standard deviation of local mask and noise elimination was proposed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.10A
• /
• pp.1011-1020
• /
• 2002

The current paper presents an effective deblocking algorithm for block-based coded images using singularity detection in a wavelet transform. In block-based coded images, the local maxima of a wavelet transform modulus detect all singularities, including blocking artifacts, from multiscale edges. Accordingly, the current study discriminates between a blocking artifact and an edge by estimation the Lipschitz regularity of the local maxima and removing the wavelet transform modulus of a blocking artifact that has a negative Lipschitz regularity exponent. Experimental results showed that the performance of the proposed algorithm was objectively and subjectively superior.

• Computational Structural Engineering
• /
• v.10 no.1
• /
• pp.149-158
• /
• 1997

This paper presents the illustration of application under attached point mass to the special orthotropic plates with a pair of opposite edges simply supported and the other pair of opposite edges free. Design engineers need to calculate the natural frequencies of such elements but obtaining exact solution to such problems is very much difficult. Pretlove reported a method of analysis of beams with attached masses using the concept of effective mass. This method, however, is useful only for certain simple types of beam. Therefore, considering the method has been developed by D. H. Kim(1974) is simple, accurate, and very effective for the plates with arbitrary boundary conditions and irregular sections, this paper calculates the natural frequencies of composite laminated plate under attached point mass/masses.