• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.88-91
• /
• 2002

The two dimensional size effect of specimen gauge section (length x width) was investigated on the compressive behavior of a T300/924 [45/-45/0/90]3s, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a 30$\times$30, 50$\times$50, 70$\times$70, and 90mm$\times$90mm gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• Journal of the Korean Society of Costume
• /
• v.44
• /
• pp.181-199
• /
• 1999

The industry of modern clothing has deviated from the overflow of commercialism and the standardization and nowadays is going toward pursuing art, creativity, and high added value. This trend brings the return of the natural materials from the synthetic textiles and increases the value of old and handmade fabrics. Finally, the handmade-paper, which is a natural material, comes to be reconsidered as a new material for the clothing. Therefore, as the natural materials and the manufacture of handmade clothing are rising again, the qualitative improvement and globalization of clothing industry should be first realized through the developments of creative and various clothing materials and new expressing techniques. The above investigation and study have been synthesized and analyzed as follows: First, through the study on the origin of the paper clothing, its historical background and the process of its development, we've learned these two facts following : the paper clothing of the East in the past mostly had practiced meanings. On the other hand, in the West it had meanings which were raised the artist's emotions and beauty-consciousness to the artistic level by the various kinds of expressing methods. Second, handmade-paper was manufactured by the embedding method, which mixed mulberry pulp, gauze, corn, hair, sisal, silk and so on. It was found that handmade-paper had the affluent and proper texture as the clothing material and was be able to control the clarity through the variation of thickness. It was also confirmed that the creative and original texture with hand-worked molding beauty was obtained by the use of handmade-paper. Third, when the handmade-paper is used, the molding beauty of plane, relievo, and solid can be freely pursued, and various and effective molding conformation can be constructed by the effect of superposition and repetition. Also, because the maximum discretion from the various optional manufacturing methods is allowed, the molding beauty can be maximized when the clothes are manufactured with handmade-paper. Fourth, the gauze with strong drape was combined to overcome the stiffness and the tearing of the paper. As a result, the durability and the wearability of the paper were strengthened and thus the thus the applications as the clothing material were enlarged. In conclusion, in order to enhance the value, creativity, practicality, and artistic sense of the design for modern clothing, the clothes made of handmade-paper should be more studied. Moreover, for the generalization of paper clothes, the studies on the development of practical paper with paper with water resistance, post-treatment after dyeing, flexibility, and durability should be done. I really hope that this study will be the motive to provoke the possibility of handmade-paper as new clothing material in not only practical sense but also artistic sense.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.9
• /
• pp.3595-3604
• /
• 2015

Hepatocellular carcinoma (HCC) has been one of the most fatal malignant tumors worldwide and its associated morbidity and mortality remain of significant concern. Based on in-depth reviews of serological diagnosis of HCC, in addition to AFP, there are other biomarkers: Lens culinaris agglutinin-reactive AFP (AFP-L3), descarboxyprothrombin (DCP), tyrosine kinase with Ig and eprdermal growth factor (EGF) homology domains 2 (TIE2)-espressing monocytes (TEMs), glypican-3 (GPC3), Golgi protein 73 (GP73), interleukin-6 (IL-6), and squamous cell carcinoma antigen (SCCA) have been proposed as biomarkers for the early detection of HCC. The diagnosis of HCC is primarily based on noninvasive standard imaging methods, such as ultrasound (US), dynamic multiphasic multidetector-row CT (MDCT) and magnetic resonance imaging (MRI). Some experts advocate gadolinium diethyl-enetriamine pentaacetic acid (Gd-EOB-DTPA) MRI and contrast-enhanced US as the promising imaging madalities of choice. With regard to recent advancements in tissue markers, many cuting-edge technologies using genome-wide DNA microarrays, qRT-PCR, and proteomic and inmunostaining studies have been implemented in an attempt to identify markers for early diagnosis of HCC. Only less than half of HCC patients at initial diagnosis are at an early stage treatable with curative options: local ablation, surgical resection, or liver transplant. Transarterial chemoembolization (TACE) is considered the standard of care with palliation for intermediate stage HCC. Recent innovative procedures using drug-eluting-beads and radioembolization using Yttrium-90 may exhibit beneficial effects in HCC treatment. During the past few years, several molecular targeted agents have been evaluated in clinical trials in advanced HCC. Sorafenib is currently the only approved systemic treatment for HCC. It has been approved for the therapy of asymptomatic HCC patients with well-preserved liver function who are not candidates for potentially curative treatments, such as surgical resection or liver transplantation. In the USA, Europe and particularly Japan, hepatitis C virus (HCV) related HCC accounts for most liver cancer, as compared with Asia-Pacific regions, where hepatitis B virus (HBV) may play a more important role in HCC development. HBV vaccination, while a vaccine is not yet available against HCV, has been recognized as a best primary prevention method for HBV-related HCC, although in patients already infected with HBV or HCV, secondary prevention with antiviral therapy is still a reasonable strategy. In addition to HBV and HCV, attention should be paid to other relevant HCC risk factors, including nonalcoholic fatty liver disease due to obesity and diabetes, heavy alcohol consumption, and prolonged aflatoxin exposure. Interestingly, coffee and vitamin K2 have been proven to provide protective effects against HCC. Regarding tertiary prevention of HCC recurrence after surgical resection, addition of antiviral treatment has proven to be a rational strategy.

• Korean Journal of Environment and Ecology
• /
• v.26 no.6
• /
• pp.911-922
• /
• 2012

This study aim that definite the relationship between coastal environment and different sand bar communities, as well as to analyze their spatial distribution of barrier island in the Nakdong river estuary. Survey method follow by Braun-Blanquet(1965) and there a total of 118 relev$\acute{e}$'s were undertaken. Definition of the relationships between species and environmental variables with Canonical Correlation Analysis(CCoA) and that to applied these relev$\acute{e}$'s with the RIM(Kim and Kim, 2006) program and that to classification used the SYN-TAX 2000 program(Podani 1979). On the basis of about 118 phytosociological releve's, the vegetation of xeric and hydric type was arranged in twelve plant communities: Xeric type-Pinus thunbergii community,Vitex rotundifolia community, Carex pumila community, Imperata cylindrica var. koenigii community, Miscanthus sacchariflorus community and Calystegia soldanella community, Hydric type-Salix dependens-Calamagrostis epigeios community, Calamagrostis epigeios-Phragmites communis community, Phragmites communis-Ischaemum aristatum community, Phragmites communis community, Scirpus planiculmis community and Suaeda glauca-S. japonica community.These plant communities represents sand dune vegetation and salt marsh vegetation. Widely distributing types in the actual vegetation map were sea club-rush community, reed community in salt marsh, and dry grassland. The edge in the coastal sand bars has zonation that almost distribution by the reed community in salt marsh. But outside of it were distributed sea club-rush community. Dry grassland type distributes higher zone of the center in coastal sand bars. Respectively, the coastal sand dune and salt marsh vegetation types were distributed ocean and inland on the frontier of it.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.6
• /
• pp.528-535
• /
• 2004

Ultrasonic Vibrator is designed to achieve the maximum vibration amplitude at 30 kHz by in-cluding a horn (diameter, 40 mm), mechanical vibration amplifier at the top of the ultrasonic vibrator in the system and making the complete system resonate. In addition, it is experimentally visualized by particle imaging velocimetry (PIV) that the acoustic streaming velocity in the gap is at maximum when the gap between the ultrasonic vibrator and stationary plate agrees with the multiples of half-wavelength of the ultrasonic wave. This fact results from the resonance of the sound wave and the theoretical analysis of that is also accomplished and verified by experiment. It is observed that the magnitude of the acoustic streaming dependent upon the gap between the ultrasonic vibrator and stationary plate possibly changes due to the measurement of the average velocity fields of the acoustic streaming induced by the ultrasonic vibration at resonance and non-resonance. There exists extremely small average velocity at non-resonant gaps while the relatively large average velocity exists at resonant gaps compared with non-resonant gaps. It also reveals that there should be larger axial turbulent intensity at the hub region of the vibrator and at the edge of it in the resonant gap where the air streaming velocity is maximized and the flow phenomena is conspicuous than that at the other region. Because the variation of the acoustic streaming velocity at resonant gap is more distinctive than that at non-resonant gap, shear stress increases more in the resonant gap and is also maximized at the center region of the vibrator except the local position of center (r〓0). At the non-resonant gap there should be low values of vorticity distribution, but in contrast to the non-resonant gap, high and negative values of it exist at the center region of the vibrator with respect to the radial direction and in the vicinity of the middle region with respect to the axial direction. Acoustic streaming is noise-free due to the ultrasonic vibration and maintenance-free because of the absence of moving parts. Moreover, the proposed method by acoustic streaming can be utilized to the nano and micro-electro mechanical systems as a driving mechanism in addition to the augmentation of the streaming velocity.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.4
• /
• pp.55-62
• /
• 2007

This paper proposes a defective pixel detection algorithm and its hardware structure for CCD/CMOS image sensor. In previous algorithms, the characteristics of image have not been considered. Also, some algorithms need quite a time to detect defective pixels. In order to make up for those disadvantages, the proposed defective pixel detection method detects defective pixels efficiently by considering the edges in the image and verifies them using several frames while checking scene-changes. Whenever scene-change is occurred, potentially defective pixels are checked and confirmed whether it is defective or not. Test results showed that the correct detection rate in a frame was increased 6% and the defective pixel verification time was decreased 60%. The proposed algorithm was implemented with verilog HDL. The edge indicator in color interpolation block was reused. Total logic gate count was 5.4k using 0.25um CMOS standard cell library.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.1
• /
• pp.17-25
• /
• 2007

In most electronic imaging applications, image with high resolution(HR) are desired. HR means that pixel density within an image is high, and therefore HR image can offer more details that may be critical in various applications. Digital images that are captured by CCD and CMOS cameras usually have a very low resolution, which significantly limits the performance of image recognition systems. Image super-resolution techniques can be applied to overcome the limits of these imaging systems. Super-resolution techniques have been proposed to increase the resolution by combining information from multiple images. To techniques were consisted of the registration algorithm for estimation and shift, the nearest neighbor interpolation using weight of acquired frames and presented frames. In this paper, it is proposed the image interpolation techniques using the wavelet base function. This is applied to embody a correct edge image and natural image when expend part of the still image by applying the wavelet base function coefficient to the conventional Super-Resolution interpolation method. And the proposal algorithm in this paper is confirmed to improve the image applying the nearest neighbor interpolation algorithm, bilinear interpolation algorithm.,bicubic interpolation algorithm through the computer simulation.

• Journal of Radiation Protection and Research
• /
• v.45 no.3
• /
• pp.117-129
• /
• 2020

Background: Radiation portal monitors (RPMs) involving plastic scintillators installed at the border inspection sites can detect illicit trafficking of radioactive sources in cargo containers within seconds. However, RPMs may generate false alarms because of the naturally occurring radioactive materials. To manage these false alarms, we previously suggested an energy-weighted algorithm that emphasizes the Compton-edge area as an outstanding peak. This study intends to evaluate the identification of radioactive sources using an improved energy-weighted algorithm. Materials and Methods: The algorithm was modified by increasing the energy weighting factor, and different peak combinations of the energy-weighted spectra were tested for source identification. A commercialized RPM system was used to measure the energy-weighted spectra. The RPM comprised two large plastic scintillators with dimensions of 174 × 29 × 7 ㎤ facing each other at a distance of 4.6 m. In addition, the in-house-fabricated signal processing boards were connected to collect the signal converted into a spectrum. Further, the spectra from eight radioactive sources, including special nuclear materials (SNMs), which were set in motion using a linear motion system (LMS) and a cargo truck, were estimated to identify the source identification rate. Results and Discussion: Each energy-weighted spectrum exhibited a specific peak location, although high statistical fluctuation errors could be observed in the spectrum with the increasing source speed. In particular, ¹³⁷Cs and ⁶⁰Co in motion were identified completely (100%) at speeds of 5 and 10 km/hr. Further, SNMs, which trigger the RPM alarm, were identified approximately 80% of the time at both the aforementioned speeds. Conclusion: Using the modified energy-weighted algorithm, several characteristics of the energy weighted spectra could be observed when the used sources were in motion and when the geometric efficiency was low. In particular, the discrimination between ⁶⁰Co and ⁴⁰K, which triggers false alarms at the primary inspection sites, can be improved using the proposed algorithm.

• Culinary science and hospitality research
• /
• v.19 no.2
• /
• pp.130-148
• /
• 2013

Domestic pizza market in Korea is in the age of maturity, and competition in the market is getting intense. Brand personality that can prompt consumer sensibility is evaluated as a proper method to differentiate the image of a corporate rather than products or technology that can be copied easily by competitors. In this study, we examined the structural relationships among brand personality of pizza brands in Korea, customer-brand relationship quality, and repurchase intention with selected measurement based on Aaker's Big 5. Based on questionnaires answered by 291 customers, this study examined validity and reliability by using SPSS 16.0 and AMOS 5.0 for its hypotheses. The result of the study modelling were GFI=0.900, NFI=0.922, CFI=0.965, RMSEA=0.050 at the level of ${\chi}^2$=384.130(df=1.715, p<0.001). First, sincerity, competence, and sophistication of the pizza brand personality had a positive effect on intimacy. Second, sincerity, competence, sophistication, and strength of the pizza brand personality had a positive effect on brand partner quality. Also, intimacy and brand partner quality had a positive effect on repurchase intention. Therefore, in the practical perspective, pizza brand management can utilize the findings of specific pizza brand personality in creating a competitive edge for marketing.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.20
• /
• pp.8651-8656
• /
• 2014

Purpose: To study the expression of angiogenin-2 (Ang-2) and its receptor Tie-2 in colorectal cancer and discuss the possible mechanisms behind this process. Materials and Methods: Using the streptavidin-peroxidase (SP) immunohistochemical method, paraffin sections from 100 colorectal cancer samples and 10 samples from tumor-adjacent normal tissue (> 2 cm from the edge of the gross tumor) were tested for protein expression of Ang-2, Tie-2, PI3K, and AKT. Reverse transcription-polymerase chain reaction and Western blots were further used to measure expression of the 4 genes and proteins in 20 freshly-resected colorectal cancer samples and tumor-adjacent normal tissues. Results: In colorectal cancer tissues, the expression of the Ang-2, Tie-2, PI3K, and AKT genes and their proteins was significantly higher than in tumor-adjacent normal tissues. Protein expression in poorly-differentiated adenocarcinoma was higher than that in well and moderately differentiated adenocarcinoma. According to Duke's classification, the protein expression in Stages C and D was significantly higher than that in Stages A and B. In the group with lymphatic metastasis, the protein expression was higher than that without lymphatic metastasis. Conclusions: In colorectal cancer, the expression of the Ang-2, Tie-2, PI3K, and AKT genes and their proteins is markedly higher than those in tumor-adjacent normal tissues. No correlation was observed between protein expression and gender, location, or histologic type. Correlations did exist between protein expression and differentiation level, stage of Duke's classification, and lymphatic metastasis; in colorectal cancer tissues with lower differentiation levels, higher stages of Duke's classification, and lymphatic metastasis, the expression of all 4 proteins was higher. The study of their expression patterns and relationships with aggression and metastasis will provide a valuable experimental foundation for assessing prognosis and targeted therapy of colorectal cancer.