• Composites Research
• /
• 제36권4호
• /
• pp.259-263
• /
• 2023

This study investigated the open hole tensile (OHT) properties of carbon fiber/epoxy composites and compared them to bolt joint tensile (BJT) properties. The net nominal modulus and strength (1376 MPa) were found to be higher than the gross nominal strength (1041 MPa), likely due to increasing hole size. The OHT and BJT specimens exhibited similar stiffness, as expected without bolt rotation causing secondary bending. OHT specimens experienced a sharp drop in stress indicating unstable crack propagation, delamination, and catastrophic failure. BJT specimens failed through shear out on the bolt side and bearing failure on the nut side, involving fiber kinking, matrix splitting, and delamination, resulting in lower strength compared to OHT specimens. The strength retention of carbon fiber/epoxy composites with open holes was 66%. Delamination initiation at the hole's edge caused a reduction in the stress concentration factor. Filling the hole with a bolt suppressed this relieving mechanism, leading to lower strength in BJT specimens compared to OHT specimens. Bolt joint efficiency was calculated as 15%. The reduction in strength in bolted joints was attributed to fiber-matrix splitting and delamination, aligning with Hart Smith's bolted joint efficiency diagram. These findings contribute to materials selection and structural reliability estimation for carbon fiber/epoxy composites. They highlight the behavior of open hole and bolt joint configurations under tensile loading, providing valuable insights for engineering applications.

• 한국통신학회논문지
• /
• 제38A권12호
• /
• pp.1125-1134
• /
• 2013

최근 많은 수의 모바일 유저와 과도한 트래픽 증가를 해결하기 위한 솔루션으로 피코 혹은 펨토 셀과 같은 소형 셀을 설치하는 방법이 주목 받고 있다. 그러나 소형 셀에 속한 엣지 유저들은 주변 기지국으로부터 극심한 셀간 간섭을 받기 때문에 낮은 평균 전송률을 얻게 되고, 이를 해결하기 위해서는 셀 간 간섭을 효과적으로 관리하는 방법이 필요하다. 최근의 많은 연구들은 셀 간 간섭 관리를 위해 기지국의 전송 전력을 제어하는 알고리즘을 제시하였지만, 제시된 방법들은 높은 복잡도를 가지고 중앙 기지국의 도움을 필요로 한다는 단점이 있다. 본 연구에서는 기지국간의 경쟁을 기반으로 하여, 낮은 복잡도를 가지는 분산화된 방법의 기지국 전송 전력 on/off 제어 및 유저 스케줄링 알고리즘을 제안한다. 시뮬레이션 결과를 통해, 제안하는 방법이 셀 간 간섭 관리를 하지 않는 방법에 비해 셀 엣지 유저의 경우 170%의 성능 개선을 보이고, 최적의 알고리즘과 비교 했을 때 88-96%에 달하는 geometric average throughput (GAT) 성능 및 매우 근접한 average edge user throughput (AET) 성능을 보임을 검증한다.

• 정보처리학회논문지:컴퓨터 및 통신 시스템
• /
• 제12권2호
• /
• pp.47-52
• /
• 2023

최근 스마트 디바이스 및 스트리밍 서비스의 수요 증가에 따른 네트워크 트래픽을 효과적으로 관리하기 위한 방법으로 Mobile Edge Computing(MEC)기술이 주목받고 있다. MEC는 Base Station(BS)과 같은 네트워크 엣지에 캐시를 설치함으로써 사용자에게 보다 가까운 곳에서 서비스를 제공하므로 낮은 지연시간을 제공하고, 네트워크 부하를 감소시킬 수 있다. 또한, 엣지 네트워크에서 사용자는 가장 가까운 BS와 연결되는 것보다 요청된 콘텐츠가 캐싱되어 있는 BS와 연결하는 것이 서비스 지연시간 감소에 유리하다. 따라서 본 논문에서는 캐시 적중률 향상을 위한 이동성 기반 캐싱 및 사용자 연결(user association)알고리즘을 제안한다. 제안 알고리즘은 체류시간과 콘텐츠 요청 유사도를 토대로 사용자 연결을 결정하고 콘텐츠를 캐싱한다. 시뮬레이션을 통해 기존 연구 대비 제안 알고리즘의 향상된 캐시 적중률과 감소된 지연시간을 확인한다.

• 대한의용생체공학회:의공학회지
• /
• 제28권3호
• /
• pp.332-337
• /
• 2007

In the early twenty-first century, minimally invasive surgery is the mainstay of various kinds of surgical fields. Surgeons gave percutaneously surgical treatment of the screw directly using a fluoroscopic view in the past. The latest date, they began to operate the fractured carpal bone surgery using Computerized Tomography (CT). Carpal bones composed of wrist joint consist of eight small bones which have hexahedron and sponge shape. Because of these shape, it is difficult to grasp the shape of carpal bones using only CT image data. Although several image segmentation studies have been conducted with carpal bone CT image data, more studies about carpal bone using CT data are still required. Especially, to apply the software implemented from the studies to clinical fIeld, the outcomes should be user friendly and very accurate. To satisfy those conditions, we propose modified multi-seed region growing segmentation method which uses simple threshold and the canny edge detector for finding edge information more accurately. This method is able to use very easily and gives us high accuracy and high speed for extracting the edge information of carpal bones. Especially, using multi-seed points, multi-bone objects of the carpal bone are extracted simultaneously.

• Journal of Welding and Joining
• /
• 제17권2호
• /
• pp.66-75
• /
• 1999

Weld bead quality in tailored blank(TB) is critically affected by edge preparation of sheets. The edge quality of prepared sheets for TB can be classified into straightness and the cross section quality of sheared plane such as a ratio of shear face, shear plane angle, etc. In order to have a good edg quality for butt-welding sheets, precision shearing will be recommended. In this paper, the feasibility of a conventional mechanical shearing as the edge preparation for tailored blanks is studyied. It reveals that fine shearing may not be the unique solution as it is generally accepted. To obtain the good shearing condition with a conventional mechanical shearing, experiments were carried out using Tahuchi method. The major parameters affecting a sheared contour are the clearance between upper blade and lower blade, and shear angle. The optimal shearing condition yields a very good straightness along the entire length of the cut, which gives a butt joint gap less than 10% of the base material thickness. The good cross section of sheared plane is also achieved in the optimal shearing condition such as a ratio of the shear face above 65%, a cross section's shear plane angle above 85%, little burr, which is providing finally good weld beads.

• Journal of Oral Medicine and Pain
• /
• 제23권4호
• /
• pp.369-377
• /
• 1998

A patient with TMJ osteoarthritis and anterior open bite was treated with an intermaxillary traction device. Pretreatment examination revelaed a pain in both TMJ during mouth opening, moderate tendernesso f left sternocleidomastoid and right trapezius muscles. Anterior open Bite was aobserved with interincisal distance of 2mm. Tomograms and MRI showed anterior disc displacement withouit reductoin of both temporomandibular joints, and the condyles were flattened and slightly eroded. A pair of full-coverage occlusal appliances was made on both maxillary and mandibular dentition, with pivoting fulcrum on the site of the second moalr. Traction force was gained by the intermaxillary orthodontic elastics which were hooked by orthodontic brackets on the labial surfaces of the upper and lower anterior and premolar teeth. After 8 weeks of traction treatment, the joint pain was subsided completely and the anterior open bite was closed to get an edge to edge relationship of anterior teeth.

• 한국가구학회지
• /
• 제18권1호
• /
• pp.20-30
• /
• 2007

This experiment was carried out to investigate the effects of number and location of finger joints on the bending strength of glue-laminated lumbers. Urea resin adhesives were used in this experiment and the resin content was 70% for cold pressing. The lamina were edge-jointed and end-jointed. The specimen were composed of one or three layers. The obtained results are summarized as follows; The effects of finger joints on the decrease of bending strength of glue laminated woods were different according to the number and location of finger joints. The decrease of MOR was highest on the middle position of laminated woods. The effects of several arrangements of finger joints on the bending strength of glue laminated woods showed on Figure 7 and 8. The variance of thickness-laminating on the bending strength of glue laminated woods were larger than those of width-laminating.

• 한국경영과학회지
• /
• 제14권1호
• /
• pp.88-96
• /
• 1989

General measure in the reliability is the k-terminal reliability, which is the probability that the specified vertices are connected by the working edges. To compute the k-terminal reliability components are usually assumed to be statistically independent. In this study the modeling and analysis of the k-terminal reliability are investigated when dependency among components is considered. As the size of the network increases, the number of the joint probability parameter to represent the dependency among components is increasing exponentially. To avoid such a difficulty the structured-event-based-reliability model (SERM) is presented. This model uses the combination of the network topology (physical representation) and reliability block diagram (logical representation). This enables us to represent the dependency among components in a network form. Computational algorithms for the k-terminal reliability in SERM are based on the factoring algorithm Two features of the ractoring algorithm are the reliability preserving reduction and the privoting edge selection strategy. The pivoting edge selction strategy is modified by two different ways to tackle the replicated edges occuring in SERM. Two algorithms are presented according to each modified pivoting strategy and illustrated by numerical example.

• 대한치과의사협회지
• /
• 제22권10호통권185호
• /
• pp.869-877
• /
• 1984

An objective examination of 123 subjects aged from 19 to 23 was made from a clinical standpoints to determine the natural occurrence in anterior tooth contact in centric occlusion, and tooth contact in protrusive occlusion, left and right lateral excursions, and temporomandibular dysfunction. 1. In centric occlusion, maxillary 6 anterior contact type was frequently observe (30.08%) compared with other types of contact (incisor contact: 19.47%, no contact: 17.70%, canine and incisor contact: 15.04%, canines contact: 12.39%, unilateral canine contact: 5.31%) (P<0.01) 2. In protrusive position (edge to edge bite), maxillary central incisors contact was predominant (86.7%). (P<0.01) 3. In lateral excursion, there was not any significant difference between canine guided occlusion (47.79%) and group function occlusion (total 51.32%, AG:9.29%, PG:13.27%, G:28.76%). 4. Temporomandibular joint dysfunction was observed in 12.4% of 123 subjects.

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3058-3067
• /
• 1996

With increasing use of ceramics/metal bonded joints, It is required to analyze the residual stress distribution and stress singularity at an interface edge for its bonded joints. In this paper, the residual stress distribution and stress singularity index of the ceramics/metal bonded joints were analyzed by using 2-dimensional elastic boundary element method. The variations of residual stress distribution and stress singularity index are studied with changes for the combinations of ceramics/metal bodned joints.