• 환경위생공학
• /
• 제3권2호
• /
• pp.43-60
• /
• 1988

This study was carried out to determine traffic noise level and analyze noise reduction effects of various sound protection facilities in the area of Seoul, Inch'on, Songchoo and Seoul- Busan Expressway from March to Octover, 1987. The results were as follows; 1. As compared with the environmental standards and the traffic noise level in heavy noise areas, traffic noise levels observed were shown in higher than environmental standards. The noise levels in Seoul were determined at 12.8-18.2 dB(A) in daytime and 19.0-26.9 dB (A) in nighttime. And incase of inch'on, it were 6.7-9.6 dB(A) in daytime, 7.9-18.9 dB(A) in nighttime, respectively. 2. The environmental noise level observed in the backside of protection facilities, such as apartment, soundproof barrier and houses, which were constructed in paralled to the road was lower about 3-5 dB(A) than perpendicular to theroad. Noise recuction effect of upper stairs in apartment was higher than lower stairs. 3. The predicted noise level obtained from the equation $({\triangle}L\;=\; -10\;log\;(^{I'1}/Ii)\;was\;\pm\;1dB$ (A) and the correlation coefficient (r) was 0.923. 4. The noise reduction effect in backside of apartment was measured at on sites and predicted by total noise loss equation. The predicted noise level was 60.9 dB(A) and the measured level was 60.6 dB(A), respectively. 5. The narrow width landscape less than 10m width was almost no effect for the protection of traffic noise. According to the synthesis of the above results, the noise level of the road was exceeding mostly the environmental standard in the heavy traffic areas. The counterplan should be set as well. The insulation of noise protection facilities were effective by the location with near distance from the road edge. The reduction effect of double window in apartment was represented so much. The prediction model could be applied to estimate the noise levels in the roadside as well as the effectiveness for the noise protection facilities.

• Tribology and Lubricants
• /
• 제33권3호
• /
• pp.119-125
• /
• 2017

In this study, we perform a numerical analysis to predict the film thickness and lubrication regions for a thrust ball bearing under different operating conditions. Film thinning and replenishment affect the film thickness in starved lubrication. As the inlet meniscus position is brought to the edge of the Hertz contact, the thin film thickness is calculated as starved equation. We use a film replenishment model to determine the recovery film thickness between rolling elements. We use a hydrodynamic model to describe film recovery, that results from the effects of surface tension. In this model, we consider the surface tension gradient in fluid depression as the driving force for fluid recovery. We use Fourier transform method to determine the time-dependent depth of depressed oil. We calculate the change in the central film thickness graphically by using the recovery equation in starved elastohydrodynamic lubrication(EHL) under operating conditions that include numbers of balls, sliding velocity, applied force, and ambient film thickness. We evaluate the degree of starvation by using the distance from the center of the contact area to the meniscus position. Parched lubrication, a phenomenon where the film thickness decreases consistently, occurs at the severe condition. We determine optimal values with respect to the numbers of balls, and sliding velocity. The investigation can contribute to the design operating conditions for proper lubrication.

• 한국정보통신학회논문지
• /
• 제2권4호
• /
• pp.643-652
• /
• 1998

이동통신용 중계안테나는 현재 약 -20 dB의 후방부엽이 존재한다. 이는 인접한 안테나에 전파감쇠 및 장애를 일으키고 있어 후방부엽을 억제시키는 것이 절실히 요구되고 있다. 본 논문에서는 기존의 Back Plate 구조를 새롭게 변형하여 후방부엽의 발생을 억압시키고, -30 dB이하의 Null Point의 각도를 넓히고자 한다. 새로운 구조의 Back Plate는 리플렉터안테나의 원리를 이용하여 ㄷ자 형태로 만들었다. Back Plate구조의 설계를 위해 범용 소프트웨어 툴인 NEC Win Pro를 사용하였다. 각 파라미터에 대한 계산으로부터 $\pm180^\circ$에서 -48.48 dB 의 후방부엽을 갖는 중계국안테나를 설계하였으며, 또한 다이폴의 길이, 다이폴 사이의 간격 및 Back Plate 크기 등의 조정으로부터 -30 dB이하에서 64$^{\circ}$의 Null Point 각도를 가지는 안테나를 설계하였다.

• 한국강구조학회 논문집
• /
• 제25권6호
• /
• pp.659-669
• /
• 2013

본 연구는 페라이트계 스테인리스강 일면전단 볼트접합부의 구조거동에 관한 기존실험연구를 바탕으로 유한요소해석법을 이용하여 접합부의 최대내력과 면외변형에 대해 조사하는 것을 목적으로 한다. 유한요소해석결과와 실험결과의 비교를 통해 접합부의 구조거동을 예측하는데 있어 해석의 타당성을 검증하였다. 면외변형에 의해 유발되는 접합부의 연단거리 조건을 조사하고 최대내력저하정도를 정량적으로 평가하였다. 또한, 변수해석을 통해 얻어진 해석결과의 최대내력과 현행기준식인 AISC, KBC2009, AIJ 및 AISI에 의해 예측된 내력과 비교하여 그 적용성을 검토하였다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제22권3호
• /
• pp.42-49
• /
• 2017

TOUGH2 was used to simulate the migration of $CO_2$ injected into a sandy aquifer. A series of numerical simulations was performed to investigate the effects of a low-permeability layer (LPL) embedded in the aquifer on the injection rate and the pressure distribution of $CO_2$. The results show that the size and location of the LPL greatly affected the spread of $CO_2$. The pressure difference between two points in the aquifer, one each below and above the LPL, increased as the size of the LPL increased, showing a critical value at 200 m, above which the size effect was diminished. The location of the LPL with respect to the injection well also affected the migration of $CO_2$. When the injection well was at the center of the LPL, the injection rate of $CO_2$ decreased by 5.0% compared to the case with no LPL. However, when the injection well was at the edge of the LPL, the injection rate was decreased by only 1.6%. The vertical distance between the injection point and the LPL also affected the injection rate. The closer the LPL was to the injection point, the lower the injection rate was, by up to 8.3%. Conclusively, in planning geologic storage of $CO_2$, the optimal location of the injection well should be determined considering the distribution of the LPL in the aquifer.

• Steel and Composite Structures
• /
• 제15권6호
• /
• pp.585-603
• /
• 2013

Generally the required strength and stiffness of an I-shaped beam to the box-shaped column connection is achieved if continuity plates are welded to the column flanges from all sides. However, welding the forth edge of a continuity plate to the column flange may not be easily done and is normally accompanied by remarkable difficulties. This study was aimed to propose an alternative for box columns with continuity plates to diminish such problems. For this purpose a double-web I-shaped column was proposed. In this case the strength and rotational stiffness of the connection was provided by nearing the column webs to each other. Finite element studies on about 120 beam-column connections showed that the optimum proportion of the distance between two column webs and the width of the column flange (parameter ${\beta}$) was a function of the ratio of the beam flange width to the column flange width (parameter ${\alpha}$). Hence, based on the finite element results, an equation was proposed to estimate the optimum value of parameter ${\beta}$ in terms of parameter ${\alpha}$ to achieve the highest connection performance. Results also showed that the strength and ductility of post-Northridge connections of such columns are in average 12.5 % and 54% respectively higher than those of box-shaped columns with ordinary continuity plates. Therefore, a double-web I-shaped column of optimum arrangement might be a proper replacement for a box column with continuity plates when beams are rigidly attached to it.

• Earthquakes and Structures
• /
• 제8권5호
• /
• pp.1039-1054
• /
• 2015

The purpose of this study was to evaluate the seismic performance of weak-axis column-tree type connections used in steel moment frames. These connections are composed of a shop-welded and fieldbolted steel structure and can improve welding quality. On this basis, column-tree type connections are widely used in steel moment resisting frames in Korea and Japan. In this study, splices designed with a semirigid concept regarding the seismic performance of column-tree connections were experimentally evaluated. The structures can absorb energy in an inelastic state rather than the elastic state of the structures by the capacity design method. For this reason, the plastic hinge might be located at the splice connection at the weak-axis column-tree connection by reducing the splice plate thickness. The main variable was the distance from the edge of the column flange to the beam splice. CTY series specimens having column-tree connections with splice length of 600 mm and 900 mm were designed, respectively. For comparison with two specimens with the main variable, a base specimen with a weak-axis column-tree connection was fabricated and tested. The test results of three full-scale test specimens showed that the CTY series specimens successfully developed ductile behavior without brittle fracture until 5% story drift ratio. Although the base specimen reached a 5% story drift ratio, brittle fracture was detected at the backing bar near the beam-to-column connection. Comparing the energy dissipation capacity for each specimen, the CTY series specimens dissipated more energy than the base specimen.

• 한국콘텐츠학회논문지
• /
• 제10권10호
• /
• pp.1-8
• /
• 2010

현재 카메라로 입력된 문자 영상 처리를 위한 기술 개발이 국내외에서 활발히 이루어지고 있으나 낮은 정확도나 처리시간이 많이 걸리는 문제점 등으로 실용화 비율은 현저히 낮다. 본 논문에서는 휴대단말기 카메라에서 얻은 영상으로 기하학적 정보를 이용한 차량 번호판 인식 방법을 제안한다. 휴대폰 영상의 낮은 해상도와 부족한 명암대비, 각도 차이 등을 고려한 전처리 작업 수행 후 투영에지 누적 계산을 통해 추출된 번호판 영역에서 체인코드와 Thickness 정보를 이용하여 문자를 인식한다. 제안된 알고리즘은 기존의 차량 번호판 인식 알고리즘의 문제점과 휴대단말기 영상 처리라는 점 등을 고려하여 가볍고 처리 시간을 단축시켰으며, 실험 결과 95%의 문자 인식 성공률을 얻었다. 향후 연구로 원거리 영상이나 모션블러가 가미된 영상에서의 번호판 인식 알고리즘을 모색할 예정이다.

• 한국정보과학회논문지:소프트웨어및응용
• /
• 제37권1호
• /
• pp.80-84
• /
• 2010

손 추적 기술은 인간과 기계와의 효율적인 의사소통을 위한 손동작 인식 기술의 핵심 기반 기술이다. 최근의 손 추적 연구는 3차원 손 모델을 이용한 연구 방향에 초점을 맞추고 있고, 기존의 2차원 손 모델을 이용한 방법보다 강인한 추적 성능을 보이고 있다. 본 논문에서는 결합된 파티클 필터에 기반한 새로운 3차원 손 추적 방법을 제안한다. 이는 전역적 손 형상과 지역적 손가락 움직임을 분리하여 추정하고, 각각의 추정 결과를 서로의 사전 정보로 이용하여 기존의 방법보다 빠르고 강인한 추적을 가능하게 한다. 또한, 추적 성능 향상을 위해 색상과 에지를 함께 고려한 다중 증거 결합 방법을 적용한다. 실험결과, 제안하는 방법은 복잡한 배경이나 동작에서도 강인한 추적 결과를 보였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 1999년도 춘계종합학술대회
• /
• pp.50-54
• /
• 1999

본 논문에서는 영상의 다양한 특징 정보 중에서 색상 특징과 모양 특징을 이용한 영상 검색 시스템을 제안한다. 색상 특징은 지역별 색상 분포 히스토그램을 추출하고, 각 지역의 히스토그램 중에 가장 큰 값을 가지는 4개의 값을 특징 정보로 이용한다. 모양 특징을 추출하기 위한 전처리 과정은 경계면 추출과정, 경계면에 대한 무게 중심 추출 과정, angular sampling 과정으로 구성되고, 무게 중심으로부터 경계면까지의 거리의 합, 표준 편차, 장축/단축 비율을 특징 정보로 이용한다. 각 질의 영상들의 특징 정보와 데이터베이스에 저장된 영상들의 특징 정보들 비교하여 유사도 순위에 따라 후보영상들이 검색된다. 200개의 폐곡선을 이루는 상표영상에 대한 검색 실험을 통하여 색상 정보와 모양 정보에 대한 정확도를 측정하였다. 실험 결과 평균 Recall/Precision이 0.72/0.83를 보임으로써 제안된 방법이 유용함을 보였다.