• Economic and Environmental Geology
• /
• v.35 no.3
• /
• pp.257-271
• /
• 2002

One of the main interests in relation to heavily contaminated gully-pot sediment in urban area is the short term mobility of heavy metals, which depends on the pH of acidic rainwater and on the buffering effects of carbonate minerals. The buffering effects of carbonates are determined by titration (acid addition). Leaching experiments are carried out in solutions with variable initial HN03 contents for 24h. The gully-pot sediment appears to be predominantly buffered by calcite and dolomite. In case of sediment samples, which highly contain carbonates, pH decreases more slowly with increasing acidity. On the other hand, for the sediment samples, which less contain carbonate minerals, pH rapidly drops until it reaches about 2 then it decreases slowly. The leaching reactions are delayed until more acid is added to compensate for the buffering effects of carbonates. The Zn, Cu, Pb and Mn concentrations of leachate rapidly increase with decreased pH, while Cd, Co, Ni, Cr and Fe dissolutions are very slow and limited. The solubility of heavy metals depends not only on thc pH values of leachatc but also on the speciation in which metals are associated with sediment particles. In slightly to moderately acid conditions, Zn, Cd, Co, Ni and Cu dissolutions become increasingly important. As deduced from leaching runs, the relative mobility of heavy metals at pH of 5 is found to be: Zn > Cd > Co > Ni > Cu » Pb > Cr, suggesting that moderately acid rainwater leach Zn, Cd, Co, Ni and Cu from thc contaminated gully-pot sediment, while Pb and Cr would remain fixed. The buffering effects of Ca- and Mg-carbonates play an important role in delaying as well as limiting the leaching reactions of heavy metals from highly contaminated gully-pot sediment. The extent of such a secondary environmental pollution will thus depends on how well the metals in sediment can be leached by somewhat acidic rain water. Changes in the physicochemical environments may result in the severe environmental pollution of heavy metals. These results are to be taken into account in the management of contaminated sediments during rainstorms.

• Economic and Environmental Geology
• /
• v.43 no.6
• /
• pp.555-564
• /
• 2010

Remediation process by using the bio-carrier (beads) with dead Bacillus sp. B1 and polysulfone was investigated for heavy metal contaminated groundwater. Sorption batch experiments using the bio-carrier were performed to quantify the heavy metal removal efficiencies from the contaminated solution. The analyses using SEM/EDS and TEM for the structure and the characteristic of precipitates on/inside the beads were also conducted to understand the sorption mechanism by the bio-carrier. Various amounts of freeze-dried dead Bacillus sp. B1 were mixed with polysulfone + DMF(N,N-dimethylformamide) solution to produce the bio-carrier (beads; less than 2mm in diameter) and 5% of Bacillus sp. B1 in the bio-carrier was optimal for Pb removal in the solution. The removal efficiency ratings of the bio-carrier for Pb, Cu and Cd were greater than 80% after adding 2g of bio-carrier in 50ml of aqueous solution (<10mg/L of each heavy metal concentration). Reaction time of the bio-carrier was very fast and most of the sorption reaction for heavy metals were completed within few hours. Batch experiments were duplicated at various pH conditions of aqueous solutions and Cu and Pb removal efficiencies highly maintained at wide pH ranges (pH 2-12), suggesting that the bio-carrier can be useful to clean up the acidic waste water such as AMD. From SEM/EDS and TEM analyses, it was observed that the bio-carrier was spherical shape and was overlapped by many porous layers. During the sorption experiment, Pb was crystallized on the surface of porous layers and also was mainly concentrated at the boundary of Bacillus sp. B1 stroma and polysulfone substrate, showing that the main mechanism of the bio-carrier to remove heavy metals is the sorption on/inside of the bio-carriers and the bio-carriers are excellent biosorbents for the removal of heavy metal ions from groundwater.

• Economic and Environmental Geology
• /
• v.42 no.5
• /
• pp.403-412
• /
• 2009

The objective of this study is to investigate the geochemical change of feldspar minerals by supercritical $CO_2$, which exists at $CO_2$ sequestration sites. High pressurized cell system (100 bar and $50^{\circ}C$) was designed to create supercritical $CO_2$ in the cell and the surface change and the dissolution of plagioclase and orthoclase were observed when the mineral surface reacted with supercritical $CO_2$ and water (or without water) for 30 days. The polished slab surface of feldspar was contacted with supercritical $CO_2$ and an artificial brine water (pH 8) in the experiments. The experiments for the reaction of feldspar with only supercritical $CO_2$ (without brine water) were also conducted. Results from the first experiment showed that the average roughness value of the plagioclase surface was 0.118 nm before the reaction, but it considerably increased to 2.493 nm after 30 days. For the orthoclase, the average roughness increased from 0.246 nm to 1.916 nm, suggesting that the dissolution of feldspar occurs in active when the feldspars contact with supercritical $CO_2$ and brine water at $CO_2$ sequestration site. The dissolution of $Ca^{2+}$ and $Na^+$ from the plagioclase occurred and a certain part of them precipitated inside of the high pressurized cell as the form of amorphous silicate mineral. For the orthoclase, $Al^{3+}$, $K^+$, and $Si^{+4}$ were dissolved in order and the kaolinite was precipitated. In the experiments without water, the change of the average roughness value and the dissolution of feldspar scarcely occurred, suggesting that the geochemical reaction of feldspars contacted with supercritical $CO_2$ at the environment without the brine water is not active.

• The Journal of Art Theory & Practice
• /
• no.5
• /
• pp.217-229
• /
• 2007

Many historical research and facet about modern art in Indonesia which formulating background of contemporary Indonesian Art. Indonesian art critic Sanento Yuliman states that Modern art has been rapidly developing in Indonesia since the Indonesian Independence in 1945. Modern Art is a part of the super culture of the Indonesian metropolitan and is closely related to the contact between the Indonesian and Western Cultures. Its birth was part of the nationalism project, when the Indonesian people consists of various ethnics were determined to become a new nation, the Indonesian nation, and they wished for a new culture, and therefore, a new art. The period 1960s, which was the beginning of the creation and development of the painters and the painters associations, was the first stage of the development of modern art in Indonesia. The second stage showed the important role of the higher education institutes for art. These institutes have developed since the 1950s and in the 1970s they were the main education institutes for painters and other artists. The artists awareness of the medium, forms or the organization of shapes were encouraged more intensely and these encouraged the exploring and experimental attitudes. Meanwhile, the information about the world's modern art, particularly Western Art; was widely and rapidly spread. The 1960s and 1970s were marked by the development of various abstractions and abstract art and the great number of explorations in various new media, like the experiment with collage, assemblage, mixed media. The works of the Neo Art Movement-group in the second half of the 1970s and in the 1980s shows environmental art and installations, influenced by the elements of popular art, from the commercial world and mass media, as well as the involvement of art in the social and environmental affairs. The issues about the environment, frequently launched by the intellectuals in the period of economic development starting in the 1970s, echoed among the artists, and they were widened in the social, art and cultural circles. The Indonesian economic development following the important change in the 1970s has caused a change in the life of the middle and upper class society, as has the change in various aspects of a big city, particularly Jakarta. The new genre emerged in 1975 which indicates contemporary art in Indonesia, when a group of young artists organized a movement, which was widely known as the Indonesian New Art Movement. This movement criticized international style, universalism and the long standing debate on an east-west-dichotomy. As far as the actual practice of the arts was concerned the movement criticized the domination of the art of painting and saw this as a sign of stagnation in Indonesian art development. Based on this criticism 'the movement' introduced ready-mades and installations (Jim Supangkat). Takes almost two decades that the New Art Movement activists were establishing Indonesian Installation art genre as contemporary paradigm and influenced the 1980's gene ration like, FX Harsono, Dadang Christanto, Arahmaiani, Tisna Sanjaya, Diyanto, Andarmanik, entering the 1990's decade as "rebellion period" ; reject towards established aesthetic mainstream i.e. painting, sculpture, graphic art which are insufficient to express "new language" and artistic needs especially to mediate social politic and cultural situation. Installation Art which contains open possibilities of creation become a vehicle for aesthetic establishment rejection and social politics stagnant expression in 1990s. Installation art accommodates two major field; first, the rejection of aesthetic establishment has a consequences an artists quest for medium; deconstruction models and cross disciplines into multi and intermedia i.e. performance, music, video etc. Second aspect is artists' social politic intention for changes, both conclude as characteristics of Indonesian Installation Art and establishing the freedom of expression in contemporary Indonesian Art until today.

• Korean Journal of Organic Agriculture
• /
• v.29 no.2
• /
• pp.223-240
• /
• 2021

This study was carried out to investigate the economic value of organic wheat production using gelatin·chitin microorganisms in Gwangsan-gu, Gwangju city. The soil condition of experiment field was clay loam Jisan series. The organically cultivated fields were sprayed gelatin and chitin degrading bacteria. The test was performed at conventionally cultivated field and organically cultivated field. Emergence of weed on organically cultivated field was significantly higher than conventionally cultivated field which sprayed herbicide before seeding. Weed emergence have a critical impact on grain yield. Occurrence of diseases and insect pests were higher than conventionally cultivated fields. In 2019, the amount of lodging in conventionally cultivated field were higher than conventionally cultivated field. In 2020, lodging and wet injury were occur in both field. Comparing yield element between organically and conventionally cultivated experimental area, grain yield in organically cultivated field was shown slightly higher amount than conventionally cultivated field. However in the actual yield of 2019, organically cultivated field shows 20% deceased yield because of overgrown weed. In 2020, weed emergence and yellow mosaic virus by wet injury cause 30% decease in the grain yield in organically cultivated field. Content of protein, carbohydrates, ash, water and fat in the grain were not different significance. In 2019, net incomes of conventionally cultivated wheat was 461,031 won/0.1 ha while organically cultivated wheat was 443,437 won/0.1 ha. In the rate of income, conventionally cultivated field was 83.0% as against organically cultivated field (73.3%). In 2020, net incomes of organically cultivated wheat was 437,812 won/0.1 ha while conventionally cultivated wheat was 418,281 won/0.1 ha. In the rate of income, conventionally cultivated field was 81.6% as against organically cultivated field (73.0%).

• Economic and Environmental Geology
• /
• v.52 no.3
• /
• pp.223-230
• /
• 2019

The calcination of oyster shells have been studied as the possible substitute for the limestone used as an absorbent of $SO_2$ gas. However, since pure shells can not be used in calcination process, some impurities are contained and the changes in the characteristics of the calcination products are expected. In this study, the surface characteristics of the calcination products are investigated by mineralogical analysis according to the contents of NaCl, which can be derived from sea water, and sediments on the surface of the shell as impurities. The marine sediments on the shells were mainly composed of quartz, albite, calcite, small amounts of amphibole and clay minerals such as ilite, chlorite and smectite. After calcination of oyster shells mixed with 0.2-4.0 wt% sediments at $900^{\circ}C$ for 2 hours, regardless of the dehydration, dehydroxylation, and phase change of these minerals at the lower temperature than this experiment, no noticeable changes were observed on the specific surface area of the calcined product. However, when mixed with 0.1 to 2.0 wt% NaCl, the specific surface area generally increases as compared with the shell sample before calcination. The specific surface area increases with increasing amount of salt, and then decreases again. This is closely related to the changes of surface morphology. As the amount of NaCl increases, the morphology of the surface is similar to that of gel. It changes into a slightly angular, smaller particle and again looks like gel with increasing amount of NaCl. Our results show that NaCl affects morphological changes probably caused by melting of some oyster shells, but may have different effects on the specific surface area of calcination product depending on the NaCl contents.

• Economic and Environmental Geology
• /
• v.53 no.6
• /
• pp.667-675
• /
• 2020

An Alum-sludge based adsorbent (ASBA) was synthesized by the hydrothermal treatment of alum sludge obtained from settling basin in water treatment plant. ASBA was applied to remove fluoride and arsenic in artificially-contaminated aqueous solutions and mine drainage. The mineralogical crystal structure, composition, and specific surface area of ASBA were identified. The result revealed that ASBA has irregular pores and a specific surface area of 87.25 ㎡ g-1 on its surface, which is advantageous for quick and facile adsorption. The main mineral components of the adsorbent were found to be quartz(SiO2), montmorillonite((Al,Mg)2Si4O10(OH)2·4H2O) and albite(NaAlSi3O8). The effects of pH, reaction time, initial concentration, and temperature on removal of fluoride and arsenic were examined. The results of the experiments showed that, the adsorbed amount of fluoride and arsenic gradually decreased with increasing pH. Based on the results of kinetic and isotherm experiments, the maximum adsorption capacity of fluoride and arsenic were 7.6 and 5.6 mg g-1, respectively. Developed models of fluoride and arsenic were suitable for the Langmuir and Freundlich models. Moreover, As for fluoride and arsenic, the increase rate of adsorption concentration decreased after 8 and 12 hr, respectively, after the start of the reaction. Also, the thermodynamic data showed that the amount of fluoride and arsenic adsorbed onto ASBA increased with increasing temperature from 25℃ to 35℃, indicating that the adsorption was endothermic and non-spontaneous reaction. As a result of regeneration experiments, ASBA can be regenerated by 1N of NaOH. In the actual mine drainage experiment, it was found that it has relatively high removal rates of 77% and 69%. The experimental results show ASBA is effective as an adsorbent for removal fluoride and arsenic from mine drainage, which has a small flow rate and acid/neutral pH environment.

• Economic and Environmental Geology
• /
• v.55 no.2
• /
• pp.209-217
• /
• 2022

The purpose of this study was to confirm the dissolution of arsenic from the stabilized soil around abandoned coal mines by cultivation activities. Experimental soils were collected from the agricultural field around Okdong and Buguk coal mines, and the concentration of arsenic in the soil and the geochemical mobility were confirmed. The average arsenic concentration was 20 mg/kg. The soil with relatively high geochemical mobility of arsenic in the soil was used in the batch and column experiment. The limestone was mixed with soil for soil stabilization, and the mixing ratio was 3% of limestone, based on the soil weight. The phosphoric acid fertilizer (NH₄H₂PO₄) was added to the soil to simulate a cultivation condition according to the Rural Development Administration's rules. Comparative soil without mixing limestone was prepared and used as a control group. The arsenic extraction from soil was increased following the fertilizer mixing amount and it shows a positive relationship. The concentration of phosphate in the supernatant was relatively low under the condition of mixing limestone, which is determined to be result of binding precipitation of phosphate ions and calcium ions dissolved in limestone. Columns were set to mix phosphoric acid fertilizers and limestone corresponding to cultivation and stabilization conditions, and then the column test was conducted. The variations of arsenic extraction from the soil indicated that the stabilization was effectible until 10 P.V.; however, the stabilization effect of limestone decreased with time. Moreover, the geochemical mobility of arsenic has transformed by increasing the mobile fractions in soil compared to initial soil. Therefore, based on the arsenic extraction results, the cultivation activities using phosphoric fertilizer could induce a decrease in the stabilization effect.

• Economic and Environmental Geology
• /
• v.54 no.6
• /
• pp.671-687
• /
• 2021

This study investigated the firing temperature and thermal deformation process of roof tiles excavated from the connected stone-mound tomb in Seokchon-dong, Seoul, based on mineralogical and physical properties. A large number of roof tiles were excavated from the tomb site and some roof tiles were deformed by heat and were fired in uneven conditions. The colors of original roof tiles and their cores are mostly yellowish-brown, with high water absorption over 12%, containing fine-grained textures and some minerals such as quartz, feldspars, amphibole, and mica. It is estimated that the original roof tiles were fired below 900℃ in oxidation condition, showing loose matrices and mica layers by scanning electron microscopy. However, deformed roof tiles have the uneven surface color of reddish-brown and bluish-gray, and those cross-sections have sandwich structures in which dense reddish-brown surface and porous grey core coexist. They contained mullite and hercynite, so it was estimated to have been fired over 1,000℃, with 0.81~11% water absorption. In some samples, bloating pores by overfiring were observed, which means that they were fired at more than 1,200℃. In addition, the refirng experiments that the original roof tile was fired between 800℃ and 1,200℃ were carried out to investigate the physical and mineralogical properties of roof tiles compared to deformed ones. As a result, the water absorption decreased rapidly and the mineral phase started to change over 1,000℃. As the temperature gradually rises, the matrices are partially melted and recrystallized, resulting in similar thermal characteristics of deformed roof tiles. Therefore, the roof tiles from ancient tombs in Seokchon-dong seem to experience the secondary high temperature of 1,000 to 1,200℃ under uneven firing conditions, resulting in deformation characteristics such as shape transformation and mineral phase transition. It is considered to have been related to cremation rituals at the tombs of Seockchon-dong during the Baekje period.

• Economic and Environmental Geology
• /
• v.55 no.5
• /
• pp.511-519
• /
• 2022

In order to develop an air-stripping based remediation process to remove the TOC (Total Organic Carbon) in groundwater around the underground LPG storage cavern, the laboratory scale experiments at various conditions (change of air injection volume and temperature, the application of ultrasonic treatment, etc.) for two types of groundwater (initial TOC concentration of 608 mg/L and 153 mg/L, respectively). From results of experiment, as the air injection rate for stripping into groundwater increased from 2 L/min to 11 L/min and as the air-stripping time increased from 1 hour to 24 hour, the TOC removal efficiency of air-stripping increased. However, the TOC concentration of treated groundwater was higher than the discharge tolerance limit (100 mg/L) even after 24 hour stripping at the maximum air injection rate of 11 L/min. The main compounds of the TOC in groundwater were identified as methanol and propane and the long stripping time (more than 24 hour) was needed to separate the methanol from groundwater because of the affinity between water and methanol. At 20℃ and 4 L/min of air injection, the TOC removal efficiency increased to 59.1% after 24 hour air-stripping. When the temperature of groundwater increased to 30℃ and 40℃, the TOC removal efficiency increased up to 80.0% and 82.8%, suggesting that more than 24 hour air-stripping at 40℃ is needed to lower the TOC concentration to below 100 mg/L and the additional TOC removal process as well as the air-stripping is necessary. When the temperature increased to 60℃ and the ultrasonic treatment was conjugated with the air-stripping, the TOC removal efficiency increased to 87.8% within 5 hour stripping and the final TOC concentration (72.4 mg/L) was satisfied with the TOC discharge tolerance limit. The TOC removal efficiency for groundwater having low TOC concentration (153 mg/L) also showed similar removal efficiency of 89.7% (the final TOC concentration: 18.9 mg/L). Results in this study supported that the air-stripping conjugated with the ultrasonic treatment could remove successfully the TOC in groundwater around the underground LPG strorage cavern.