• Journal of Periodontal and Implant Science
• /
• v.29 no.2
• /
• pp.387-400
• /
• 1999

One of the fundamental causes of periodontal disease is accumulation of bacterial plaque and calculus and most effective method of removing these plaque and calculus are scaling and root planning using hand curet and ultrasonic scaler. Many studies concerning residual degenerated mineral content after periodontal therapies have been carried out, but some problems about these studies were also known. This research studies mineral concents and distribution of residual root surfaces after perfoming hand curet and ultrasonic scaler on root surfaces of single rooted teeth which were extracted for periodontal reasons. EPMA were used to avoid errors from chemical quantative analysis and in addition SEM observation was also performed. The results were as follows. 1. No differences were found between curet group andultrasonic scaler group in Ca, P, Mg and Na level. 2. Concentration level was decreased in the sequence of Ca, P, Mg and Na. 3. Ca and P level were decreased as going to apical portion at curet group and ultrasonic scaler group. 4. More cementum was removed at cervical portion compared to other portion at curet group and ultrasonic scaler group. 5. Ca, P, Mg level was higher in dentin compared to cememtum. There was no difference in mineral level for Ca, P, Mg and Na between root surfaces treated with hand curet and ultrasonic scaler.

• Tunnel and Underground Space
• /
• v.22 no.3
• /
• pp.221-225
• /
• 2012

Magnesium is one of the light weight materials, which can improve fuel economy and reduce emissions in automotive industry. Recently, magnesium alloys have gained considerable attention due to good mechanical properties. In this work, we have performed an explosive welding using the magnesium alloys (AZ31) and stainless steel (SUS 304). As a result, SUS304/AZ31 were successfully combined each other; however, a resolidified interlayer was observed at the point of welded layer. To reduce the resolidified interlayer, we have changed the thickness (0.5 mm and 1 mm) of stainless steel, distance (45 mm and 60 mm) between explosive and the center of materials and initial angle ($20^{\circ}$ and $30^{\circ}$) of explosive. In the case of the thickness 0.5 mm and angle of $30^{\circ}$, the resolidfied interlayer was not observed due to the increase of distance from the explosive. To accurately estimate the resolidified interlayer, electron probe micro-analyzer (EPMA) method and hardness were used. For the EPMA analysis, mixed materials were confirmed at the resolidified interlayer, and the measurement exhibited the middle value compared with the AZ31 and SUS304.

• Journal of the Korean earth science society
• /
• v.27 no.5
• /
• pp.521-527
• /
• 2006

The EPMA analysis for CHIME dating requires standard materials, which include nuclear fuel materials that are rare and sensitive to handle. Any laboratory that does not meet these standards has had difficulties adopting the CHIME dating method. We have developed a working standard technique for CHIME dating to prepare standard materials without use of nuclear fuel materials. Mineral samples, such as small pieces of monazite that are homogeneous in X-ray intensities, are calibrated using well-characterized primary standards in one laboratory. Once this procedure is done, they can be readily usable as working standards in the other laboratories, only with measurement of X-ray intensities. This method is applicable in preparing standard materials for both chemical compositions and determination of X-ray interference correction factors, and it is independent from chemical composition of mineral standard.

• Clean Technology
• /
• v.9 no.2
• /
• pp.57-61
• /
• 2003

A novel nitric acid-free desmut solution has been developed to remove smut, which is produced from a NaOH etching, on the surface of aluminum alloy metal in metal surface treatment processes. Comparing with the performance of 5% $HNO_3$ desmut solution, the mixed acid solution containing 2% $H_2O_2$, 0.5% HF, and 10% $H_2SO_4$ shows the same effect of smut removal for aluminum alloy samples of A16061 and A15052. To examine the surface alterations of the aluminum samples, in addition, the surface analysis is carried out with scanning electron microscopy (SEM) and electron probe microanalysis (EPMA).

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.51-56
• /
• 2002

The effect of kind of starting materials used for a sintering additive. magnesium acetate and magnesium nitrate, on the mechanical properties of alumina sintered body made by adding 1000 ppm of the additives, respectively, was investigated. As for the alumina sintered bodies prepared from magnesium acetate and magnesium nitrate, we observed that their relative densities decreased rapidly with increasing sintering temperature 1$600^{\circ}C$. Outer layer of alumina bodies had a duplex microstructure consisting of pores and grain growth. Also the inner layer had a second phase between alumina grain boundaries. By EPMA analysis, we confirmed that the grain boundary phase was a compound containing Mg.

• Journal of the Mineralogical Society of Korea
• /
• v.9 no.1
• /
• pp.43-53
• /
• 1996

The detailed crystal chemistry of ilmenite from the Hadong massif was studied by the EPMA, M ssbauer spectroscopy, and Rietveld structural refinement using X-ray powder diffraction data. The ilmenite-bearing anorthosite shows complicated mineral assemblage which consists of plagioclase, clinopyroxene, hornblende, biotite, chlorite, apatite, allanite, and zircon. Anorthite is andesine in composition (Ab 28-57), and clinopyroxene drops in ferro-hypersthene (Fs 62-70). Ilmenite is trigonal symmetry with R space group, whose structure shows the alternation of Fe2+ (M1 site) octahedral layer and Ti (M2 site) layer along c axis. M ssbauer spectroscopy indicates that there are three doubles which assigned to couple of Fe2+($\delta$=0.812, 0.890mm/sec) and one Fe3+($\delta$=0.303mm/sec) in octahedral sites. Their Fe3+/$\Sigma$Fe is 0.065 and chemical formula is established as Fe2+0.94Fe3+0.07Ti0.97O3 using both EPMA and M ssbauer analysis. Rietveld structural refinement reveals that site occupancies of Fe in M1 and Ti in M2 are 91.2% and 89.4%, respectively. This implies that Ti and Fe2+ are alternatively occupy M1 and M2 sites. In addition, smaller M2 site is more preferable to Fe3+ occupancy over M1.

• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.955-961
• /
• 2002

2.7vol%TiNi/6061 Al composites with TiNi shape memory alloy as reinforcement were fabricated by vacuum hot press. It was investigated by OM, SEM, EPMA and XRD analysis for the behavior of diffusion layer formation on various heat treatment condition. Thickness of diffusion layer was increased proportionally according to heat treatment time. The layer was formed by the mutual diffusion of TiNi and Al. The diffusion rate from TiNi fiber to Al matrix was faster than that of reverse diffusion path. The more diffused layer was formed in Al matrix. The diffusion at interface layer was consisted of $A1_3$Ti, $Al_3$Ni analyzed by EPMA, XRD results.

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.3
• /
• pp.367-375
• /
• 2005

Low-Z particle Electron Probe X-ray Microanalysis was applied to characterize MSW fly- and bottom -ash particle samples originated from two municipal incinerators (denoted as A and B) in Korea. According to their chemical composition, many distinctive particle types were identified. In A fly ash, the major chemical species are carbon-rich, aluminosilicates and many particles are composed of as a mixture of $ CaCO_3$ and other chemical species such as $CaSO_4$ or $CaCl_2$. For B fly ash, Fe, iron oxide, NaCl and NaCl-containing particles are the most abundant. In bottom ash, A and B were composed of similar chemical species such as carbon-rich, Fe, iron oxide, $CaCO_3$, and aluminosilicates. It was demonstrated that the single-particle characterization using this low-Z particle EPMA technique provided detailed information on various types of chemical species in the MSW ash samples. In addition, the technique has advantage over conventional analytical techniques in the point that both crystalline and glass-like ash particles can be analyzed at the same time.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.421-425
• /
• 2003

The reductive extraction process is an important step to refine the TRU product from the electrorefining process for the preparation of transmutation reactor fuel. In this study, it was studied on the reductive extraction between the eutectic salt and Bi metal phases. The solutes were zirconium and the rare earth elements, where zirconium was used as a surrogate for the transuranic(TRU) elements. All the experiments were performed in a glove box filled with a argon gas. Li-Bi alloy was used as a reducing agent to reduce the high chemical activity of Li. The reductive extraction characteristics were examined using ICP, XRD and EPMA analysis. The reduction reaction was equilibrated within 3 hours after the Li addition. Three eutectic salt systems were compared and Zr was successfully separated from the rare earth elements in all the three salt systems.

• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.595-600
• /
• 2020

The photovoltaic properties of perovskite solar cells (PSCs) with a carbon electrode fabricated using different annealing processes are investigated. Perovskite formation (50 ℃, 60 min) using a hot-plate and an oven is carried out on cells with a glass/fluorine doped TiO₂/TiO₂/ZrO₂/carbon structure, and the photovoltaic properties of the PSCs are analyzed using a solar simulator. The microstructures of the PSCs are characterized using an optical microscope, a field emission scanning electron microscope, and an electron probe micro-analyzer (EPMA). Photovoltaic analysis shows that the energy conversion efficiency of the samples fabricated using the hot-plate and the oven processes are 2.08% and 6.90%, respectively. Based on the microstructure of the samples and the results of the EPMA, perovskite is formed locally on the carbon electrode surface as the γ-butyrolactone (GBL) solvent evaporates and moves to the top of the carbon electrode due to heat from the bottom of the sample during the hot plate process. When the oven process is used, perovskite forms evenly inside the carbon electrode, as the GBL solvent evaporates extremely slowly because heat is supplied from all directions. The importance of the even formation of perovskite inside the carbon electrode is emphasized, and the feasibility of oven annealing is confirmed for PSCs with carbon electrodes.