• The KIPS Transactions:PartC
• /
• v.12C no.6 s.102
• /
• pp.781-792
• /
• 2005

This study proposes an Architecture for user level End-to-end Quality of Service(QoS) using overlay In Next Generation Network(NGN). Inexisting NGNs, the IMS of a control plane provides user QoS through direct traffic control and resource-reservation over the IP packet transport network of a user plane. Further, a set of torrent studies are ongoing not only to maximize the QoS for users, but also to minimize the quality deterioration for supporting the user End-to-end QoS. Along with that, an extended QoS in user level must be considered, for Instance, differentiating service quality to support users' expectation, providing optimized contents by users' equipments, and so forth. Accordingly, the Overlay Service Network Architecture proposed by this study provides protocol adaptation for maximum throughput on transport layer by using the most efficient transport layer protocol to various network circumstances. Also, the Overlay Service Network Architecture on application layer distributes processing delay from the data transformation process of the user equipment to the network, and it is capable of intermediate processing depending on user service level. application service feature, and equipment circumstance as well. Thus, this study mainly proposes the Overlay Service Network Architecture for user level end-to-end QoS in NGN with the quality control features both on the transport layer and the application layer, an internal component feature, and a service scenario providing the QoS linking with 3GPP.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.7
• /
• pp.379-385
• /
• 2008

In this paper, we propose an effective speech reinforcement technique under the near-end and the far-end noise environments. In general, since the intelligibility of the far-end speech for the near-end listener is significantly reduced under near-end noise environments, we require a far-end speech reinforcement approach to avoid this phenomena. Specifically, based on the estimated background noise spectrum of the near-end, we reinforce the far-end speech spectrum by incorporating the more general cases under the near-end with background noise. Also, we propose the novel approach to reinforce the actual speech signal except for the noise signal in the far-end noisy speech signal. The performance of the proposed algorithm is evaluated by the CCR (Comparison Category Rating) test of the method for subjective determination of transmission quality in ITU-T P.800 under various noise environments and shows better performances compared with the conventional method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2445-2450
• /
• 2003

Recently, biological technology industry shows great development. Instruments and systems related biological technology have been developed actively. In this paper, we developed a new micro end-effector for biological cell manipulation. The existing micro end-effector for biological cell manipulation has not any force sensing mechanism. Usually, excessive contact force occurring when the end-effector and a cell collide might make a damage on the cell. However, unfortunately, user can not notice the condition in case of using the existing end-effector. In order to overcome we proposed the improved micro end-effector having a force sensing mechanism. This paper presents the design concepts of the new micro end-effector. We carried out calibration of the force sensor and tested the performance of the proposed micro end-effector. Through a series of experiments the new micro end-effector shows the possibility of application for precision biological cell manipulation such as DNA operation

• Phonetics and Speech Sciences
• /
• v.10 no.1
• /
• pp.39-48
• /
• 2018

A typical statistical parametric speech synthesis (text-to-speech, TTS) system consists of separate modules, such as a text analysis module, an acoustic modeling module, and a speech synthesis module. This causes two problems: 1) expert knowledge of each module is required, and 2) errors generated in each module accumulate passing through each module. An end-to-end TTS system could avoid such problems by synthesizing voice signals directly from an input string. In this study, we implemented an end-to-end Korean TTS system using Google's Tacotron, which is an end-to-end TTS system based on a sequence-to-sequence model with attention mechanism. We used 4392 utterances spoken by a Korean female speaker, an amount that corresponds to 37% of the dataset Google used for training Tacotron. Our system obtained mean opinion score (MOS) 2.98 and degradation mean opinion score (DMOS) 3.25. We will discuss the factors which affected training of the system. Experiments demonstrate that the post-processing network needs to be designed considering output language and input characters and that according to the amount of training data, the maximum value of n for n-grams modeled by the encoder should be small enough.

• Annual Conference on Human and Language Technology
• /
• 2017.10a
• /
• pp.111-115
• /
• 2017

목적 지향적 대화 시스템(Goal-oriented dialogue system) 은 텍스트나 음성을 통해 특정한 목적을 수행 할 수 있는 시스템이다. 최근 RNN(recurrent neural networks)을 기반으로 대화 데이터를 end-to-end learning 방식으로 학습하여 대화 시스템을 구축하는데에 활용한 연구가 있다. End-to-end 방식의 학습은 도메인에 대한 지식 없이 학습 데이터 자체만으로 대화 시스템 구축을 위한 학습이 가능하다는 장점이 있지만 도메인 지식을 학습하기 위해서는 많은 양의 데이터가 필요하다는 단점이 존재한다. 이에 본 논문에서는 도메인 특정 지식을 결합하여 end-to-end learning 방식의 학습이 가능한 Hybrid Code Network 구조를 기반으로 한국어로 구성된 식당 예약에 관련한 대화 데이터셋을 이용하여 식당 예약을 목적으로하는 대화 시스템을 구축하는 방법을 제안한다. 실험 결과 본 시스템은 응답 별 정확도 95%와 대화 별 정확도 63%의 성능을 나타냈다.

• Korean Journal of Poultry Science
• /
• v.24 no.1
• /
• pp.29-37
• /
• 1997

An experiment was conducted for 20 days( from July 21 to August 10, 1996) to investigate the differences in thickness of eggshell and eggshell membrane in Korean native chicken. All the eggs were purchased from a farm located in Chinju area. All eggs were categorized into Treatment I (34.89~51.39 g), H (53.32~60.70 g), and III (34.89~60.70 g) according to their weights. Eleven items were measured in all three treatments, i.e., egg weight, egg length, egg width, breaking strength, eggshell thickness of large end(STLE), eggshell membrane thickness of large end(SMTL), eggshell thickness of small end (STSE), eggshell membrane thickness of small end(SMTS), eggshell thickness of middle part(STMP), and eggshell membrane thickness of middle part(SMTM). Correlation coefficients between egg weight and eggshell weight, among eggshell thickness of large end, small end and middle end and eggshell weight were significant (P<0.01). Correlation coefficients between egg weight and large eggshell membrane were nega-tively significant(P<0.01). Breaking strengths were higher in Treatment I than in Treatment H. Correlation coefficients among thickness of eggshell and eggshell membrane at each point at 3 parts of large end, small end and middle end were not significant.

• The Journal of Information Systems
• /
• v.10 no.1
• /
• pp.73-95
• /
• 2001

A significant body of information systems research is concerned with user participation as a means to improve user satisfaction within systems development. In spite of the many studies in this area, findings are not consistent or cumulative. One of the reasons for this is not to be considered the type of systems. Most research are focusing on traditional system development under the mainframe environment instead of under end-user based environment like web-based information system or ERP. End-user based environment requires user's strong initiatives in the system development life cycle. It means the user\`s simple participation is not enough and user-led-development is more appropriate for the system success. This paper can call this new concept is end-user joint work which means user has to participate in the system development as a co-developer. This paper investigates how the end-user joint work contributes end-user satisfaction and two variables in particular-job complexity and technical competence-moderate the outcomes of end-user joint work Analysis of 112 independent systems development projects indicated that end-user joint work has a direct relationship with end-user satisfaction. In addition, the two variables were found to moderate key roles on this relationship. That is, the strength of this relationship depended on the level of these factors.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.4
• /
• pp.19-24
• /
• 2003

In end milling process, which is characterized by the use of a rotating tool, the undeformed chip thickness varies periodically with phase change of the tool. Although many efforts have concentrated on the study of end milling process, the analysis of shear and chip-tool friction behaviors has not been reported. Recently, a model has been proposed to simulate the shear and friction characteristics of an up-end milling process in terms of the equivalent oblique cutting. In the current study, the varying undeformed chip thickness and the cutting forces in a down-end milling process are replaced with the equivalent ones of oblique cutting. Then it is possible to simulate the shear and the chip-tool friction characteristics of a down-end milling process. The proposed model has been verified through two sets of cutting tests i.e., down-end milling and the equivalent oblique cutting tests. The experimental results show that the proposed model is suitable to analyze the shear and chip-tool frictional characteristics of down-end milling process. The specific cutting energy decreases with increase in equivalent undeformed chip thickness in a down-end milling process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.344-349
• /
• 2005

This paper is studied on the effect of TiAlN coated ball end mill on cutting characteristic of high hardness steels in dry cutting condition without coolant. KP4 steels[HRC32] and STD11[HRC60] heat treated steels wert: used as the workpiece and WC-Co ball end mill and single and multi layer TiAlN coated ball end mill were utilized. Results showed that TiAlN coated ball end mill were increased the cutting length than WC-Co ball end mill in the cutting speed$[245\~320m/min]$ about $2\~5$ times for KP4 steels and about $2.7\~4.3$ times for STD11 heat treated steels. The multi layer TiAlN coated ball end mill is good about $1.2\~1.7$ times for KP4 steels and STD11 steels than single layer coated.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.1 s.149
• /
• pp.12-19
• /
• 2006

This study was administered to identify features of masstiege high-end products by comparing to original old high-end products. For this purpose, the differences in shopping orientation between each consumer groups by product types(high-end products, original old high-end products) preferred were examined. 300 female consumers were surveyed and 279 data were used for analysis. The results are as follows. First, three elements(efficiency, enjoyment, convenience) of shopping orientation were constructed by factor analysis and efficiency element of all elements had highest explanation power. The differences in shopping orientation between masstiege high-end products and original old high-end products were identified by t-test. The consumers preferring original old high-end products regarded convenience element as an important factor and the consumers preferring masstiege high-end products considered efficiency element more. The correlation analysis between shopping orientation factors and demographic characteristics were administered. The consumers who were of low age, low education, low income and unmarried pursued efficiency more, the consumers who were unmarried, of high education and high income showed to pursue enjoyment more, and the consumers who were of high age, high education, high income and married considered convenience element more. Finally marketing strategies for masstiege brands were suggested.