• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.12
• /
• pp.125-130
• /
• 2004

The characteristics of on-chip spiral rectangular inductors in CMOS process are investigated through the simulation and experiment. The ADS-momentum is used for EM simulation, and the spiral inductors are fabricated with Hynix 0.35㎛ CMOS process. This research mainly concerned the effects of the geometric change in terms of the number of turns and the width of micro strip line. The measured and simulated results show that the Hynix 0.35㎛ process could support a top metal spiral inductor of 1nH to 6nH with Q-factor less than 5.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.9
• /
• pp.1108-1119
• /
• 2016

This paper presents the spectral analysis and radiation pattern of low-frequency electromagnetic(EM) leakage signals according to the fundamental operations of smartphones. The EM leakage signals generated by the activation of four I/O sensor modules such as a touch-screen, a camera, a microphone and a speaker are captured by the commercial near-field magnetic probe with 1cm spatial resolution. The analysis results show that the leakage of the EM wave occurs strongly around the activated I/O sensor modules, AP(Application Processor) and memory modules. Also, the distinguishable frequency characteristic is shown in each spectrum of EM leakage signals.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2021

In this paper, the cabinet shielding effectiveness (SE) including digital modules for nuclear power plants is analyzed depending on the internal structure and electromagnetic (EM) wave incidence angle. To analyze the SE, the cabinet and modules are modeled using the FEKO EM simulation tool. The SE is then obtained by comparing the electric field with and without the cabinet. In addition, the cabinet SE is observed by changing various conditions such as the spacing of each digital module, incidence angle, and the polarization of the EM wave at the 2.4 G[Hz frequency. To verify the results, the dipole antenna for SE measurements is fabricated, and the SE is measured in a semi-anechoic chamber. The result demonstrates that the SE by the cabinet structure can be expected to be higher when the polarization of the incident EM wave is horizontal to the ground and the distance between the digital modules is wide.

• Journal of Acupuncture Research
• /
• v.33 no.2
• /
• pp.117-133
• /
• 2016

Objectives : Traditional Korean Emergency Medicine (EM) has been developing for thousands of years, however its value was not properly considered after 19th century modernization. The purpose of this study was to review the current status of EM in Korean Medicine and suggest methods for improvement. Methods : We performed systematic reviews of the definition, current medical system, and educational curriculum of EM in Western Medicine, traditional Korean and Chinese Medicine, and integrated Western and traditional Chinese medicine with the use of medical classics and text books. We also analyzed the trends in published research articles to discuss the current situation in the field of traditional Korean EM, and to provide methods for its establishment and development with traditional Korean medicine. Results : The definition of EM as a treatment of acute disease shares common understanding among traditional Korean, Chinese, and Western medicine. We presented descriptions of EM in many medical classics, however current law and EM service does not include these. As for the review of publications during the last 20 years, we found 21 articles in several fields that confirmed the need for more investigation. Conclusion : Traditional Korean EM has a long history and clinical experiences that can be found in medical classics, textbooks and research articles. There is an urgent need for more studies on traditional Korean EM as an emergency medical service system, and in terms of educational curriculum and related policies to improve Evidence-Based teaching.

• Geophysics and Geophysical Exploration
• /
• v.17 no.3
• /
• pp.163-170
• /
• 2014

Development of a modeling technique for accurately interpreting electromagnetic (EM) data is increasingly required. We introduce finite difference (FD) and finite-element (FE) methods for three-dimensional (3D) frequency-domain EM modeling. In the controlled-source EM methods, formulating the governing equations into a secondary electric field enables us to avoid a singularity problem at the source point. The secondary electric field is discretized using the FD or FE methods for the model region. We represent iterative and direct methods to solve the system of equations resulting from the FD or FE schemes. By applying the static divergence correction in the iterative method, the rate of convergence is dramatically improved, and it is particularly useful to compute a model including surface topography in the FD method. Finally, as an example of an airborne EM survey, we present 3D modeling using the FD method.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.9 no.6
• /
• pp.711-718
• /
• 2019

Spectrum analyzer and electromagnetic field meter were used to investigate the EM generation behaviour in different types of home electrical appliances. During microwave oven operation, the EM power measured at a point 30cm apart was measured in the range of 8~11mW/㎡, the strength of the low frequency magnetic field was 60~80mG and the electric field strength was measured at 150~160V/m. For smart phone wireless charging pad, it was measured at an electromagnetic power of 0.4mW/㎡, an electric field of 160 V/m and a magnetic field of 1mG at a point 10cm away. For microwave oven and wireless charging pad, if used within 10cm, the size of the electric field has been measured at a large value that exceeds the human body protection standard and may be hazardous to humans. On the other hand, home appliances such as TVs, hairdryers and refrigerators all showed very low levels of electromagnetic waves, electric fields and magnetic fields, with no harmful effects seen. For electromagnetic shielding, the metal Cu fabric and metal foil had a high level of EM shielding, while polymer films had a low EM shielding characteristic.

• Journal of Korean Institute of Industrial Engineers
• /
• v.33 no.1
• /
• pp.52-60
• /
• 2007

Estimating parameters of the lifetime distribution is investigated when field failure data are not completelyreported. To take into account the reality and the accuracy of the estimates in such a case, the failure reportingprobability is incorporated in estimating parameters, Firstly, method of maximum likelihood estimate (MLE) isused to estimate parameters of the lifetime distribution when failure reporting probability is known, Secondly,Expectation and Maximization (EM) algorithm is used to estimate the failure reporting probability and parame-ters of the lifetime distribution simultaneously when failure reporting probability is unknown. For both cases,procedures of estimation are illustrated for single Weibull distribution and mixed Weibull distribution. Simula-tion results show that MLE obtained by the proposed method is more accurate than the conventional MLE.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.1
• /
• pp.37-45
• /
• 1991

The electromagnetic field distribution within rectangular coaxial transmission lines (RCTL:TEM cells) is calculated using a numerical method. Boundary integral equations(BIE) considering equivalence theorem and extended boundary condition(EBC) in tapered region are used, thereby restricting the operational frequencies (0~130 MHz) below the cell cutoff frequency(130 MHz). The EM fields within NIST TEM cell ($1\times0.6\times2m$) are calculated by this method. The results of the numerical calcuation have a good agreement in the cross-sectional EM field distribution of TEM cell with 2-dimensional analysis results. Based on this method, the first cutoff freque- ncy in high order modes in the cell and the electric field polarization are considered.

• Journal of electromagnetic engineering and science
• /
• v.13 no.3
• /
• pp.192-194
• /
• 2013

This paper proposes a validation model using a reverberation chamber for verification of the effectiveness and accuracy of the statistical power balance (PWB) method. The PWB method treats electromagnetic (EM) field distributions in certain environments as a representative value of an "ensemble" average, so a reverberation chamber is utilized as a testing apparatus to experimentally simulate the sets of measurement field "ensemble" inside a complex environment. Measurements are performed with various test conditions for environmental loss using flat absorbers, and front and side doors of the chamber. Comparison between the PWB analysis and the measurement results shows good agreement, indicating the usefulness of this statistical analysis method for stating the electromagnetic field inside the EM zone as a representative value to general structures.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.51-52
• /
• 2014

Non-destructive technique to measure internal structure and constant distribution of material can be widely used to exploration of mineral resources, identification of underground cables and buried pipelines, and diagnostic imaging in medical area. In this paper, we considered 2-dimensional EM scattering problem. Radiation pattern in far field is estimated by using some measured information obtained from near-field solutions.