• Journal of Life Science
• /
• v.17 no.12
• /
• pp.1701-1708
• /
• 2007

Seed pelleting is generally conducted in order to save the labor for sowing and thinning by enabling the precision mechanical planting. In the present study, the influence of physical and chemical properties of pelleting solid materials was investigated on carrot seed germination. Among the pelleting solid materials evaluated, dialite, kaolin, and talc showed low bulk density and high porosity. Bentonite and dialite carried high water holding capacities of 184% and 173%, respectively, while calcium carbonate, calcium oxide, and fly ash showed relatively low water holding capacity. The pH of kaolin (6.8) and dialite (7.4) were close to neutral, while limestone (12.8), calcium oxide (13.0), and bentonite (10.0) were highly basic. High electro-conductivity was shown in limestone and calcium oxide. EDS analysis revealed that the main elemental compositions of talc were Si (71.0%) and Mg (29.0%), and those of calcium carbonate were Ca (66.6%), Si (22.9%), and Mg (10.5%). High granulation capacity was observed from talc and the mixture of talc and calcium carbonate. Seeds pelleted with bentonite showed the highest hardness. The dissolving type of the pellet layer after imbibition was split type in talc, limestone, zeolite, and fly ash, melt type in calcium carbonate and calcium oxide, and swell type in bentonite and vermiculite. The shortest dissolving time of pellet layer was observed from calcium carbonate and kaolin. The germination speed $(T_{50})$ was delayed as the size of pelleted seeds increased. The optimum size of pelleting was 19 ratio in carrot.

• Economic and Environmental Geology
• /
• v.35 no.3
• /
• pp.241-255
• /
• 2002

The purpose of this study is to investigate environmental geochemical characteristics for the acid mine drainage and stream sediments in the abandoned Honam coal mine area. For the chemical analysis, stream winter samples were collected at 54 sites and for the mineralogical and chemical analysis, stream sediments samples were collected at 34 sites. Physical and chemical characteristics of stream water were measured at the site and chemical compositions were analyzed by ICP-AES, ICP-MS and IC. Mineralogical characteristics of stream sediments samples were determined using XRD, SEM and EDS. In physical and chemical properties, stream water shows thats pH 2.85~8.12, Eh -62~215 mV, EC 0.205~146 ms/m, ER 0.234~255 {$\Omega}{\cdot}$m, DO 0.03~1068 mg/L and TDS 10.96~1420mg/L. In chemical compositions, we obtain that K 0.118~3.184 mg/L, Mg 2.1~114.48 mg/L, Ca 2.59~l25.02 mg/L, Al 0.01~44.72 mg/L, Fe 0.108~89.49 mg/L and Na 5.45~125.41 mg/L. Stream sediments are commonly composed of quartz, illite and goethite in the result of x-ray diffraction. After heat treatment at 98$0^{\circ}C$, the hematite peaks are distinctly shown. In consideration of heavy metals (include Fe) for steam sediments, Fe ranges 22575~34713 ppm, Zn 41.66~970.3 ppm, Cd 0.52~52.07 ppm, Cu 1.25~198.5 ppm and Pb 0.43~77.35 ppm.

• Journal of the Korean Society of Child Welfare
• /
• no.59
• /
• pp.209-234
• /
• 2017

This study viewed schools as a cause of students dropping out and posited that dropping out of high school would vary depending on the characteristics and influencing factors of the school from which students were dropping out. Therefore, focusing on schools, we longitudinally investigated the change patterns of school dropout across high schools in the country, and the types of changes in dropping out of high school. In addition, we predicted the general characteristics of schools according to the type of school students were dropping out from, looked at the changes in the major factors (i.e., school violence and school counseling) affecting school dropout, and reviewed schools' long-term efforts and outcomes in relation to school dropout. For this purpose, KERIS EDSS's "Secondary School Information Disclosure Data" were used. The final model included data collected five years20122016) from high schools across the country. The results were as follows. First, in order to examine the longitudinal change patterns of dropping out of high schools, a latent growth models analysis was conducted, and it revealed that, as time passed, the dropout rate decreased. Second, growth mixture modeling was used to explore types according to the change patterns of the school students were dropping out from. The results showed three types: the "remaining in school" type, the "gradually decreasing school dropout" type, and the "increasing school dropping out". Third, the multinomial logistic regression was conducted to predict the general characteristics of schools by type. The results showed that public schools, vocational schools, and schools with a large number of students who have below the basic levels in Korean, English and mathematics were more likely to belong to the "increasing school dropout" type. Further, the larger the total number of students, the higher the probability of belonging to the "remaining in school" type or the "gradually decreasing school dropout" type. Lastly, growth mixture modeling was used to analyze the trend of school violence and school counseling according to the three types. The focus was on the "gradually decreasing school dropout" type. In the case of the "gradually decreasing school dropout" type, it was found that as time passed, the number of school violence cases and the number of offenders gradually decreased. In addition, in terms of change in school counseling the results revealed that the number of placement of professional counselors in schools increased every year and peer counseling was continuously promoted, which may account for the "gradually decreasing school dropout" type.

• Clean Technology
• /
• v.25 no.1
• /
• pp.81-90
• /
• 2019

A dielectric barrier discharge (DBD) plasma reactor packed with $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst was used for the dry ($CO_2$) reforming of propane (DRP) to improve the production of syngas (a mixture of $H_2$ and CO) and the catalyst stability. The plasma-catalytic DRP was carried out with either thermally or plasma-reduced $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst at a $C_3H_8/CO_2$ ratio of 1/3 and a total feed gas flow rate of $300mL\;min^{-1}$. The catalytic activities associated with the DRP were evaluated in the range of $500{\sim}600^{\circ}C$. Following the calcination in ambient air, the ${\gamma}-Al_2O_3$ impregnated with the precursor solution ($Ni(NO_3)_2$ and $Ce(NO_3)_2$) was subjected to reduction in an $H_2/Ar$ atmosphere to prepare $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst. The characteristics of the catalysts were examined using X-ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectrometry (EDS), temperature programmed reduction ($H_2-TPR$), temperature programmed desorption ($H_2-TPD$, $CO_2-TPD$), temperature programmed oxidation (TPO), and Raman spectroscopy. The investigation revealed that the plasma-reduced $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst exhibited superior catalytic activity for the production of syngas, compared to the thermally reduced catalyst. Besides, the plasma-reduced $Ni-CeO_2/{\gamma}-Al_2O_3$ catalyst was found to show long-term catalytic stability with respect to coke resistance that is main concern regarding the DRP process.

• Korean Journal of Heritage: History & Science
• /
• v.47 no.4
• /
• pp.224-243
• /
• 2014

This study examined the materials and casting technology(cast, alloy, etc.) used in the manufacturing of bronze artifacts based on old literature such as Yongjae Chonghwa, Cheongong Geamul, and The Korea Review. In the casting experiment for restoration of Sangpyong Tongbo, a bronze and brass mother coin mold was made using the sand mold casting method described in The Korea Review. The cast was comprised of the original mold plate frame, wooden frame, and molding sand. Depending on the material of the outer frame, which contains the molding sand, the original mold plate frame can be either a wooden frame or steel frame. For the molding sand, light yellow-colored sand of the Jeonbuk Iri region was used. Next, the composition of the mother alloy used in the restoration of Sangpyong Tongbo was studied. In consideration of the evaporation of tin and lead during actual restoration, the composition of Cu 60%, Zn 30%, and Pb 10% for brass as stated in The Korea Review was modified to Cu 60%, Zn 35%, and Pb 15%. For bronze, based on the composition of Cu 80%, Sn 6%, and Pb 14% used for Haedong Tongbo, the composition was set as Cu 80%, Sn 11%, and Pb 19%. The mother coin mold was restored by first creating a wooden father coin, making a cast from the wooden frame and basic steel frame, alloying, casting, and making a mother coin. Component analysis was conducted on the mother alloy of the restored Sangpyong Tongbo, and its primary and secondary casts. The bronze mother alloy saw a 5% increase in copper and 4% reduction in lead. The brass parent alloy had a 5% increase in copper, but a 4% and 12% decrease in lead and tin respectively. Analysis of the primary and secondary mother coin molds using an energy dispersive spectrometer showed that the bronze mother coin mold had a reduced amount of lead, while the brass mother coin mold had less tin. This can be explained by the evaporation of lead and tin in the melting of the primary mother coin mold. In addition, the ${\alpha}$-phase and lead particles were found in the mother alloy of bronze and brass, as well as the microstructure of the primary and secondary coin molds. Impurities such as Al and Si were observed only in the brass mother coin mold.

• Journal of The Korean Society of Clinical Toxicology
• /
• v.18 no.2
• /
• pp.57-65
• /
• 2020

Purpose: Since 2012, acetaminophen can be accessed easily not only at pharmacies but also at convenience stores. The relationship between the easy access of acetaminophen and the risk of poisoning has been controversial. Several studies also reported different results regarding the risk of acetaminophen poisoning after access to acetaminophen was relaxed. This study examined the long-term effects on the risk of acetaminophen poisoning after easy access to acetaminophen was implemented. Methods: This was a retrospective analysis of an emergency department (ED)-based in-depth Injury Surveillance Cohort by the Korea Center for Disease Control and prevention from 2011 to 2018. Poisoning cases were selected from the Cohort, and the incidence of acetaminophen poisoning and the characteristics of the cases of acetaminophen poisoning were analyzed. The purchase path and the amount of ingestion in acetaminophen poisoning were sub-analyzed from data of six EDs. Results: Of 57,326 poisoning cases, 4.0% (2,272 cases) were acetaminophen poisoning. Of 2,272 cases of acetaminophen poisoning, 42.8% (974 cases) required in-patient care after ED management. Two hundred and sixty-four of these 964 cases required intensive care. The rates of cases that required in-patient treatment and the rates of cases that required intensive care increased from 29.4% in 2011 to 48.1% in 2018, and from 3.1% in 2011 to 15.2% in 2018, respectively (p<0.001, p<0.001). In the poisoning group with in-depth toxic surveillance (n=15,908), the incidence and proportion of acetaminophen (AAP) poisoning increased from 55 cases per year to 187 cases per year and 4.9% to 6.1%, respectively (p=0.009, p<0.001, respectively). The most common age group of acetaminophen poisoning was teenagers, which is different from the most common age group of other pharmaceutical agents: the middle age group of 40-49 years (p<0.001). Of 15,908 in-depth toxic surveillance patients, 693 patients had AAP poisoning, of whom 377 cases (54.2%) purchased acetaminophen from a non-pharmacy. The proportions of the purchase path from non-pharmacy were 41.4% at 2011-12 and 56.4% (2013-18) (p=0.004). The amount of acetaminophen ingestion was 13.5±14.3 g at 2011-12 and 13.9±15.1 g at 2013-18 (p=0.794). Conclusion: Although the incidence of acetaminophen poisoning did not increase remarkably in the short term after the implementation of the new regulation, the incidence of acetaminophen poisoning has increased slightly during the study period of 2017-18. In addition, the proportion of the purchase path from non-pharmacies has increased since the emergence of new regulations for the easy access of acetaminophen in 2012. The incidence of acetaminophen poisoning might have been affected after the increasing accessibility of acetaminophen in convenience stores. Continuous control of acetaminophen poisoning is required. Furthermore, the prevention of acetaminophen poisoning should be focused on teenagers with specialized school education programs.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.100-117
• /
• 2020

National Treasure no. 101, the stupa of State Preceptor Jigwang from the Beopcheonsa Temple Site in Wonju has been transferred from place to place and reassembled several times since it was built. In particular, overall dismantling and repair was carried out in 1957 to restore parts damaged by bombing during the Korean War. Documented information on the repair process and materials used at that time does not exist. However, various types of metal materials used for this stupa have been identified during conservation work. Besides clamps anchor bolts, 9mm-thick circular rebars were mainly used for joining the parts of this stupa, while circular rebars and wires of various thicknesses were used for joining the parts with mortar restoration materials. Although deformed bars are typically used for stone pagodas classified as architectural structures, smooth circular rebars were used in this case. In terms of restoration using mortar, material shapes were transformed, bound alternately, and twisted irregularly to improve bonding strength and coherence in order to insert restoration materials and to bolster structural weaknesses. In addition, metallographic analysis showed the material to be hypo-eutectoid steel with low carbon content. Many non-metallic inclusions in the shape of drops of different sizes were included, which do not affect the whole elemental composition due to the very small quantities involved. Qualitative and EPMA analysis of Mn and S, which were not identified by SEM-EDS area analysis, established an even distribution of MnS in crystal grains of the microstructure, regardless of the shape of the samples. It is presumed that secondary homogenization and softening might have been conducted after manufacturing to facilitate the working process. Furthermore, in consideration of properties indicating that the thinner the steel is, the less carbon content contained and the greater the elasticity and elongation, it is judged that restoration work was ordered.

• Journal of Conservation Science
• /
• v.37 no.6
• /
• pp.723-737
• /
• 2021

This study analyzed the composition and structure of materials with Buddhist paper scriptures excavated from architectural sites in 'Sum Tolgoi' of the 17^th century and carried out conservation treatment base on the result of the analysis. The scriptures were covered in dust and foreign sub stances, and were so crumpled that it was impossible to identify the form. The damage, loss, and discoloration have been identified. Buddhist scriptures written in Tibetan used indigo and ink sticks on paper as a result of UV-Vis analysis, and ink sticks as black character materials from scriptures written ancient Mongolian. SEM-EDS and Micro-XRF analyses revealed that the outlines were drawn with red lines using a mix of Minium (Pb₃O₄) and Cinnabar (HgS), or Cinnabar (HgS) alone, and the contents of the scriptures were written with silver paint. Silver chloride (AgCl) and Calcium (Ca) were identified in the silver paint component of the characters, while Calcium and Orpiment (As₂S₃) were identified in the yellow lines. Concerning the paper ground, Buddhist scriptures written in ancient Mongolian were characterized by herbal plant fiber and bast fiber, and those written in Tibetan, by bast fiber. Radiocarbon dating indicates that the paper for the scriptures was produced between the 15^th and 17^th centuries. Conservation treatment of the scriptures was carried out based on the experiment on the production of pre-coated paper and how to coat that to prevent the second damage due to the deformation and fragility of the excavated paper. The scriptures were preserved and mounted, and a neutral box was made to identify the contents of the scriptures recorded on both sides after the treatment. This conservation treatment is the result of a study that applied new conservation treatment materials and methods according to the principle of conservation treatment reversibility.

• Korean Journal of Heritage: History & Science
• /
• v.57 no.1
• /
• pp.146-159
• /
• 2024

In this study, a study on the production technology of the Buddha statue and the production of raw material origin was conducted through scientific analysis on the Bronze seated Bodhisattva Statue of Goseongsa Temple, a treasure. As a result of microstructure analysis through a metal microscope, it was confirmed that the microstructure of the Bronze seated Bodhisattva Statue of Goseongsa Temple was a process-type dendritic structure, and the casting structure of bronze was well represented, so it was manufactured through casting. Subsequently, as a result of analyzing the alloy composition ratio through SEM-EDS, it was identified as a ternary alloy with 81.26 wt% of copper (Cu) and 16.42 wt% of tin (Sn) and 1.72 wt% of lead (Pb). The results of the analysis of lead isotope ratios using a thermal ionization mass spectrometer (TIMS) were substituted into the distribution of lead isotope ratios on the Korean Peninsula, it was shown in corresponding to Jeolla-do and Chungcheong-do regions and North and South Gyeongsang Province. This suggests that the raw materials used in their production were likely sourced from the mines around Goseong Temple in Gangjin. Despite the fact that the statue is a medium and large Buddha with a total height of 51 centimeters, 1.72 wt% of lead (Pb) was found as a result of alloy composition ratio analysis, which showed a similar composition to the lead content ratio of small bronze and gilt-bronze Buddha statues. Therefore, we compared and analyzed the results of the analysis of the composition ratio of the alloys of bronze and gilt bronze statues, which has been scientifically analyzed with a compositional age similar to that of the Bronze seated Bodhisattva Statue of Goseongsa Temple. Comparison results, Various factors, such as the size of the Buddha statue as well as its stylistic characteristics and the age of composition, may exist in determining the alloy composition ratio of the bronze and gilt bronze Buddha statues, and it was confirmed that the alloy composition ratio or casting technology was properly adjusted when the Buddha statue was created. In other words, it is judged that a more comprehensive system of Buddha statue production technology should be investigated by conducting archaeological and art history studies on stylistic characteristics and age of composition, as well as scientific analysis results such as observation of internal structure, microstructure observation, and analysis of alloy composition ratio using radiation transmission irradiation.