• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -1
• /
• pp.233-236
• /
• 2000

A portable equipment that measures a current and voltage waveform of power transmission lines is pro-posed. In the equipment, the current and voltage, respectively, are detected by a loop coil and a capacitor clamped around the power lines. The detected data is transmitted by an FM wave to the receiver on the ground station. Since the receiver is isolated from the power lines, we do not require high potential insulators for the measurement of current and voltage. The proposed equipment is therefore, small-sized, light, and low in the cost of production. Experimental results presented here show that the equipment can monitor the current flowing in single wire over a ground plane and the potential of the wire.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 추계학술대회 논문집
• /
• pp.103-107
• /
• 2002

A contact-less power supply system (CPS) allows electrical energy to supply to mobile consumers without any electrical or mechanical contact. CPS works in the same principle as a transformer, with the track litz cable forming the primary circuit and the pickup as the secondary. The track power supply generates the high frequency alternating current in the track cable. The captured AC magnetic field generated by the track conductors produces electrical energy in the pickup coil and the pickup rectifier converts the high frequency AC power to DC while regulating the power to the load. This paper presents the theoretical analysis, simulation and experiment리 results of the series-parallel resonant converter working as contact-less power supply system.

• 조명전기설비학회논문지
• /
• 제28권7호
• /
• pp.62-68
• /
• 2014

We proposed a series connection-type superconducting fault current limiter(SFCL) using E-I core that can prevent the internal magnetic flux generation of cores during normal operation, and prevent the saturation of cores due to a sudden magnetic flux generation at the initial stage of fault occurrence while limiting the peak current. Through a short-circuit simulation experiment, we analyzed the operating status of the two superconducting elements and limiting characteristics according to the size of the fault current peak before and after the failure. Further, the double peak current limiting characteristics according to the winding directions as well as the current and the voltage of each coil were compared and analyzed.

• 한국초전도ㆍ저온공학회논문지
• /
• 제10권1호
• /
• pp.57-61
• /
• 2008

A 1MW class HTS(High-Temperature Superconducting) synchronous motor has been developed. This motor was aimed to be utilized for industrial application such as large motors operating in large plants. The HTS field windings of the developed motor is cooled by way of Neon thermosiphon mechanism and the stator coil is cooled by water through hollow copper conductor. This paper describes performance test results of our motor, which was conducted at steady state in generator mode and motor mode.

• 한국광학회지
• /
• 제5권3호
• /
• pp.386-393
• /
• 1994

XeCl 엑시머 레이저를 횡방향의 전자빔으로 여기하여 이의 출력특성을 조사하였다. 전자빔의 출력은 880kV, 21kA(70ns, FWHM)이며 전자빔의 전류밀도는 다이오드(A-K) 간격과 공진기 외부에 설치한 펄스자계코일(4.7kG)로 제어하였다. 레이저 매질에 주입되는 전자빔의 축적에너지는 35J(4기압)이다. 축적에너지는 Radcolor film의 감광면적과 압력상승법에 의해 측정한 가스매질의 상승압력으로부터 환산된 수치이며, 이 때의 여기체적은 $320cm^{3}$이었다. 레이저 가스의 혼합비율은 HCl/Xe/Ar=0.2/6.3/93.5%이고 총압력이 3기압일 때, 최대효율 1.7%를 얻었다. 이 때의 출력에너지, 특성에너지는 각각 0.52J, 1.7J/l이었다. 실험결과의 분석을 위해 컴퓨터 시뮬레이션코드를 완성하였다. 시뮬레이션 결과는 실험결과와 잘 부합하고 있음을 확인하였고 그 결과를 이용하여 XeCl의 형성채널, 완화채널, 308nm의 흡수채널을 이론적으로 설명하였다.

• Asian Journal of Atmospheric Environment
• /
• 제9권2호
• /
• pp.146-157
• /
• 2015

Emissions of ozone precursors ($NO_x$ and VOCs) and photochemical ozone creation potentials (POCPs) of VOC emission sources were investigated in the largest port city (i.e., Busan), Korea during the year 2011. This analysis was performed using the Clean Air Policy Support System (CAPSS) national emission inventory provided by the National Institute of Environmental Research (NIER), Korea. For $NO_x$, the emissions from off-road mobile sources in Busan were the most dominant (e.g., $31,202ton\;yr^{-1}$), accounting for about 60% of the total $NO_x$ emissions. The emission from shipping of off-road mobile sources (e.g., $24,922ton\;yr^{-1}$) was a major contributor to their total emissions, amounting to 47% of the total $NO_x$ emissions due to the port-related activities in Busan. For VOCs, the emission source category of solvent usage was predominant (e.g., $36,062ton\;yr^{-1}$), accounting for approximately 82% of the total VOC emissions. Out of solvent usages, the emission from painting was the most dominant ($22,733ton\;yr^{-1}$), comprising 52% of the total emissions from solvent usages. The most dominant VOC species emitted from their sources in Busan was toluene, followed by xylene, butane, ethylbenzene, n-butanol, isopropyl alcohol, and propane. The major emission sources of toluene and xylene were found to be painting of coil coating and ship building, respectively. The value of POCP for the off-road mobile source (61) was the highest in ten major activity sectors of VOC emissions. Since the POCP value of ship transport of off-road mobile source (72) was also high enough to affect ozone concentration, the ship emission can play a significant role in ozone production of the port city like Busan.

• 한국농공학회지
• /
• 제17권1호
• /
• pp.3702-3711
• /
• 1975

This study was originated to investigate the imparired parts of the mist and dust blowers and intended to analyze the causes of their failures by the use of the Weibull probability paper. By the use of the paper, the parts which were needed to change the design, the force of the urgency, the mean time between failures of the parts and the basic causes of the troubles could be predicted. The survey showed that the following parts got out of order: (A) flexible rubber hose, (B) blowing fan, (C) lead valve, (D) piston ring. (E) crank main bearing, (F) coil in magneto and (G) needle valve in carburettor. The analysis of the survey indicated that the parts G, C, E and D were belonged to "wear-out failure", and that the mean time between failures became shorter in order as indicated above. To insure longer lives of those parts, it would be necessary to change the design and the material and to upgrade operators mechanical technique of the mist and dust blower. The failure of the parts A, B and F was classified as "randomfailure", and they did not seem to be the "wear-out" at that time. The parts B and F was evaluated as "initial failure". Quality controls and operating tests by the producer. and the operational training for users should be strengthened so as to eliminate these failures. Were the failures only in the parts A, C, D, E, F and G, it could be said that the "reliability" of the mist and dust blower would fall to 10 percent in the second year, and 50 percent of the mist and dust blowers would fail in all parts A, C, D, E, F and G before the blower would have control insect and disease in 58.2 hectares. The use of the Weibull probability paper for analyzing failures of the mist and dust blowers was effective in that it analyzed failure in the relationship between strength of the parts and users actual circumstanoes.

• 한국임상수의학회지
• /
• 제27권6호
• /
• pp.740-745
• /
• 2010

동맥관개존증은 출생 후에도 폐동맥과 하행대동맥 사이에 동맥관이 지속적으로 열려 있는 선천성 심장질환이다. 동맥관개존증은 외과적인 결찰술로 폐쇄할 수 있지만, 다양한 도구를 이용한 동맥관개존증의 중재적 치료술은 비침습적인 치료과정과 시술 후 관리의 최소화의 이유로 빠르게 대체되고 있다. 소형품종에서의 중재적인 치료술은 동맥의 크기가 작기 때문에 혈관으로의 접근성이 주요한 문제점이 된다. 비록 경정맥을 이용한 정맥 접근법이 개발되었으나 이 기술은 동맥관에 폐색장치를 장착시키기 위해서 숙달된 기술이 필요하며, 폐색 장치 (색전 코일이나 혈관폐색장치)가 예기치 않게 잘못 장착될 위험성을 가지고 있다. 따라서, 우리는 이번 연구에서 소형품종 (체중3 kg미만)에서 대퇴동맥 접근을 통한 미니 혈관카테타를 이용한 변형된 코일 색전법을 개발하였다. 이러한 변형된 방법을 통하여 우리는 좌우 단락된 동맥관개존증을 가진 두마리의 소형품종 (말티즈)을 성공적으로 치료하였다.

• 한국식품영양학회지
• /
• 제9권4호
• /
• pp.452-458
• /
• 1996

호열균 B. stearothermophilus의 세포내 PPIase를 정제하여 Edman 법으로 N-말단 아미노산 배열을 결정하여 이를 바탕으로 합성한 올리고누클레오티드의 프리머를 이용하여, 서턴 분석하여 PPIase 유전자 약 3.0kb를 클로닝하였다.(pPI-40) PPI-40으로부터 PPIase N-말단 배열을 코드 하는 영역으로부터 합성한 프리머(A-1, B-2)를 이용하여, PCR법으로 PPIase N-말단을 코드 하는 유전자를 증폭하여, 염기배열을 경정한 후, 그 정보에 따라 유전 해석한 결과 PCR로 증폭된 단편(pSN-18)은 165염기로부터 형성된 55 아미노산잔기를 코드 하는 open reading frame (ORF)이 계속되고 있었고, Edman법으로 결정한 PPIase N-말단 아미노산 39 아미노산잔기가 완전히 일치하였다. 그리고, 이 ORF를 중심으로, 지금까지 클론화된 대장균의 PPIasea (cytoplasm)와 PPIase b(periplasm)의 아미노산 일차구조 해석으로부터 각각 58%(cytoplasm), 16%(periplasm)의 상동성을 나타냈다. PPIase 구조 유전자를 갖는 재조합플라스미드 pPI-40을 JM109로 형질전환하여 Lac 프로모터로 PPIase 단백질을 발현시켰다. 효소 분자량을 SDSPAGE로 확인한 결과 약 18kDa으로 호열균 B. stearothermophilus로부터 정제한 단백질 분자량과 동일하다. 면역억제(CsA, FK506)와의 화학적인 반응은 대장균의 PPIase와 동일하게, 면역억제와는 비감수성으로 나타났다.

• 한국미생물생명공학회:학술대회논문집
• /
• 한국미생물생명공학회 2001년도 Proceedings of 2001 International Symposium
• /
• pp.149-153
• /
• 2001

To investigate the mode of bactericidal action for antimicrobial peptide, pediocin, synthetic and mutant pediocins were prepared by direct chemical synthesis. Native pediocin was purified from Pedio-coccus acidilactici M and its conformational structure and bactericidal functions were analyzed and compared to synthetic pediocin. Schematic mode of pediocin actions, how pediocin binds on the target cell membrane, penetrates and makes tunnel are proposed. For these purposes, primary and secondary structures of pediocin was analyzed and disulfide bond assignment was also done. The pediocin purified from P. acidilactici M had high effective bactericidal ability against gram positive bacteria, especially Listeria monocytogenes and was very stable at extreme pHs and even at high temperatures such as autoclaving temperature (121$^{\circ}C$). Pediocin was consisted of 44 amino acids with four cysteines. Novel synthetic peptides were achieved by solid phase peptide synthesis(SPPS) method. To explain the function of cysteine in C-terminal region, mutant pediocin, Ped[C24A＋C44A], was synthesized and their structural and biological functions were analyzed. Second mutant pediocin, Ped[KllE], was prepared to explain the function of lysine at 11 of N-terminal part of pediocin, especially loop of $\beta$-sheet, and to predict the initial binding site of pediocin. The native and synthetic pediocins was showed random coil conformation by spectropolarimetry in moderate conditions. This conformation was observed in extreme conditions such as high temperature and low and high pHs, also. Circular dichroism(CD) data also showed the existence of $\beta$-turn structure in N-terminal part both native and synthetic pediocins. A structural model for pediocin predicts that 18 amino acids in the N-terminal part of the peptide assume a three-strand $\beta$-sheet conformation. This random coil in C-terminal part of pediocin was converted to folding structure, helix structure, in nonpolar solvents such as alcohol and TFE. The disulfide bond between $^{9}$ Cys and $^{14}$ Cys was concrete and inevitable, however, evidences of disulfide bond between $^{24}$ Cys and $^{44}$ Cys was not. Data of Ped[C24A＋C44A], pediocin mutant showed that $^{44}$ Cys was required during killing the target cells but not inevitable, since Ped[C24A＋C44A] still have bactericidal activity but much less than native pediocin. Another pediocin mutant, Ped[KllE], had still bactericidal activity, was controversial to propose that positive charge like as $^{11}$ Lys in loop or hinge in bacteriocin bound or helped to binding to microorganism with electrostatic interaction between cell membrane especially teichoic acid and positive amino acid nonspecifically. The conformation of pediocin among native, synthetic and mutant pediocins did not show big difference. The conformations between oxidized and reduced pediocin were almost similar regardless of native or synthetic.