• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.131.1-131
• /
• 2001

At the present time, multimedia chip, internet application, and network equipment is designed by using ARM core. Because it has a good debugging, software compiler and needed low power. We must process a data coding to send a multimedia data by real time. So need to connect software and hardware algorithm. In this research, We design interface for ARM9/AMBA based board using VHDL for these function implementation. The board is used the ARM company´s ARM940T for software function implementation and Xilinx company´s Virtex E2000 for hardware function algorithm. The various hardware algorithm (ME,ME,DCT) block for performance can be implemented on this system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 G
• /
• pp.2324-2326
• /
• 1998

Plant controller using VME bus is developed. This controller is a PLC designed to control up to 768 I/O units of POSFA PLC which has been developed already by POSCON. In many programming aspects, it adopts IEC 1131, international standard of PLC programming to keep up with international trends. A system software and a controller architecture including CPU board, DSP board and bus extension board are developed to support the IEC 1131, and becomes a base of E.I. controller being developed now.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1126-1128
• /
• 1992

The object of this study is the design of 3 phase on-board inverter. The key point in the inverter design is the selection of switching device, and its performance effects that of total system. In this study, six-step square wave inverter was designed using IGBT ( Insulated Gate Bipolar Transistor ) which has the advantages of MOSFET and bipolar transistor as switching device. The condition of being small and light which is the one of requirements for on-board equipment was accomplished by using IGBT module and optimising the snubber circuit, and the reliablity was increased. It is confirmed that the designed inverter satisfies the required performance through the performance and environment test.

• 원자력산업
• /
• 제13권11호통권129호
• /
• pp.14-21
• /
• 1993

• 한국축산식품학회지
• /
• 제32권1호
• /
• pp.62-67
• /
• 2012

This study calculated kinetic parameters of Escherichia coli O157:H7 and developed a probabilistic model to estimate growth probabilities of E. coli O157:H7 on polyethylene cutting boards as a function of temperature and time. The surfaces of polyethylene coupons ($3{\times}5$ cm) were inoculated with E. coli O157:H7 NCCP11142 at 4 Log $CFU/cm^2$. The coupons were stored at 13 to $35^{\circ}C$ for 12 h, and cell counts of E. coli O157:H7 were enumerated on McConkey II with sorbitol agar every 2 h. Kinetic parameters (maximum specific growth rate, Log $CFU/cm^2/h$; lag phase duration, h; lower asymptote, Log $CFU/cm^2$; upper asymptote, Log $CFU/cm^2$) were calculated with the modified Gompertz model. Of 56 combinations (temperature${\times}$time), the combinations that had ${\geq}$0.5 Log $CFU/cm^2$ of bacterial growth were designated with the value of 1, and the combinations that had increases of <0.5 Log $CFU/cm^2$ were given the value 0. These growth response data were fitted to the logistic regression to develop the model predicting probabilities of E. coli O157:H7 growth. Specific growth rate and growth data showed that E. coli O157:H7 cells were grown at $28-35^{\circ}C$, but there were no obvious growth of the pathogen below $25^{\circ}C$. Moreover, the developed probabilistic model showed acceptable performance to calculate growth probability of E. coli O157:H7. Therefore, the results should be useful in determining upper limits of working temperature and time, inhibiting E. coli O157:H7 growth on polyethylene cutting board.

• 보존과학연구
• /
• 통권7호
• /
• pp.56-86
• /
• 1986

The aim of this study is to scientifical conservation for the Sin An Ship. The test object is Pinus massoniana and Cunninghamia lanceolata of Sin An Ship's timber .Comtrast object is water soaked fresh wood of Pinus densiflora and Cryptomeria japonica The results were as follows.1. M. C is 280.9% in high degraded Planking board,237.5% in low degraded Planking board,158.6% in fresh wood of Pinus densiflora,222.6% in Bulkhead167.3% in fresh wood of Cryptomeria japonica2. Absorption rate of P.E.G is good at heating condition ($55∼60^{\circ}C$), especially in highdegraded wood.3. The dimensional change of wood during air drying is somewhat shrinked That's 7.22% in low degraded Planking board9.8% in high degraded Planking board and 4.11% in water soaked Pinus densiflora.4. The dimensional change of wood during P.E.G treatment is mostly swollen of wery small quantity.5. Salinity in desalinization tank showed below 50 p.p.m. It's indicate the end of desalinization treatment.6. Filtration with filter paper was possible up to 40% concentration only. Key words :M.c ; Moisture Content, Absorption rate, Dimension change, Salinity, Filtration.

• 수산해양기술연구
• /
• 제53권4호
• /
• pp.337-348
• /
• 2017

The tension of warp from trawler and sea-floor contact can generate tilt and wake turbulence around otter boards. Preliminary measurements of otter board tilt and 3-D flow velocity during bottom trawl operations were taken using a vector instrument to investigate the effects of wake turbulence at the trailing edge of the otter board. Tilt data (i.e., yaw, pitch, and roll) at 1 Hz and flow data (velocities in the towing, lateral, and vertical directions) at 16 Hz were analyzed to determine their periods and amplitudes using global wavelet and peak event analyses. The mean period (${\pm}standard$ deviation) of the tilt from the peak event analysis ($5{\pm}2s$) was longer or double than that of flow velocity ($3{\pm}2s$). The two periods also had a significant linear relationship. The turbulence rate of flow was 30-50% at the trailing edge and was closely related to roll deviation. The frequency of phase difference ratios (i.e., peak time differences between tilts and flow periods) was significantly different from random occurrence in two trials, possibly due to side tidal effects. However, in the other trials, flow peaks were random, as shown by the even peak times between tilts and flows. Future studies should focus on reducing tilt variation, wake turbulence, and bottom contact to stabilize otter board motion.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.49-52
• /
• 2008

The present study was to develop a dry PFB method similar to the existing gypsum board construction method in order to apply the existing wet PFB method that uses fire-resistant adhesive. It was found that the existing wet method can produce concrete compressive strength of 80MPa and fire resistance of 3 hours with 30mm PF boards. The goal of development in this study was fire resistance of 3 hours through dry construction of 15mm fire-resistant boards. 1. Improved PF board was prepared by adding inorganic fiber to existing board and using aggregate with grain size of 3mm or less. Molding was done at temperature higher than that for existing PF board molding. While wet curing is used for existing PF boards, this study used dry curing in order to enhance heat insulation performance. 2. According to the results of fire resistance test, when the dry PF method was applied, the temperature of the main reinforcing bar was 116℃ in 15mm, 103.8℃ in 20mm, and 94℃ in 25mm, and these results satisfied the current standards for fire resistance control presented by the Ministry of Land, Transport and Maritime Affairs. When a 3-hour fire resistance test was performed and the external properties of the specimen were examined, the outermost gypsum board hardly remained and internal PF board maintained its form without thermal strain.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.592-595
• /
• 2003

In this paper, we have designed a Home Networking System using an embedded linux board. The system based on the World-Wide-Web is composed of three parts - a Server, a Client and a Simulator. The Home Networking Server is built in an embedded board using an embedded linux kernel. A web-server and Home Networking Server Seryice Demon programming with a Jaya-Language is included in the board. Clients can connect to the server board using a web-browser in the desktop computer, PDA or any other machines which include a web-browser. For this purpose, we made the client program using a Java-Applet. So, the clients who connect to the server for the control of the applications, download the class-file and execute the client-program in the web-browser. So, the clients don't need any other programs to control the applications from a remote place. The size of server board is very small (86.3$\times$74mm), which makes it very useful not only for the Home-Networking-System but also in many other fields, e.g., embedded robot control system, etc. Using an embedded board instead of a desktop computer is good for a simple network environment and it occupies only a small space to make the system.

• 대한한의학회지
• /
• 제31권1호
• /
• pp.122-129
• /
• 2010

Objective: To investigate institutional review boards and approved clinical trials of Oriental medical hospitals in Korea Methods: We e-mailed 16 Oriental medical hospitals a survey consisting of questions that addressed two topics, institutional review boards and the clinical trials they approved. The first part included questions about whether each hospital had an institutional review board, that board's staffing and education, reviews, and expedited reviews. The clinical trials portion covered the number and types of approved clinical trials, treatment methods, whether an investigator or a sponsor initiated the trials, diseases, time frame, and clinical trial fee. Results: We received a response to our e-mail from 14 hospitals, all of which had an institutional review board. The average number of institutional review board members was 13.57. Of these Oriental medical hospitals, 70% and 49% said that they regularly educated their institutional review board staff and clinical trial, investigators, respectively. 79% of the hospitals claimed to conduct regular reviews, and 50% said that they did so monthly. The number of approved clinical trials increased sharply from 11 in 2005 to 102 in 2008. 68% of these clinical trials were randomized, and the most-used treatment methods were herbal medicine (35%) and acupuncture (29%). The most common target diseases were circulatory (19%), urinogenital (14%), and musculoskeletal (13%) disease. Conclusions: Despite the rapid increase in clinical research in oriental medical hospitals, many more efforts including raising IRB quality, varying research diseases and increasing clinical trials in the hospitals located in non-metropolitan area, should be made.