• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.15-16
• /
• 2010

We used Brewster's Law to examine the mechanism of liquid crystal (LC) alignment on an organic insulation layer when subjected to ion-beam irradiation. Brewster's Law implies that the maximum rate polarized rayon a slanted insulation layers on the substrate and it illustrates the dependence of polarization and themechanical structure on the ion beam irradiation process. The pretilt angle of nematic LCs on the organic insulation surface was about $1.13^{\circ}$ for an ion beam exposure of $45^{\circ}$ for 1 minute at 1800eV. This shows the dependence of LC alignment on the polarization ratio in a slanted organic insulation layer. We also discussed the electro-optical characteristic of twisted nematic (TN) LCD using ion beam irradiation on organic overcoat layer.

• Food Science of Animal Resources
• /
• v.30 no.1
• /
• pp.124-132
• /
• 2010

This study evaluated the effects of gamma ray and electron beam (E-beam) to improve the safety of spices for meat processing. The spices (garlic powder, curry powder, turmeric powder, black pepper, white pepper, oregano, parsley, laurel leaf powder, basil, and rosemary) were irradiated by gamma ray and E-beam at 0, 2, 4, 6, 8, and 10 kGy. Total bacterial populations were then enumerated on total plate count agar, and bacteria isolated from the samples were identified by polymerase chain reaction (PCR). In addition, $D_{10}$ values for Bacillus cereus and Staphylococcus aureus inoculated in spices was determined, and the Ames test was conducted for genotoxicity analysis. The contaminated total bacterial populations in spices ranged from 1.5 to 3.8 Log CFU/g, and most of identified bacteria were Bacillus spp., and Staphylococcus spp. However, the bacterial populations decreased below the detection limit (2 Log CFU/g) after irradiation at 4 kGy except for parsley, which required 6 kGy in gamma ray and 8 kGy in E-beam to decrease total bacterial populations below detection limit. $D_{10}$ values were also higher (p<0.05) in E-beam treated samples than gamma-ray treated samples. No genotoxicity was observed in both conditions with and without metabolic activation. These results indicate that gamma ray (>4 kGy and <6 kGy) could be more useful to improve food safety of meat processing spices compared to E-beam.

• Electrical & Electronic Materials
• /
• v.10 no.8
• /
• pp.756-762
• /
• 1997

In this paper the change of electrical properties of transformer oil due to electron beam irradiation is investigated. The specimens are produced with a some different dose of 0.5[Mrad], 1[Mrad] and 2[Mard] except for original specimen. The physical properties of each specimen is analyzed by using the FT-IR spectrum. So it is confirmed that carbonyl groups are increased according to the increase of electron beam dose and also that the nitric compounds are disappeared. The magnitude of dielectric dissipation factor appears maximum value by the contribution of dipoles and ions in the low temperature low voltage region and it is stable due to the saturation of carriers in the high temperature high voltage region in the electric conduction characteristics. Volume resistivity is also measured one of original specimen is larger than irradiated specimen.

• The Plant Pathology Journal
• /
• v.31 no.2
• /
• pp.176-180
• /
• 2015

Postharvest diseases cause losses in a wide variety of crops around the world. Irradiation, a useful nonchemical approach, has been used as an alternative treatment for fungicide to control plant fungal pathogens. For a preliminary study, ionizing radiations (gamma, X-ray, or e-beam irradiation) were evaluated for their antifungal activity against Botrytis cinerea, Penicillium expansum, and Rhizopus stolonifer through mycelial growth, spore germination, and morphological analysis under various conditions. Different fungi exhibited different radiosensitivity. The inhibition of fungal growth showed in a dose-dependent manner. Three fungal pathogens have greater sensitivity to the e-beam treatment compared to gamma or X-ray irradiations. The inactivation of individual fungal-viability to different irradiations can be considered between 3-4 kGy for B. cinerea and 1-2 kGy for P. expansum and R. stolonifer based on the radiosensitive and radio-resistant species, respectively. These preliminary data will provide critical information to control postharvest diseases through radiation.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.1
• /
• pp.31-36
• /
• 2011

$TiO_2$ films were deposited on a glass substrate with RF magnetron sputtering and then surface of $TiO_2$ films were electron beam irradiated in a vacuum condition to investigate the effect of electron bombardment on the thin film crystallization, surface roughness and gas sensitivity for hydrogen. $TiO_2$ films that electron beam irradiated at 450eV were amorphous phase, while the films irradiated at 900 eV show the anatase (101) diffraction peak in XRD pattern. AFM measurements show that the roughness is depend on the electron irradiation energy. As increase the hydrogen gas concentration and operation temperature, the gas sensitivity of $TiO_2$ and $TiO_2$/ZnO films is increased proportionally and $TiO_2$ films that electron beam irradiated at 900 eV show the higher sensitivity than the films were irradiated at 450eV. From the XRD pattern and AFM observation, it is supposed that the crystallization and rough surface promote the hydrogen gas sensitivity of $TiO_2$ films.

• Applied Microscopy
• /
• v.51
• /
• pp.1.1-1.2
• /
• 2021

We demonstrate a fabrication of an atomically controlled single-crystal heart-shaped nanostructure using a convergent electron beam in a scanning transmission electron microscope. The delicately controlled e-beam enable epitaxial crystallization of perovskite oxide LaAlO₃ grown out of the relative conductive interface (i.e. 2 dimensional electron gas) between amorphous LaAlO₃/crystalline SrTiO₃.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.7
• /
• pp.49-54
• /
• 2012

This study focuses on the decomposition of pentachlorophenol(PCP) by an electron beam (E-beam) process. To attain this objective, we investigated the reactive species generated from E-beam process during irradiation (reaction time 0.6 s) and G-values of PCP decomposition and effects of pH and $H_2O_2$ as an additive. The effect of pH values was independent on the decomposition of PCP. However, during E-beam irradiation a scavenging effect of added $H_2O_2$ (> 1mM) for the decomposition of PCP was shown, which was supported by the decreased amounts of $Cl^-$ produced by the decomposition of PCP. Meanwhile, oxalic acid and unidentified organic chlorine compounds as by-products were increased by the addition of $H_2O_2$. Thus, in order to enhance the efficiency of PCP decomposition, the E-beam process has to consider a proper concentration of $H_2O_2$ as a well-known source of strong oxidant hydroxyl radical.

• Applied Chemistry for Engineering
• /
• v.28 no.3
• /
• pp.299-305
• /
• 2017

Activated carbon fibers (ACFs) were surface-modified by electron beam (E-beam) irradiation and used as a gas sensor electrode to investigate the effect of E-beam on nitric oxide (NO) gas sensing performance. XPS results showed that the oxygen component of ACFs surface treated by E-beam decreased and $sp^2$ bonded carbon of ACFs surface increased. These results were attributed to the structural transformation of ACFs surface irradiated by E-beam. NO gas sensitivity of the electrode composed of ACFs irradiated by100 kGy increased from about 4% to 8%, and the response time was also meaningfully enhanced from 360 s to 120 s. This is due to the fact that the $sp^2$ carbon bond increased by E-beam irradiation of activated carbon fibers, which significantly affects the resistance change of the electrode in NO gas sensing.

• Composites Research
• /
• v.29 no.4
• /
• pp.156-160
• /
• 2016

Glassy carbon can be utilized in a variety of harsh environment due to exceptional thermal stability and chemically impermeability along with scalability and low electrical resistance. In this work, we studied effects of electron(e)-beam irradiation on thermoelectric properties of the glassy carbon film. E-beam irradiation triggered local crystallization and/or amorphization of glassy carbon thin films, which was determined by a Raman spectroscopy. The structural change by e-beam irradiation leads to the change in the doping level of the glassy carbon, which can be inferred from the change of a Seebeck coefficient and an electric conductivity. The optimal power factor we obtained for the irradiated glassy carbon film was ~200% higher than that of the non-irradiated sample.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.98-98
• /
• 2010

Ion beam irradiation has been extensively used for surface modification of polymers, glassy metals and amorphous and crystalline materials at micron and submicron scales. The surface structures created by exposure to an ion beam range from dots, steps and one-dimensional straight wrinkles to highly complex hierarchical undulations and ripples. In general, the morphology of these nanoscale features can be selected by controlling the ion beam parameters (e.g. fluence and acceleration voltage), making ion beam irradiation a promising method for the surface engineering of materials. In the work, we presented that ion beam irradiation results in creation of a peculiar nanoscale dimple-like structure on the surface of polyimide - a common polymer in electronics, large scale structures, automobile industry, and biomedical applications. The role of broad Ar ion beam on the morphology of the structural features was investigated and insights into the mechanisms of formation of these nanoscale features were provided. Moreover, a systematic experimental study was performed to quantify the role of ion beam treatment time, and thus the morphology, on the coefficient of friction of polyimide surfaces covered by nanostructure using a tribo-experiment. Nano-indentation experiment were performed on the ion beam treated surfaces which shows that the hardness as well as the elastic modulus of the polyimide surface increased with increase of Ar ion beam treatment time. The increased of hardness of polyimide have been explained in terms of surface structure as well as morphology changes induced by Ar ion beam treatment.