• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.2
• /
• pp.78-84
• /
• 2016

This paper is focused on the measurement and analysis of an atmospheric electric field which is caused by thunderclouds. The electric field due to thunderclouds changes very slowly. For this reason, the extremely low frequency E-field sensor needs to be used for measuring the atmospheric electric field strength. The balloon-carried E-field sensor system with the time constant of 1sec was designed and fabricated. The electric field sensor consists of $100mm{\times}100mm$ copper plate, active integrator, high pass and low pass filters and batteries. The measurements of atmospheric electric fields were made by the balloon-carried E-field sensor and radiosonde, which sends the data back to ground in real time. From the calibration experiments, the response sensitivity of the E-field sensor was 0.154mV/kV/m in the frequency range of less than 1kHz. As a result from the actual experiment of the atmospheric electric field, the electric field signals were observed from the altitude of about 2.5km. Also, as the altitude was increased, the detected electric field wave oscillated with the fluctuation of sensing plate. The proposed method seems suitable for measurements of atmospheric electric fields, because it is inexpensive, simple to use and launch.

• Journal of the Korean Magnetics Society
• /
• v.23 no.6
• /
• pp.205-208
• /
• 2013

The width dependence of Delta E has been studied by impedance resonance method in Fe-rich amorphous ribbon of as received state. It can be explained by single domain model include effective magnetic field $H_{eff}$ and demagnetization factor $N_d$. Wider width ribbon's effective is smaller than narrow it. Young's modulus also smaller than narrow width. These result well agreement in calculation. It has been also studied that linear magnetic field sensor using width dependence of Delta E under the field range 0 Oe~80 Oe. The sensitivity of the sensor was found to be 95 Hz/Oe.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.3
• /
• pp.306-311
• /
• 2007

The transient fields generated during switching operations in a Gas Insulated Substation (GIS) are associated with high frequency components in the order of few tens of MHz. These transient fields leak into the external environment of the gas-insulated equipment and can interfere with the nearby electronics. Measurements of the transient fields are thus required to characterise the interference caused by switching phenomena in such substations. In view of the above, E-field emission measurement during a switching operation has been carried out for a 245 kV GIS model, using a resonant dipole antenna and D-dot sensor. The characteristics of the E-fields i.e., frequency spectra and their levels have been analysed and are reported in the paper. Suitability of the measurements has been confirmed by comparing frequency spectra of the measured and computed transient fields.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.6 no.2
• /
• pp.47-53
• /
• 2010

In this research project, development of methodology to measure the thickness of pipes in the wide range using magnetic field. The magnetic field spreading in the sensor and the plate was modeled in the cases of the various thicknesses in plate. Based on the analysis, sensors were designed, manufactured and tested to optimize the specifications of the sensor. The sensor can be used in high temperature through calibration. And the uncertainty of the sensor was estimated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.5
• /
• pp.459-465
• /
• 2022

This paper reports a method to use a wireless sensor network deployed in the field to real-time monitor soil moisture, warning when the moisture level reaches a specific value, and wirelessly controlling an additional device (LED or water supply system, etc.). In addition, we report all processes related to wireless irrigation system, including field deployment of sensors, real-time monitoring using a smartphone, data calibration, and control of additional devices deployed in the field by smartphone. A commercially available open-source Internet of Things (IoT) platform, NodeMCU, was used, which was combined with a 9V battery, LED and soil humidity sensor to be integrated into a portable prototype. The IoT-based soil humidity sensor prototype deployed in the field was installed next to a tree for on-site demonstration for the measurement of soil humidity in real-time for about 30 hours, and the measured data was successfully transmitted to a smartphone via Wifi. The measurement data were automatically transmitted via e-mail in the form of a text file, stored on the web, followed by analyses and calibrations. The user can check the humidity of the soil real-time through a personal smartphone. When the humidity of a soil reached a specific value, an additional device, an LED device, placed in the field was successfully controlled through the smartphone. This LED can be easily replaced by other electronic devices such as water supplies, which can also be controlled by smartphones. These results show that farmers can not only monitor the condition of the field real-time through a sensor monitoring system manufactured simply at a low cost but also control additional devices such as irrigation facilities from a distance, thereby reducing unnecessary energy consumption and helping improve agricultural productivity.

• Journal of computational fluids engineering
• /
• v.10 no.1
• /
• pp.73-79
• /
• 2005

Micro sensor is very useful for flow measurements in a number of engineering applications. Especially, it is necessary for the development of MEMS. This paper presents the 3D numerical simulation of flows around a micro flow sensor, which is mounted on a flat plate. The effects of the sensor configuration (i.e. bottom gap) and the Reynolds number on the flow field are numerically investigated. The numerical results indicate that the bottom gap clearly affects the flow fields over the top surface of the sensor. The Reynolds numbers also show a significant influence on the flow nature, especially on the recirculation zone at downstream of the sensor. The present results illustrate a certain improvement on the flow field for the sensor installed at O.5mm above the wall with four pillars, comparing with that directly mounted on the wall.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.10
• /
• pp.1051-1056
• /
• 2014

In this paper, we introduce an intelligent robotic arc welding system which exploits sensors like as LVS (Laser Vision Sensor), Hall effect sensor, voltmeter and so on. The use of industrial robot is saturated because of its own limitation, and one of the major limitations is that industrial robot cannot recognize the environment. Lately, sensor-based environmental awareness research of the industrial robot is performed actively to overcome such limitation, and it can expand application field and improve productivity. We classify the sensor-based intelligent arc welding robot system by the goal and the sensing data. The goals can be categorized into detection of a welding start point, tracking of a welding line and correction of a torch deformation. The Sensing data can be categorized into welding data (i.e. current, voltage and short circuit detection) and displacement data (i.e. distance, position). This paper covers not only the explanation of the each category but also its advantage and limitation.

• Carbon letters
• /
• v.12 no.3
• /
• pp.162-166
• /
• 2011

Conducting polymer-coated multiwalled carbon nanotubes (MWCNTs) were prepared by template polymerization in order to enhance their gas sensitivity. This investigation of the conducting polymer phases that formed on the surface of the MWCNTs is based on field-emission scanning electron microscopy images. The thermal stability of the conducting polymer-coated MWCNTs was significantly improved by the high thermal stability of MWCNTs. The synergistic effects of the conducting polymer-coated MWCNTs improve the gas-sensing properties. MWCNTs coated with polyaniline uniformly show outstanding improvement in gas sensitivity to $NH_3$ due to the synergistic combination of efficient adsorption of $NH_3$ gas and variation in the conduction of electrons.

• 한국정보통신설비학회:학술대회논문집
• /
• 2008.08a
• /
• pp.473-477
• /
• 2008

In this paper, we introduce the positioning methods using the grid sensor network. The basic operational principle of grid sensor network can be the wireless communication using the sensor node attached on the objects. Sink node receives the environmental information (e.g., temperature, humidity and so on), and transmits the information to the core database. Since the grid sensor network basically uses wireless communication, it is necessary to observe the place where grid sensor nodes to be installed. In this sense, we carried out the practical measurement on the wireless propagation in an applicable field. In addition, link budget study and SNR estimation works were done in accordance with the results from the measurement.

• Journal of Sensor Science and Technology
• /
• v.13 no.6
• /
• pp.454-461
• /
• 2004

We have designed a portable electronic nose (e-nose) system using an array of commercial gas sensors and personal digital assistants (PDA) for the recognition and analysis of volatile organic compounds (VOC) in the field. Field screening of pollutants has been a target of instrumental development during the past years. A portable e-nose system was advantageous to localize the special extent of a pollution or to find pollutants source. The employment of PDA improved the user-interface and data transfer by Internet from on-site to remote computer. We adapted the Lavenberg-Marquardt algorithm based on the back-propagation and proposed the method that could predict the concentration levels of VOC gases after classification by separating neural network into two parts.