• 한국산학기술학회논문지
• /
• 제14권7호
• /
• pp.3158-3163
• /
• 2013

본 연구에서는 회전속도, 브레이크 압력 제어가 가능한 브레이크 다이나모메타를 제작하여 스퀼 소음 실험을 실시하였다. 브레이크 패드는 각각 $34^{\circ}$, $30^{\circ}$, $26^{\circ}$로 가공하여 패드 각도에 따른 스퀼 발생 조건과 음의 기울기 발생에 따른 스퀼 연관성을 연구 하였다. 각도에 따라 특정한 회전속도와 브레이크 압력에서 스퀼이 발생하였으며, 각도에 상관없이 하모닉 성분을 가지는 특정 주파수 소음을 발견하였다. 햄머링 테스트 및 유한요소해석을 통해서 특정 주파수는 In-plane모드 성격을 갖고 있으며, 패드 각도에 둔감한 모드임을 밝혀냈다.

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.1-7
• /
• 2014

A variable displacement vane pump is possible to improve the fuel economy by varying the pump capacity with a vane mechanism according to the engine operating speed range and reducing its driving torque. In general the experimental evaluation of the vane pump for the transmission has been performed mainly not with the vehicle or dynamometer test rig but with component test rig due to the implementation and safety problems. In this paper, in order to evaluate the performance of the developed vane pump as well as the compatibility with other rotary and hydraulic components of the target transmission, the transmission dynamometer based test rig is implemented where the developed pump is built into it and then the variable pump capacity and effect of power reduction are investigated experimentally.

• 융복합기술연구소 논문집
• /
• 제4권2호
• /
• pp.67-70
• /
• 2014

Recently EU has been recognized that there is a difference of emission quantity between emission certification test mode and real-road driving test. Accordingly the European Commission is currently preparing to require real-road testing as part of the passenger car type-approval process in the EU. vehicle manufacturers from 2017 are expected to test new vehicles not only under laboratory conditions but also on the real-road, using PEMS equipment. Therefore the purpose of this study is to analyze the emission and Fuel Economy of CVS-75 mode test using chassis dynamometer and RDE test using PEMS equipment by PHEV passenger car.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권6호
• /
• pp.776-782
• /
• 2003

This paper describes a newly developed double squirrel cage induction motor in which the rotor is located outside the stator. The outside rotor type brushless dc motor has been used for VTR's head drum and PC's cooling fan, but this kind of induction motor has not been developed yet. The parameters of outside rotor type induction motor were measured from the locked rotor test and no load test. It is possible to determine the parameters which are presented in the steady-state equivalent-circuit of the outside rotor type induction motor. Load test of induction motor was carried out using a dynamometer. For the characteristics of torque, efficiency, power factor and output. the developed double squirrel cage induction motor is compared with the ordinary induction motor It is believed that the results of this paper can be used for the development of the outside rotor type induction motor.

• 대한기계학회논문집A
• /
• 제38권1호
• /
• pp.37-44
• /
• 2014

본 연구에서는 전기이륜차의 1회충전주행거리를 알아보기 위해 도로 주행시험과 차대동력계(Chassis Dynamometer) 주행시험을 하였다. 도로주행시험은 대전시(Daejeon Metropolitan City)의 도로 중 대표적인 3가지 루트에서 주행시험을 하였다. 차대동력계를 이용한 CVS-40모드 주행시험의 경우 도로 부하조건을 다양하게 설정하여 CVS-40 모드주행을 실시하였다. 본 연구를 통하여 도로에서의 전기이륜차의 1회 충전주행거리(Per-Charge Range Testing)를 확인하고, 차대동력계 도로부하 설정방법에 따른 주행거리 및 에너지소비효율을 측정하였다. 이를 통해 실도로 주행시험과 차대동력계 주행시험을 비교하여, 차대동력계 실험에서도 전기이륜차 1회충전주행거리시험이 실도로에서의 주행조건과 근접한 결과를 갖는 도로부하 설정에 대해 연구하였다.

• 한국기계가공학회지
• /
• 제18권9호
• /
• pp.72-80
• /
• 2019

In this task, the tool dynamometer design and manufacture, and the Ansys S/W structural analysis program for tool attachment that satisfies the cutting force measurement requirements of the tool dynamometer system are used to determine the cutting force generated by metal cutting using 3-axis static structural analysis and the LabVIEW system. The cutting power in a cutting process using a milling tool for processing metals provides useful information for understanding the processing, optimization, tool status monitoring, and tool design. Thus, various methods of measuring cutting power have been proposed. The device consists of a strain-gauge-based sensor fitted to a new design force sensing element, which is then placed in a force reduction. The force-sensing element is designed as a symmetrical cross beam with four arms of a rectangular parallel line. Furthermore, data duplication is eliminated by the appropriate setting the strain gauge attachment position and the construction of a suitable Wheatstone full-bridge circuit. This device is intended for use with rotating spindles such as milling tools. Verification and machining tests were performed to determine the static and dynamic characteristics of the tool dynamometer. The verification tests were performed by analyzing the difference between strain data measured by weight and that derived by theoretical calculations. Processing test was performed by attaching a tool dynamometer to the MCT to analyze data generated by the measuring equipment during machining. To maintain high productivity and precision, the system monitors and suppresses process disturbances such as chatter vibration, imbalances, overload, collision, forced vibration due to tool failure, and excessive tool wear; additionally, a tool dynamometer with a high signal-to-noise ratio is provided.

• 대한조선학회논문집
• /
• 제58권6호
• /
• pp.391-399
• /
• 2021

In order to investigate force and cavitation characteristics for the flat & twisted rudders in the Large Cavitation Tunnel (LCT), the rudder dynamometer was designed and manufactured. The measuring capacities of lift, drag and moment are ±1000 N, ±2000 N, and ±150 N-m, respectively. The present dynamometer uses the actuator with a harmonic drive to control the rudder angle without backlash. As the target ship is a military ship with twin shaft, each dynamometer was installed above the port & starboard rudders. After the installation of the model ship with all appendages, the model test composed of rudder force measurement and cavitation observation was conducted for the existing flat rudder & the designed twisted rudder. While the flat rudder showed the big difference of lift & moment between port & starboard, the twisted rudder presented a similar trend. The cavitation of the twisted rudder showed better characteristics than that of the flat rudder. Another set of model tests were conducted to investigate rudder performance by the change of the design propeller. There was little difference in rudder performance for the design propellers with slight geometric change. Through the model test, the characteristics of the flat & twisted rudders were grasped. On the basis of the present study, it is thought that the rudder with better performance would be developed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.247-249
• /
• 2007

Urban dynamometer driving schedule(FTP-75 mode) plays very significant role on automotive emission test, due to reference point. The overall system energy efficiency of a HEV(Hybrid Electric Vehicle) is highly dependent on the energy management strategy employed. An energy source is the heart of a HEV. In order to applicable to a vehicle component, it must be need to real world test result. But, the present state of things have numerous problems. In this paper, be studied performed based on HEV simulation software in virtual world and chassis dynamometer test in real world and the result make a comparative. Toyota Prius vehicle was adapted as a modeling and real testing to evaluate the hybrid components and energy balancing management. The point at issue is voltage and current analysis for HEV battery SOC(State of Charge), and verification for energy.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.35-42
• /
• 2001

The diesel engine exhaust gas is know as one of the causes to produce photochemical smog, which causes damage on environmental. However, due to the high thermal efficiency and low carbon dioxide emission, the usage of a diesel engine is prevailed. In this study, the DC non-thermal plasma technology used to the particulate matter (PM) aftertreatment. The exhaust gas characteristics and energy density were investigated on the dynamometer test bed and chassis dynamometer with CVS-75 mode in a passenger diesel car. It was reported that the smoke removal efficiency has around the 70% in the dynamometer test with 80W energy consumption and the PM removal efficiency has the 68% in the real car test. The NOx also reduced the 20% according to electrode type respectively. Considering these results, plasma technology is one of the ways to simultaneously removing method the particulate matter (PM) and NOx.

• 대한조선학회논문집
• /
• 제61권3호
• /
• pp.161-169
• /
• 2024

In order to investigate cavitation performance for the azimuth thruster in Large Cavitation Tunnel (LCT), the cavitation test apparatus was designed and manufactured. Generally the model scale is determined by the pod dynamometer with about 70mm diameter. Recently as ships with azimuth thruster have become bigger, the problem of the model ship installation was occurred. The model ship with pod dynamometer couldn't be installed in the LCT test section. The cavitation test apparatus and technique which can conduct the cavitation test without pod dynamometer were developed. The cavitation tests were conducted in torque identity method instead of thrust identity method. The target ship with azimuth thruster is 18K LNG bunkering vessel. As the full-scale ship test was conducted, the model cavitation tests were conducted at the same operating conditions. The fluctuating pressure levels of the full-scale ship were compared to those of the model tests. Another model cavitation test was conducted in the foreign institute and the cavitation observation results were compared to those of LCT. Through the comparison with the existing results, it is thought that the cavitation test for the azimuth thruster can be conducted in torque identity method.