• Proceedings of the KSR Conference
• /
• 2003.10a
• /
• pp.210-215
• /
• 2003

Korean High Speed Train (KHST) has been tested on high speed line in JungBu site since it was developed in 2002. The KHST figured 7 cars was modeled for dynamic simulation with Vampire program. and the data acquisition system was used to test successfully the on-line test for proving the dynamic performance of KHST. The comparison between test and simulation results for dynamic behavior of KHST was tried in this paper and it was very difficult because the environmental conditions and running conditions have an effect on the test results and these conditions are unable to be modeled for dynamic analysis. Also the parameters for data acquisition system for test are usually not same to simulation conditions. Therefor, in this paper the acceleration data after filtering with low pass filter below 1Hz were used to compare between test and simulation results because the low frequency range is useful to evaluate the dynamic performance for railway vehicle system, so as steady state curving acceleration. The results show that both are similar in low frequency range.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.103-108
• /
• 2013

This paper describes basic properties tests and non-rotating dynamic test for rotor blade, flexbeam, and torque tube of which bearingless rotor in helicopter consists. A basic properties test are bending and twist test to find the flap stiffness, lag stiffness, and twist stiffness of specimens. The purpose of dynamic test is to find natural frequencies and modes in non-rotating state. The test results are used to update the analysis model. The updated analysis results using rotorcraft comprehensive code match the tests quite well. The updated model input based on the tests will be utilized to analysis the conditions of rotating whirl tower test before the whirl test and will be compared with the whirl tower test results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.102-106
• /
• 2003

An experimental modal analysis and dynamic stiffness evaluation of a moving body structure of a high speed machining center are presented in this paper. The natural frequencies and corresponding modes, and dynamic compliance of a moving body structure of high speed machining center are investigated by using F.E.M., hydraulic exciter test, and impulse hammer test. The lowest three natural frequencies were found to be 56.6 Hz, 112.7 Hz, and 142.7 Hz by FEA respectively, while those were 55 Hz, 112 Hz, 131 Hz by experimental analysis. Furthermore, both computed and measured absolute dynamic compliances of the moving body structure in iso-direction showed good agreement especially at the first two mode frequencies. With our experimental data, the dynamic characteristics of the machining center can be exploited to get a new development of structural dynamic design and modification.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.304-309
• /
• 2000

Strain gage method is used to evaluate the mode I dynamic stress intensity factor of marging steel(18Ni) and titanium alloy(Ti-6A1-4V). To decide the best strain gage position on specimen, static fracture toughness test was performed. Then instrumented charpy impact test and dynamic tensile test was performed by using strain gage method for evlauating dynamic stress intensity factor. Strain gage signals on the crack tip region are used to calculate the stress intensity factors. It is found that strain gage method is more useful than method by using load which is obtained from impact tup to assess dynamic characteristics such as dynamic stress intensity factor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.348-357
• /
• 2006

Ground Vibration Tests (GVT) are needed on au new aircraft types and as part of certification. Its first objective is to verify models used for the calculation and prediction of the dynamic behavior of the structure. The main objectives of this paper are to introduce 'the integrated approach of dynamic testing for aerospace structure' in detail and 'The research projects in which LMS participated in aerospace structural dynamic area'

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.306-313
• /
• 2005

For seismic response analysis of rockfill dam, dynamic material properties, by field test, are needed. Density and elastic wave profiles have to be known to get an information of the material properties of structure. In this study, various field tests are applied to the example of rockfill dam to get an information of dynamic material properties and seismic safety is evaluated by seismic response analysis with the result of field tests.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.1 s.74
• /
• pp.69-74
• /
• 2007

This paper is concerned about the dynamic analysis of an underwater test miner, which operates on cohesive soil. The test miner consists of tracked vehicles and a pick-up device. The motion of the pick-up device, relative to the vehicle chassis, is controlled by two pairs of hydraulic cylinders. The test miner is modeled by means of commercial software. A terramechanics model of cohesive soft soil is implemented with the software and applied to a dynamic analysis of the test miner model. The dynamic responses of the test miner are studied with respect to four different types of terrain conditions.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.6
• /
• pp.327-335
• /
• 2004

Effect of spherodization of cementite on static and dynamic deformation behaviors of SCM415 steels was investigated in this study. Dynamic torsional test was conducted using torsional Kolsky bar with the strain rate of $1.6{\times}10^3/s$. Three type of specimens were used with different spherodization degree of cementite. Dynamic test results were analyzed comparing with static tensile results and microstructural changes. The obtained results are as follows; 1) All the specimens of static and dynamic tests showed a ductile fracture mode of dimple. Specimens of the dynamic test showed adiabatic shear bands on the beneath of fracture surface. 2) In static tensile test, decreased tensile strength and increased uniform and non-uniform elongations appeared as spherodization degree of cementite increased. 3) In dynamic torsional test, decreased shear strength and increased uniform elongation appeared as spherodization degree of cementite increased. 4) Due to the largest uniform elongation, superior cold forgeability at high speed is expected on high spherodization degree of cementite.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.826-831
• /
• 2002

In order to investigate the dynamic characteristics of real structure, many dynamic engineer had been interested in modal test however it is not easy to perform dynamic test of large structure because of many difficulties such as unsatisfied excitation force in global mode frequency range, measurement of dynamic force and so on. Therefore. new type vibration exciter with variable stiffness support system and dynamic force was developed to provide a improved experimental environment for a large and complex structure. The developed exciter improved from two viewpoint, dynamic performance and utility convenience. its characteristics was shown in this paper.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.853-858
• /
• 2003

The suitable estimation of the filter width in the dynamic eddy viscosity model were investigated in high Reynolds number channel flow. In this study, the improvement on matters by optimizing the test filter shape was attempted through the numerical experiment. The way that select optimum test filter width is recommended. Some test filters, one is based on a discrete representation of the top-hat filter and another are based on a high-order filtering operation, are evaluated in simulations of the turbulent channel flow at Reynolds number 1020, based on friction velocity and channel half width. It appears that the estimation of test filter width practically can decrease the dissipative nature of dynamic eddy viscosity model with explicit test filter. It shows that the value of the filter width ratio used in the dynamic procedure must match the properties of the test filter actually used in the calculation.