• Journal of IKEEE
• /
• v.28 no.3
• /
• pp.382-389
• /
• 2024

In this paper, a design of dynamic braking resistor for stationary mode of azimuth driving equipment (ADE) for multi-function radar (MFR) is presented. The ADE carries out missions which is the rotation mode for all directions and the stationary mode for tracing a subject with standstill. The ADE has to transfer the operation mode in demand time from rotation mode to stationary mode for precise target tracing. During the transition with deceleration, it may cause the fault of input power device due to back-electromotive force (back-EMF) of PMSM with generator mode. To protect the power device, a design of dynamic braking resistor is essential for consuming back-EMF. This paper presents the development of dynamic braking resistor for consuming back-EMF of ADE with deceleration mode. The validity and effect of the design is verified using simulation results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1359-1367
• /
• 2004

The purpose of this study is to predict the dynamic transmission error of the helical gear system. To do so, the equations of motion in the helical gear system which consists of motor, coupling, gear, torque sensor, and brake are derived. As the input parameters, the mass moment of inertia by a 3D CAD software and the equivalent stiffness of the bearings and shaft are calculated and the coupling stiffness is measured. The static transmission error as an excitation is calculated by in-house program. Dynamic transmission error is predicted by solving the equations of motion. Mode shape, the dynamic mesh force and the bearing force are also calculated. In this analysis, the relationship between the dynamic mesh force and the bearing force and mode shape behavior in gear mesh are checked. As a result, the magnitude of mesh force is highly related with the gear mesh behavior in mode shape. The finite element analysis is conducted to find out the natural frequency of gear system. The natural frequencies by finite element analysis have a good agreement with the results by equation of motion. Finally, dynamic transmission error is measured by the specially designed experiment and the results by equation of motion are validated.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.24 no.3
• /
• pp.129-139
• /
• 2020

An approximate analysis method is proposed to predict the dynamic amplification of shear forces in ordinary reinforced concrete shear walls as a preliminary study. First, a seismic design for three groups of ordinary reinforced concrete shear walls higher than 60 m was created on the basis of nonlinear dynamic analysis. Causes for the dynamic amplification effect of shear forces were investigated through a detailed evaluation of the nonlinear dynamic analysis result. A new modal combination rule was proposed on the basis of that observation, in which fundamental mode response and combined higher mode response were summed directly. The fundamental mode response was approximated by nonlinear static analysis result, while higher mode response was computed using response spectrum analysis for equivalent linear structural models with the effective stiffness based on the nonlinear dynamic analysis result. The proposed approximate analysis generally predicted vertical distribution of story shear and shear forces of individual walls from the nonlinear dynamic analysis with comparable accuracy.

• Journal of Mechanical Science and Technology
• /
• v.19 no.10
• /
• pp.1846-1855
• /
• 2005

This paper presents a new stochastic controller applied on the vibration control system under irregular disturbances based on the mode selection scheme. Measured displacement and frequency characteristics are simultaneously used in designing a mode selecting controller. This technique is validated by applying to the suppression problem of a flexible beam with randomly vibrated circumstances. The presented method, called Mode Selecting Stochastic Controller, uses the frequency measurement of the flexible system based on a Fast-Fourier transformation algorithm. This controller is constructed by combining mode selection method with previous known Stochastic Controller in real time: Numerical simulations and several experiments are conducted to validate the proposed method. The performance of the proposed method is compared with a stochastic controller developed recently. This method was improved compared with previous one.

• Journal of KSNVE
• /
• v.5 no.2
• /
• pp.215-224
• /
• 1995

In this paper, the three-dimensional finite element model is established to investigate the structural dynamic characteristics of rotor blade using a finite element analysis. Six natural frequencies and mode shapes are calculated by computer simulation. The first three flapping modal frequencies, the first two lead-lag modal frequencies, and the first feathering modal frequency are validated through comparison with the modal test results of the fixed rotor blade. The computer simulation results are found in good agreement with experimentally measured natural frequencies. The important results are obtained as follows: (1) Natural frequencies are changed due to the variation of rotational speed and fiber angle of rotor blade, (2) Weak coupling between flapping mode shape and lead-lag mode shape are detected, (3) Centrifugal force has more effect on flapping modal frequency than lead-lag modal frequency.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.9-17
• /
• 2017

Dynamic mode decomposition (DMD) method was applied for the further study of periodical characteristics of the unsteady shock-induced combustion. The case of Lehr's experiments was numerically simulated using 4 levels of grids. FFT result reveals that almost all the grid systems oscillate at frequencies around 430-435 kHz and the measureed one is around 425 kHz. To identify more resonant modes with low frequencies, DMD method is adopted for 4 grid systems. Several major frequencies are extracted and their damping coefficients are calculated at the same time, which is a quantification parameter for combustion stabilization.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.4
• /
• pp.191-197
• /
• 1998

This paper described the dynamic characteristics of 20-story apartment buildings from the results of full-scale measurements and analysis. The natural frequencies and mode shapes are quantified by measuring and analyzing ambient vibrations of the structure and compared with the results from dynamic analysis. Comparison with computed mode shapes and frequencies shows good agreement with the experimental results. It proved that it is important to estimate coupling beam and soil parameters through a comparison of the measured results with calculated results.

• Structural Engineering and Mechanics
• /
• v.13 no.5
• /
• pp.479-490
• /
• 2002

The structural dynamic optimization problem based on probability is studied. Considering the randomness of structural physical parameters and the given constraint values, we develop a dynamic optimization mathematical model of engineering structures with the probability constraints of frequency, forbidden frequency domain and the vibration mode. The sensitivity of structural dynamic characteristics based on probability is derived. Two examples illustrate that the optimization model and the method applied are rational and efficient.

• Journal of Sensor Science and Technology
• /
• v.26 no.2
• /
• pp.85-90
• /
• 2017

A wide dynamic range (WDR) CMOS image sensor (CIS) was developed with a specialized readout architecture for realizing high-sensitivity (HS) and low-sensitivity (LS) reading modes. The proposed pixel is basically a three-transistor (3T) active pixel sensor (APS) structure with an additional transistor. In the developed WDR CIS, only one mode between the HS mode for relatively weak light intensity and the LS mode for the strong light intensity is activated by an external controlling signal, and then the selected signal is read through each column-parallel readout circuit. The LS mode is implemented with the column capacitors and a feedback structure for adjusting column capacitor size. In particular, the feedback circuit makes it possible to change the column node capacitance automatically by using the incident light intensity. As a result, the proposed CIS achieved a wide dynamic range of 94 dB by synthesizing output signals from both modes. The prototype CIS is implemented with $0.18-{\mu}m$ 1-poly 6-metal (1P6M) standard CMOS technology, and the number of effective pixels is 176 (H) ${\times}$ 144 (V).

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.4
• /
• pp.100-106
• /
• 2009

The current tendency toward light weight and fast machines has lead to a need to suppress vibration of flexible dynamic systems. Input shaping is an efficient tool to eliminate transient and residual vibration caused by motion of these systems. This paper proposes a new formulation of the design method for multi-mode input shapers to eliminate residual vibration in flexible dynamic systems. The essence of the proposed method is to minimize the number of impulses to be n+1 for n-mode input shapers. This paper also suggests a solution procedure to solve the complex-valued nonlinear matrix equation for the input shapers. The proposed method is applied to two-mode input shapers. This paper discusses characteristics of several input shapers obtained under the same condition. Simulations and experiments show that the proposed method is very useful for designing multi-mode input shapers.