• Steel and Composite Structures
• /
• v.43 no.2
• /
• pp.153-164
• /
• 2022

In this study, a series of cyclic loading tests were performed on viscoelastic dampers (VED) composed of viscoelastic polymer composite material and thin steel plates to observe the variation of the mechanical properties under different loading conditions. A mathematical model was developed based on the Kelvin-Voigt and Bouc-Wen models to formulate the nonlinear force-displacement relationship of the viscoelastic damper. The accuracy of the proposed mathematical model was verified using the data obtained from the tests. The mathematical model was applied to analyze a reinforced concrete framed structure retrofitted with viscoelastic dampers. Nonlinear dynamic analysis results showed that the average maximum inter-story drift ratios of the retrofitted structure met the target limit state after installing the VED. In addition, both the maximum and residual displacements were significantly reduced after the installation of the VED.

• Tunnel and Underground Space
• /
• v.6 no.2
• /
• pp.144-156
• /
• 1996

The deformation behaviors under uniaxial compressive cyclic loading were investigated for fresh rocks and freeze-thaw cycled samples. The Pocheon granite which is one of the most popular building stone in Korea was selected for tests. 0.5 Hz and 50% of dynamic strength were used as test conditions for frequency and fatigue span, respectively. For freezethaw procedure, sample were frozen for 3 hours under the temperature of -2$0^{\circ}C$ and then followed 3 hours thawing under the temperature of +2$0^{\circ}C$. Twenty seven samples were used as untreated and seventy three for freeze-thaw samples. No failure occurred up to 15000 cycles at the stress level of 60% of dynamic strength, indicating that the lowest strees level for fatigue failure may be around 60% of dynamic strength. Permanent strain and damping capacity curves show that there were three stages when rock behaves like under creep. Young's moduli were increased and Possion's ratios were decreased with the increase of the number of cycles. Possion's ratios varied more rapidly than Young's moduli did with the increase of the number of cycles. This may represent that most microcracks developed by fatigue stress are parallel to the axis of loading. The deformation behavior of freeze-thaw cycled samples were almost the same as that of untreated samples. However, the result of freeze-thaw cycled samples showed lower regression constant, indicating that the physical durability of rock is much lowered because of cyclic temperature variation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.3
• /
• pp.139-149
• /
• 2002

An explicit direct time integration method based solution algorithm is proposed to predict dynamic postbuckling response of thin plates. Based on the von Karman's plate equations and Marquerre's shallow shell theory, a rectangular plate finite element is formulated and utilized in this study. The element formulation takes into account geometrical nonlinearity and initial deflection of plates. The solution algorithm employs the central difference method. Using the computer program developed by the authors, dynamic postbuckling behavior of elastic thin plates under impact loading is investigated by considering the time variation of load and load duration. The efficiency of the proposed solution algorithm is examined through illustrative numerical examples.

• Geotechnical Engineering
• /
• v.6 no.2
• /
• pp.5-20
• /
• 1990

In the seismic analysis of structures, where the dynamic soil-structure interaction (DSSI) is considred, earthquake input motions as well as dynamic soil properties are random in nature. To take into account the random nature of both the input motions and the dynamic soil properties systematically, a probabilistic analysis of the DSSI subjected to seismic loading is proposed in this paper, The complex response method formulized by the elastic half space theory, the random vibration theory, and the Rosenblueth's two-point estimate method are combined for the proposed probabilistic analysis. The conclusions drawn from this study are as follows ' 1) The uncertainty bands of the earthquake input motions proposed by Kanai-Tajimi as well as those of the dynamic properties are large the coefecients of variation of those parameters tinge from 0.4 to 0.6. 2) The uncertainties of the dynamic soil properties are more sensitive to the structural responses than those of the input motion parameters. 3) The effect of correlations between the input motion parameters and the dynamic soil properties is negligible.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.25-30
• /
• 2002

To reduce the vibration of a gear driving system, the modification of gear tooth from the orignal involute gear profile is usually done in gear manufacturers. The quantity of tooth modification has been decided on the basis of the interference between two gear teeth during gear meshing and the elastic deformation due to loading. However, the dynamic characteristics with tooth modification has to be investigated to avoid the instability to the variation of gear meshing stiffness and the nonlinearity due to gear backlash which results in sub- or super-harmonics in its responses. This research shows the dynamic characteristics with various tooth modifications in its type and quantity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.756-759
• /
• 2001

The purpose of this paper is to investigate the buckling and dynamic characteristics for the cylindrical shell under shear loading. To do this, a vibration model tests and analyses and static buckling analyses were performed for the reduced scale model of nuclear reactor vessel. From the results of vibration modal analysis with the pre-shear displacement loads, it is known that the beam vibration mode is not affected by the shear displacement, however shell vibration modes are significantly affected by it. As the pre-shear displacement increases to the critical buckling displacement, the 1st shell vibration frequency in greatly reduces and approaches to zero value.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.1
• /
• pp.34-38
• /
• 2010

An analytical solution procedure for the dynamic response of beams with variable properties is developed by using an asymptotic solution and the Green's function. This asymptotic closed form solution is derived for the transverse vibration of beams under the assumption of slowly varying properties, such as mass, cross-section, tension etc., along the beam length. However, this solution is still found to be very accurate even in the case of large variation, such as step change in cross-section, mass, and tension. Therefore, this derived asymptotic closed form solution and the Green's function can be easily applied to find dynamic responses for various kind of beam vibration problems.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.9
• /
• pp.688-693
• /
• 2003

To reduce the vibration of a gear driving system. the modification of gear tooth from the orignal involute gear profile is usually done in gear manufacturers. The quantity of tooth modification has been decided on the basis of the interference between two gear teeth during gear meshing and the elastic deformation due to loading. However. the dynamic characteristics with tooth modification has to be investigated to avoid the instability to the variation of gear meshing stiffness and the nonlinearity due to gear backlash which results in sub- or super-harmonics in its responses. This research shows the dynamic characteristics with various tooth modifications in its type and quantity.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.20-24
• /
• 1999

Grinding System is very difficult to examine closely wear phenomenon or dynamic characterastic because it is very complex and different from a general cutting system, Considering automatization and precision it is very important to examine closely grinding system. In this study grinding wheel surface is acquired by using computer vision system in order to explain wear and loading phenomenon. We investigate the relationship between wear and Fourier spectrum of acquired image and observe the entropy variation in the process of manufacturing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.12
• /
• pp.2972-2979
• /
• 2000

Dynamic characteristics of powder metal is very important to mechanical structures requiring high strength or endurance for impact loading. But owing to distinctive property of powder metal, that is relative, it has been investigated restrictively compared to static characteristics. The objectives of this study is to investigate dynamic characteristics of powder metal and compare it to a fully density material. To find the characteristics, an explicit finite element method is used for simulation of Split Hopkinson Pressure Bar experiment based on the stress wave propagation theory. We obtained a dynamic stress-strain relationship and dynamic behavior of powder metal, as well as the variation of material properties during dynamic deformation.