• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.797-802
• /
• 1998

Fiber reinforcement can significantly improve the properties of concrete. Particulary, toughness or energy-absorbing ability of fiber reinforced concrete is frequently higher than that of unreinforced concrete. Toughness is a measure of energy absorption capacity and used to characterized fiber reinforced concrete's ability to resist fracture when subjected to static, dynamic and impact loads. However, the current standard methods of characterizing the toughness of fiber reinforced concrete have proven to be some inadequate and problems and have caused a great deal of dissent and confusion. This study research some of the inadequate and problems with these toughness measurement methods and proposes the evaluation method for Fiber Reinforced Concrete toughness.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2001년도 춘계학술대회
• /
• pp.311-317
• /
• 2001

The notched Charpy and Izod impact tests are the most prevalent techniques used to characterize the effects of high impulse loads on ploymeric materials. An analysis method for rubber toughened PVC is suggested to evaluate critical strain energy release rates(Gc) from the Charpy impact energy measurements. An Instrumented Charpy Impact tester was used to extract ancillary information concerning fracture properties in addition to total fracture properties and maximum critical loads. The stress intensity factor Kd was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.339-344
• /
• 2000

In this study, the fracture phenomena of optical disks are discussed and then some recommendations are presented to prevent the fracture. The fracture occurs when disks have crack on the inner radius of the disks. Since the crack growth and the fracture result from the stress concentration on the tip of the crack, a measure should be taken to overcome the stress concentration. This problem can be resolved by the structural modification of a disk. This study proposes 3 types of improved optical disks, which are robust to the disk fracture due to the high spinning speed of a disk. The first type is a disk reinforced by wire rings, the second type is a disk added by texture fibers, and the third type is a rubber-coated disk.

• Macromolecular Research
• /
• 제17권8호
• /
• pp.585-590
• /
• 2009

The cure behaviors, dielectric characteristics and fracture toughness of diglycidylether of bisphenol-A (DGEBA)/poly(ethylene terephthalate) (PET) blend system were investigated. The degree of conversion for the DGEBA/PET blend system was measured using Fourier transform infrared (FTIR) spectroscopy. The cure kinetics were investigated by measuring the cure activation energies ($E_a$) with dynamic differential scanning calorimetry (DSC). The dielectric characteristic was examined by dielectric analysis (DEA). The mechanical properties were investigated by measuring the critical stress intensity factor ($K_{IC}$), critical strain energy release rate ($G_{IC}$), and impact strength test. As a result, DGEBAIPET was successfully blended. The Ea of the blend system was increased with increasing PET content to a maximum at 10 phr PET. The dielectric constant was decreased with increasing PET content. The mechanical properties of the blend system were also superior to those of the neat DGEBA. These results were attributed to the increased cross-linking density of the blend system, resulting from the interaction between the epoxy group of DGEBA and the carboxyl group of PET.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제23회 추계학술대회 논문집
• /
• pp.223-226
• /
• 2004

본 연구는 램제트 돔 포트 커버용 글라스 세라믹의 기계적 특성, 정적 및 동적 파괴인성을 평가하기 위해 수행하였다. 램제트 추진기관의 돔 포트 커버의 재료로 MACOR 글라스 세라믹 9658을 선정하였으며, 취성재료인 글라스 세라믹의 파괴인성을 측정하기 위해 노치시편에 대한 정적 및 동적 파괴인성시험을 수행하였다.

• 한국세라믹학회지
• /
• 제42권8호
• /
• pp.537-541
• /
• 2005

Silicon nitride is one of the most successful engineering ceramics, owing to a favorable combination of properties, including high strength, high hardness, low thermal expansion coefficient, and high fracture toughness. However, the impact damage behavior of $Si_3N_4$ ceramics has not been widely characterized. In this study, sphere and explosive indentations were used to characterize the static and dynamic damage behavior of $Si_3N_4$ ceramics with different microstructures. Three grades of $Si_3N_4$ with different grain size and shape, fine-equiaxed, medium, and coarse-elongated, were prepared. In order to observe the subsurface damaged zone, a bonded-interface technique was adopted. Subsurface damage evolution of the specimens was then characterized extensively using optical and electron microscopy. It was found that the damage response depends strongly on the microstructure of the ceramics, particularly on the glassy grain boundary phase. In the case of static indentation, examination of subsurface damage revealed competition between brittle and ductile damage modes. In contrast to static indentation results, dynamic indentation induces a massive subsurface yield zone that contains severe micro-failures. In this study, it is suggested that the weak glassy grain boundary phase plays an important role in the resistance to dynamic fracture.

• Nuclear Engineering and Technology
• /
• 제55권12호
• /
• pp.4647-4658
• /
• 2023

In this paper, elastic-plastic fracture mechanics analysis is performed to determine the critical crack sizes of the multipurpose canister (MPC) manufactured using austenitic stainless steel under dynamic loading conditions that simulate drop accidents. Firstly, dynamic finite element (FE) analysis is performed using Abaqus v.2018 with the KORAD (Korea Radioactive Waste Agency)-21 model under two drop accident conditions. Through the FE analysis, critical locations and through-thickness stress distributions in the MPC are identified, where the maximum plastic strain occurs during impact loadings. Then, the evaluation using the failure assessment diagram (FAD) is performed by postulating an external surface crack at the critical location to determine the critical crack depth. It is found that, for the drop cases considered in this paper, the principal failure mechanism for the circumferential surface crack is found to be the plastic collapse due to dominant high bending axial stress in the thickness. For axial cracks, the plastic collapse is also the dominant failure mechanism due to high membrane hoop stress, followed by the ductile tearing analysis. When incorporating the strain rate effect on yield strength and fracture toughness, the critical crack depth increases from 10 to 20%.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권1호
• /
• pp.47-54
• /
• 1988

TMCP steel manufactured by controlled rolling followed by accelerated cooling process is known to have extra-ordinary mechanical properties such as tensile strength and toughness. However, there is much uncertainty about the fatigue fracture characteristics of this steel. In this paper, the fatigue fracture behaviour of the TMCP steel in base metal and weldment were inspected through the Dynamic Implant test method. Those results were quantitavely compared with those of the ordinary normalized steel of same strength level. Moreover, the effect of the diffusible hydrogen included in the welded part on the fatigue fracture behaviour were made clear. As the experimental results, the fatigue fracture characteristics of the TMCP steel in case of base metal proved out to be superior to that of the normalized steel. However, the TMCP steel weldment including the diffusible hydrogen appeared to have inferior fatigue characteristics compared with the same conditioned normalized steel weldment.

• 한국정밀공학회지
• /
• 제12권8호
• /
• pp.147-155
• /
• 1995

Recent experimental studies have been shown that strain gages can be employed to determine either static or dynamic stress intensity factors $K_{I}$ wiht relatively simple experiments. However, it does not usually provide a reliable value of stress intensity factor because of local yielding and limited regions for strain gage placement at the vicinity of the crack tip. This paper attempted to define a valid region and to indicate procedures for locating and orienting the strain gage to determine static toughness $K_{Is}$ accurately form one strain gage readings with respect to varying loadings. The strain gage methods was used for compact tension specimens made of Polycarbonate and PMMA(polymethyl methacrylate). Series expansions of the static and dynamic strain fields are applied. Strain gage orientation and location are then studied to optimize the strain response. Especially, in the dynamic experiment, the specimen employed is an oversized Charpy V-notch specimen which has been modified to provide significant constraint with a large elevation of the flow stress. The impact behavior of the specimen is monitored by placing strain gage near the crack tip. The dynamic toughness $K_{Id}$ is determined from the strain time traces of this gage.e.

• Nuclear Engineering and Technology
• /
• 제21권3호
• /
• pp.165-170
• /
• 1989

준 동적 파괴가 일어나는 변형율속도 조건에서 A533B-1 원자로 압력용기강의 파괴인성 및 파괴저항특성에 미치는 변형율속도의 영향을 균열선단의 강 소성역 관찰 및 파면의 미세거칠기측정을 통해 연구하였다. 1/2T-CT 파괴시편에서 약 1.5mm 이하의 균열진전에 대해서는 소성일로 부터 구한 J와 수정 J가 거의 일치하였다. 파면의 미세거칠기로부터 구한 국부 변형율은 1.8-2.0 정도의 값을 나타내어 거시적으로 측정된 값보다 높은 값을 보여주었다. 이들 방법은 모두 변형율속도가 증가함에 따라 파괴인성은 증가하나 tearing modulus는 큰 변화가 없음을 보여주었다.