• 한국지반공학회지:지반
• /
• 제6권3호
• /
• pp.41-52
• /
• 1990

To investigate the liquefaction potential of sands, a series of untrained cyclic triaxial compression tests is carried out on the samples of Ottawa, Joomoonjin, Hn river and Hongseung sands. The constitutive equations of sands are derived to explain the mechanical behavior of sands under cyclic stresses, and are applicable to liquefaction analysis. The following results are obtainded in this study. 1. Sands with the lower confining pressure or relative density are to be easily liquefied, and when the amplitude of cyclic stress are large, liquefaction takes places over only a few cycles. 2. Stress ratio, porewater pressure ratio and cyclic shear strains are to be good criteria to evaluate liquefaction potential of sands. 3. Hongseung sands which contains some silty clay shows higher dynamic properties than other sands. 4. The dynamic behaviors of undisturbed Hongseung sand are about same as those of dense sands. It is noted that undisturbed Hongseung sand shows higher liquefaction potential than the samples made by pluviation under same relative density, 5. The constitutive equations of soils under cyclic loads are developed based on the theory of elasto-plasticity, logarithmic stress-strain rela'tionship, non-associated flow rule and the concept of the boundary surface. The derived equations is applicable to predict the behavior of sands under cyclic loads and liquefaction potential with a higher accuracy. 6. Based on results of the study it may be concluded that cracks of the foundations and dislocation of the structures at Hongseung earthquakes(Oct. 7, 1978, Richter scald 5.2) are not brought by the liquefaction process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.190-194
• /
• 2007

The forging process design and microstructure evolution for gas turbine disk of a Waspaloy is investigated in this study. Parameters related to deformation are die and preform geometry, and forging temperature of die and workpiece. Die and preform design are considered to reduce the forging load, and to avoid the forging defects. Blocker and finisher dies for multistage forging are designed and the initial billet geometry is determined. The control of hot forging parameters such as strain, strain rate and temperature also is important because the microstructure change in hot working affects the mechanical properties. The dynamic recrystallization evolution has been studied in the temperature range 900-$1200^{\circ}C$ and strain rate range 0.01-1.0s-1 using hot compression tests. Modeling equations are required represent the flow curve, recrystallized grain size, recrystallized volume fraction by various tests. In this study, we used to thermo-viscoplastic finite element modeling equation of DEFORM-2D to predict the microstructure change evolution during thermo-mechanical processing. The microstructure is updated during the entire thermal and deformation processes in forging.

• 전자공학회논문지B
• /
• 제31B권8호
• /
• pp.160-171
• /
• 1994

The wide dynamic range and severely attenuated contrast in mediastinal area appearing in typical chest radiographs have often caused difficulties in effective visualization and diagnosis of lung diseases. This paper proposes a new adaptive image enhancement technique which potentially solves this problem and there by improves observer performance through image processing. In the proposed method image processing is applied to the chest radiograph with different processing parameters for the lung field and mediastinum adaptively since there are much differences in anatomical and imaging properties between these two regions. To achieve this the chest radiograph is divided into the lung and mediastinum by gray level thresholding using the cumulative histogram and the dynamic range compression and local contrast enhancement are carried out selectively in the mediastinal region. Thereafter a gray scale transformation is performed considering the JND(just noticeable difference) characteristic for effective image displa. The processed images showed apparenty improved contrast in mediastinum and maintained moderate brightness in the lung field. No artifact could be observed. In the visibility evaluation experiment with 5 radiologists the processed images with better visibility was observed for the 5 important anatomical structures in the thorax.

• 소음진동
• /
• 제9권2호
• /
• pp.317-323
• /
• 1999

Dynamic characteristics of catenary that supplies electrical power to high-speed trains are investigated. A simple catenary is composed of the contact and messenger wires connected by droppers possessing bi-directional stiffness properties. For slender, repeating structures such as catenary, both the wave propagation and vibration properties need to be understood. The influence of parameters that determine catenary dynamics are investiaged through numerical simulations involving finite element models. The effects of the tension and flexural rigidity of the contact wire is first investigated. The effects of dropper characteristics are then investigated. For linear droppers wave propagation as well as modal properties are determined. For large catenary motion, droppers can be modeled as bi-directional elements possessing low stiffness in compression and high stiffness in tension. For this case, impulse response is computed and compared with the cases of linear droppers. It is found that the catenary dynamics are primarily determined by contact wire tension and dropper properties, with large responses observed in 5∼40 Hz frequency range. In particular, the dropper stiffness and spacing are found to have dominant influence on the response frequency and the wave transmission characteristics.

• 열처리공학회지
• /
• 제31권4호
• /
• pp.180-186
• /
• 2018

High temperature flow behaviors of Fe-Cr-Mo-V-W-C tool steel were investigated using isothermal compression tests on a Gleeble simulator. The compressive test temperature was varied from 850 to $1,150^{\circ}C$ with the strain rate ranges of 0.05 and $10s^{-1}$. The maximum height reduction was 45%. The dynamic softening related to the dynamic recrystallization was observed during hot deformation. The constitutive model based on Arrhenius-typed equation with the Zener-Hollomon parameter was proposed to simulate the hot deformation behavior of Fe-Cr-Mo-V-W-C steel. An artificial neural network (ANN) model was also developed to compare with the constitutive model. It was concluded that the ANN model showed more accurate prediction compared with the constitutive model for describing the hot compressive behavior of Fe-Cr-Mo-V-W-C steel.

• Structural Engineering and Mechanics
• /
• 제77권1호
• /
• pp.1-17
• /
• 2021

The influence of prestress force on the fundamental frequency and static deflection shape of uncracked Prestressed Concrete (PC) beams with a parabolic bonded tendon was examined in this paper. Due to the conflicts among existing theories, the analytical solutions for properly considering the dynamic and static behavior of these members is not straightforward. A series of experiments were conducted for a total period of approximately 2.5 months on a PC beam made with high strength concrete, subsequently and closely to the 28 days of age of concrete. Specifically, the simply supported PC member was short term subjected to free transverse vibration and three-point bending tests during its early-age. Subsequently, the experimental data were compared with a model that describes the dynamic behavior of PC girders as a combination of two substructures interconnected, i.e., a compressed Euler-Bernoulli beam and a tensioned parabolic cable. It was established that the fundamental frequency of uncracked PC beams with a parabolic bonded tendon is sensitive to the variation of the initial elastic modulus of concrete in the early-age curing. Furthermore, the small variation in experimental frequency with time makes doubtful its use in inverse problem identifications. Conversely, the relationship between prestress force and static deflection shape is well described by the magnification factor formula of the "compression-softening" theory by assuming the variation of the chord elastic modulus of concrete with time.

• Geomechanics and Engineering
• /
• 제29권6호
• /
• pp.627-643
• /
• 2022

Water-rock interactions have a significant influence on the mechanical behavior of rocks. In this study, uniaxial compression and tension tests on different water-treated sandstone samples were conducted. Acoustic emission (AE) monitoring and micro-pore structure detection were carried out. Water-rock interactions and their effects on rock mechanical behavior were discussed. The results indicate that water content significantly weakens rock mechanical strength. The sensitivity of the mechanical parameters to water treatment, from high to low, are Poisson ratio (𝜇), uniaxial tensile strength (UTS), uniaxial compressive strength (UCS), elastic modulus (E), and peak strain (𝜀). After water treatment, AE activities and the shear crack percentage are reduced, the angles between macro fractures and loading direction are minimized, the dynamic phenomenon during loading is weakened, and the failure mode changes from a mixed tensile-shear type to a tensile one. Due to the softening, lubrication, and water wedge effects in water-rock interactions, water content increases pore size, promotes crack development, and weakens micro-pore structures. Further damage of rocks in fractured and caved zones due to the water-rock interactions leads to an extra load on the adjoining coal and rock masses, which will increase the risk of dynamic disasters.

• 분석과학
• /
• 제9권2호
• /
• pp.179-191
• /
• 1996

초내열 718 합금의 고온 변형 거동을 이해하기 위하여 rotating grade의 718 합금을 이용하여 온도 $927{\sim}1066^{\circ}C$, 변형속도 $5{\times}10^{-4}{\sim}5{\times}10^0sec^{-1}$ 범위에서 진변형량 0.7까지 압축실험을 수행하였다. 최대 유동 응력은 변형 속도가 증가하고 시험 온도가 감소함에 따라 증가하였다. 변형 속도 $5{\times}10^{-1}sec^{-1}$을 제외한 대부분의 설험 조건에서 가공 연화현상이 관찰되었다. 가공 연화는 저온, 고변형 속도에서는 주로 동적 회복 및 변형 쌍정에 의해 일어나는 반면 고온, 저변형 속도 조건에서는 동적 재결정에 의해 발생하였으며 $5{\times}10^{-1}sec^{-1}$의 변형 속도 조건에서는 동적 재결정된 결정 입자들의 재가공 경화에 의해 가동 경화현상이 나타났다. 변형 속도 감도(m)는 변형 속도가 낮은 경우에는 0.3 정도로서 주로 동적 재결정에 의해 변형 거동이 나타남을 반영하였으며 고변형 속도에서는 0.1 정도로서 동적 회복과 변형 쌍정의 발생으로 718 합금의 변형이 이루어짐을 알 수 있었다.

• 한국방재학회 논문집
• /
• 제6권1호
• /
• pp.39-48
• /
• 2006

본 시험은 다양한 sine파형을 가진 인장 및 압축 하중 하에서 아스팔트 혼합물의 모듀율값 을 비교평가하기 위하여 수행되었다. 즉, 휴식시간을 가진 반복 인장 haversine 하중, 휴식시간을 가진 반복 압축 haversine 하중, 주기적 인장하중, 주기적 압축하중, 그리고 주기적 인장-압축 반복하중이라는 총 5개의 하중형태가 32, 50, 68, 86, $104^{\circ}F$ (0, 10, 20, 30, $40^{\circ}C$) 라는 5개의 온도하에서 평가되었다. 시험결과, 휴식시간을 가진 반복 haversine 하중으로 인한 아스팔트 콘크리트의 인장 및 압축 모듀율 값은 저온에서 유사한 값을 나타내었지만, 고온에서는 상이한 값을 보였다. 특히, 고온에서 압축 모듀율 값은 인장 모듀율 값보다 높은 수치를 보였다. 또한, 저온에서 일축 직접인장 시험으로부터 구한 모듀율 값은 간접 인장시험으로부터 구한 모듀율 값보다 높은 값을 나타내었다. 그러나, 고온에서는 서로 유사한 값을 보였다. 일반적으로, 휴식시간을 갖는 반복 haversine 하중을 이용하여 얻은 모듀율 값은 주기적 sine파형을 가진 하중으로부터 구한 모듀율 값보다 항상 낮은 값을 나타내었으며 그 두 가지 하중으로부터 구한 모듀율 값의 차이는 온도가 감소함에 따라 더욱 증가되었다.

• 지질공학
• /
• 제31권4호
• /
• pp.493-506
• /
• 2021

액상화 현상이란 지반이 포화된 느슨한 사질토 지반에 지진과 같은 동적하중이 급속히 작용할 때 과잉간극수압이 발생하고, 지반이 유효응력을 상실하고 액체화 되는 현상을 말한다. 액상화 평가를 위한 실내반복시험은 반복삼축압축시험과 반복전단시험을 통하여 확인이 가능하다. 이와 관련하여 본 연구에서는 반복삼축압축시험을 이용한 모래의 상대밀도와 입도분포에 따른 액상화 저항 강도를 확인하고자 하였고, 실험장비의 신뢰도 검증과 결과의 타당성을 확인하고자 기존의 선행연구와 대조하여 비교·분석하였다. 실험결과, 흙의 분류에 상관없이 상대밀도가 증가함에 따라 액상화 저항 강도가 높아짐을 확인하였고, 모래의 입도분포에 따른 액상화 저항강도는 SW에 가까운 SP시료의 액상화 저항강도가 상당히 높게 확인되었다. 또한 세립분 0% 대비 세립분 30%를 분석한 결과, 상대밀도 40~70%까지 증가함에 따라 액상화 저항강도가 5~20% 가까이 감소하였고, 국내 풍화토 지반이 주문진 표준사 대비 액상화 저항 강도가 세립분이 10%일 때는 30% 이상, 세립분이 30%일 때는 50% 이상 낮게 측정되었다.