• Journal of the Korean Geosynthetics Society
• /
• v.17 no.1
• /
• pp.75-83
• /
• 2018

This paper described a results of dynamic stability by using wheel tracking test and unconfined compression test, in order to evaluate behavior characteristics on the developed pocketable expansion material for emergency restoration of ground cavity. The wheel tracking test result showed that the settlement increment ratio of the recovered ground by the expansion material was decreased compared to the sandy ground in high load condition. That is, it was confirmed that the expansion material was able to restrain the settlement due to the material stiffness, and the same results were obtained for the dynamic stability evaluation results. From the results of unconfined compression test, the pocketable expansion material was found to be able to fully support load on the restored cavity.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.6 no.1
• /
• pp.23-33
• /
• 1994

Liquefaction characteristics of the reclaimed marine sand deposits is studied by means of the dynamic response analysis and the cyclic triaxial compression test. 1) From the result of the dynamic response analysis. it was found that the amplification of ground surface maximum acceleration varied with input earthquake motions and soil data, and earthquake coefficients were proposed to be applicable in evaluating liquefaction potential by simplified prediction methods. 2) For upper and soft sand deposits with small N-value, liquefaction strengths estimated by Seed and Idriss's simplified method were lower than those by the cyclic triaxial test while those by Iwasaki & Tatsuoka's or Vs-method were not lower. 3) Simplified methods were inclined to overestimate liquefaction potential in comparison with the dynamic response analysis and the cyclic triaxial compression test Allowable depths of liquefaction(safety factor 1) were estimated to be 7-14m for 0.1 -0.2g of input maximum acceleration.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.4 s.65
• /
• pp.379-388
• /
• 2003

The response of single story buildings and other case studies were investigated to observe trends and develop a better understanding of the impact of some design parameters on the seismic response of Concentrically Braced Frames (CBF). While many parameters are known to influence the behavior of braced frames, the focus of this study was mostly on quantifying energy dissipation in compression and its effectiveness on seismic performance. Based on dynamic analyses of single story braced frame and case studies, a bracing member designed with bigger R and larger KL/r was found to result in lower normalized cumulative energy ratio in both cases.

• Journal of Internet Computing and Services
• /
• v.8 no.3
• /
• pp.131-143
• /
• 2007

The current trends in information technology and intelligent systems use data mining techniques to discover patterns and extract rules from distributed databases. In distributed environment, the extracted rules from data mining techniques can be used in dynamic replications, adaptive load balancing and other schemes. However, transmission of large data through the system can cause errors and unreliable results. This paper proposes the intelligent distributed platform based on dynamic group binding using mobile agents which addresses the use of intelligence in distributed environment. The proposed grouping service implements classification scheme of objects. Data compressor agent and data miner agent extracts rules and compresses data, respectively, from the service node databases. The proposed algorithm performs preprocessing where it merges the less frequent dataset using neuro-fuzzy classifier before sending the data. Object group classification, data mining the service node database, data compression method, and rule extraction were simulated. Result of experiments in efficient data compression and reliable rule extraction shows that the proposed algorithm has better performance compared to other methods.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.72-72
• /
• 2018

A dynamic fatigue characteristic of dental implant system has been evaluated with applying single axial compressive shear loading based on the ISO 14801 standard. For the advanced dynamic fatigue test, multi-directional force and motion needed to be accompanied for more information of mechanical properties as based on mastication in oral environment. In this study, we have prepared loading and motion protocol for the multi-directional fatigue test of dental implant system with single (Apical/Occlusal; AO), and additional mastication motion (Lingual/Facial; LF, Mesial/Distal; MD). As following the prepared protocol (with modification of ISO 14801), fatigue test was conducted to verify the worst case results for the development of highly stabilized dental implant system. Mechanical testing was performed using an universal testing machine (MTS Bionix 858, MN, USA) for static compression and single directional loading fatigue, while the multi-directional loading was performed with joint simulator (ADL-Force 5, MA, USA) under load control. Basically, all mechanical test was performed according to the ISO 14801:2016 standard. Static compression test was performed to identify the maximum fracture force with loading speed of 1.0 mm/min. A dynamic fatigue test was performed with 40 % value of maximum fracture force and 5 Hz loading frequency. A single directional fatigue test was performed with only apical/occlusal (AO) force application, while multi directional fatigue tests were applied $2^{\circ}$ of facial/lingual (FL) or mesial/distal (MD) movement. Fatigue failure cycles were entirely different between applying single-directional loading and multi-directional loading. As a comparison of these loading factor, the failure cycle was around 5 times lower than single-directional loading while applied multi-directional loading. Also, the displacement change with accumulated multi-directional fatigue cycles was higher than that of single directional cycles.

• Wind and Structures
• /
• v.21 no.3
• /
• pp.353-367
• /
• 2015

As concrete wind-turbine towers are increasingly being used in wind-farm construction, there is a growing need to understand the behavior of concrete wind-turbine towers. In particular, experimental evaluations of concrete wind-turbine towers are necessary to demonstrate the dynamic characteristics and load-carrying capacity of such towers. This paper describes a model test of a prestressed concrete wind-turbine tower that examines the dynamic characteristics and load-carrying performance of the tower. Additionally, a numerical model is presented and used to verify the design approach. The test results indicate that the first natural frequency of the prestressed concrete wind turbine tower is 0.395 Hz which lies between frequencies 1P and 3P (0.25-0.51 Hz). The damper ratio is 3.3%. The maximum concrete compression stresses are less than the concrete design compression strength, the maximum tensile stresses are less than zero and the prestressed strand stresses are less than the design strength under both the serviceability and ultimate limit state loads. The maximum displacement of the tower top are 331 mm and 648 mm for the serviceability limit state and ultimate limit state, respectively, which is less than L/100 = 1000 mm. Compared with traditional tall wind-turbine steel towers, the prestressed concrete tower has better material damping properties, potential lower maintenance cost, and lower construction costs. Thus, the prestressed concrete wind-turbine tower could be an innovative engineering solution for multi-megawatt wind turbine towers, in particular those that are taller than 100 m.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.454-464
• /
• 1987

The objective of this research is to analyze and evaluate the dynamic flow curve of metals under impact loading at both high strain rate (.epsilon.=1/h dh/dt > 10$\^$3/m/s/m) and large strain (.epsilon.=In h/h$\_$0/ > 1.0). A test method for dynamic compression of metal disc is described. The velocity of the striker face and the force on the anvil are measured during the impact period. From these primitive data the axial stress, strain, and strain rate of the disc are obtained. The Strain rate is determined by the striker velocity divided by the specimen height. This gives a slightly increasing strain rate over most of the deformation period. Strain rates of 100 to 10,000 per second are achieved. Attainable final strains are 150%. A discussion of several problem areas is presented. The friction on the specimen surfaces, the determination of the frictional coefficient, the influence of the specimen geometry (h$\_$0//d$\_$0/ ratio) on the friction effect, the lock-up condition for a given configuration, the friction correction factor, and the evaluation of several lubricants are given. The flow function(stress verus strain) is dependent on the material condition(e.g., prior cold work), specimen geometry, strain rate, and temperature.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.16 no.3
• /
• pp.17-28
• /
• 2006

The appearance of variant malicious codes using obfuscation techniques is accelerating the spread of malicious codes around the detection by a vaccine. n a system does not patch detection patterns for vulnerabilities and worms to the vaccine, it can be infected by the worms and malicious codes can be spreaded rapidly to other systems and networks in a few minute. Moreover, It is limited to the conventional pattern based detection and treatment for variants or new malicious codes. In this paper, we propose a method of behavior based detection by the static analysis, the dynamic analysis and the dynamic monitoring to detect a malicious code using obfuscation techniques with the PE compression. Also we show that dynamic monitoring can detect worms with the PE compression which accesses to important resources such as a registry, a cpu, a memory and files with the proposed method for similarity.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.64-69
• /
• 2002

Dynamic analysis of laminated beams with a embedded damping layer under tension or compression axial load is investigated. Improved Layer-Wise Zig-Zag Beam Theory and Interdependent Kinematic Relation using the governing equations of motion are incorporated to model the laminated beams with a damping layer and a corresponding beam zig-zag finite element is developed. Flexural frequencies and modal loss factors under tension or compression axial load are calculated based on Complex Eigenvalue Method. The effects of the axial tension and compression load on the frequencies and loss factors are discussed.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.117.2-117.2
• /
• 2012

It is generally accepted that sudden compressions of the magnetosphere cause electromagnetic ion cyclotron (EMIC) wave growth by increasing the proton temperature anisotropy. These compression-associated EMIC waves are expected to be on higher latitudes (i.e., higher-L regions close to the magnetopause). In this study we examine Pc1 pulsations, which are believed to be generated by the EMIC instability, observed at subauroral latitude near the nominal plasmapause when the magnetosphere is suddenly compressed by solar wind dynamic pressure variations, using induction magnetometer data obtained from Athabasca, Canada (geomagnetic latitude = 61.7 N, L ~ 4.5). We identified 9 compression-associated Pc1 waves with frequencies of ~0.5-2.0 Hz. The wave activity appears in the horizontal H (positive north) and D (positive eastward) components. All of events show low coherence between H and D components. This indicates that the Pc1 pulsations in H and D oscillate with a different frequency. Thus, we cannot determine the polarization state of the waves. We will discuss the occurrence location of compression-associated Pc1 pulsations, their spectral structure, and wave properties.