• Journal of the Korea Convergence Society
• /
• v.7 no.1
• /
• pp.177-182
• /
• 2016

In order that the track vehicle utilized on the purpose of heavy industry and military affair may endure the vehicle body with heavy weight, the link surrounding the mobile wheel is affected with the great force by the load transferred at the vehicle body. This happened force gives rise to a decline in the durability throughout the track. In this paper, the models with the shapes of track pads in common use are designed and the model at which the wear of track pad and the damage of link can be decreased effectively is contrived. Also, by applying this study result to the design of track vehicle, it can contribute to the safe design for damage prevention and durability improvement. It is possible to be grafted onto the convergence technique at the designed factor of pad shape and show the esthetic sense.

• Journal of the Korean Institute of Gas
• /
• v.24 no.3
• /
• pp.47-53
• /
• 2020

In this study, the optimization design data was presented by analyzing the performance and durability of the cooling fan by one-way fluid-structure interaction analysis of the cooling fan shape used in the engine generator. For this purpose, a steady-state analysis was performed on the flow field inside the cooling fan, and the durability was analyzed by using the steady-state calculation results as input data for structural analysis. Six types were modeled for fluid analysis by changing the blade and sweep angle of the cooling fan, and the ratio of mass flow rate and torque was best in A type, but B type with relatively large mass flow rate was the best. It was judged to have flow performance. As a result of examining the structural analysis by setting the four blade thickness of the B type selected through the fluid analysis, it was judged that B Type-3 is the most suitable when considering the fatigue safety factor.

• Journal of the Korea Concrete Institute
• /
• v.28 no.1
• /
• pp.49-57
• /
• 2016

The aim of this study was to investigate the fundamental properties of pyroclastic flow deposit (PFD), and evaluate the fresh and strength properties of concrete mixed with PFD by indoor tests. The fresh properties, strength properties, shrinkage properties, and durability of the concrete mixed with PFD were also evaluated by outdoor plant tests. the harmful alkali-silica reaction did not occur by mixing concrete with PFD. ages. Moreover, no difficulty was found to be associated with concrete manufacture in the plant because no change in air contents and noticeable slump loss occurred by mixing concrete with PFD. The strength properties, shrinkage properties, and durability of the concrete mixed with PFD were also compared with those of normal concrete. With a suitable temperature control and curing method of concrete, the concrete mixed with PFD is considered to be useful in the construction material field.

• Journal of Korean Society of Rural Planning
• /
• v.19 no.4
• /
• pp.307-317
• /
• 2013

The value and functionality of boundary barriers in rural villages have been neglected in the aspects as the buffer zone(boundary barrier) that links between the inside space(housing site) and the outside space(road). On this understanding, this study evaluated conservation value, economical efficiency and durability by the types and materials of the boundary barriers in rural village through Multi-attribute Decision Making. By applying to the current situations of boundary barriers on total 21 case study villages, each factor value was measured. And using Matrix Analysis Technique, the boundary barriers are classified into 4 types and the improvement ways for each type were proposed. As a result, the durability of boundary barriers in rural villages showed similarity value(more than 0.85 out of 1). But economical efficiency of those was low(less than 0.5 out of 1) and those functionalities were very lacking(about 0.3 out of 1). In the conclusion, the maintenance of boundary barriers in rural villages requires the policy that is able to complement conservation value and economical efficiency and is proper to the characteristic of each village. These renewable policies would contribute to the increase of the value of rural amenity as well as creation of economical and social value.

• Journal of the Korea Convergence Society
• /
• v.8 no.7
• /
• pp.219-224
• /
• 2017

This paper investigates equivalent stress and deformation happening at inner fiber structure when the tensile force acts on the specimen with arch type composed of carbon fiber. The countless many each fiber is applied on the unidirectional axis at CFRP and has the high specific strength and stiffness by comparing with iron. In this study, the distribution of stress due to radius is investigated at the structure of arch type composed with the optimum stacking angle of $60^{\circ}$. And the durability is seen to be lower as the radius increases at the same stacking angle. By applying the result of this study to the design of structure with arch type, it can be devoted to the safe design for the prevention of damage and the durabilty improvement. And it is possible to be grafted onto the convergence technique at the designed factor and show the esthetic sense.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.541-544
• /
• 2008

Recently, a variety of researches has been carried out to estimate the reliability-based analysis and design method of concrete structures and is attracted by probabilistic-based durability analysis/method of concrete structures subjected to chloride containing environment using MCS (Monte Carlo Simulation). Probabilistic-based durability analysis/method was proposed by lots of researches, but there is the lack of data for degradation factors for the calculation of probability distribution. The reliability based durability analysis method represents that the service life and reliability index varies with the probability distribution and coefficient of variation of each factor. Therefore, in this paper, the importance of experiment data for the degradation factors is confirmed and the study of reliability index in RC structures under chloride attack environments is performed considering the variation coefficient of degradation factors.

• Journal of the Korea Institute of Building Construction
• /
• v.6 no.2 s.20
• /
• pp.73-79
• /
• 2006

The purpose of this study is to enhance the development of construction waste-recycling technologies and its economical efficiency by developing environment-friendly tetrapod, precast concrete, where recycled aggregate is used in order to promote recycling of waste concrete. The results of concrete mechanic characteristics experiments by the circulation coarse aggregate-replacement ratio are as the following. The circulation aggregate is lower and higher than natural aggregate in specific gravity and absorption ratio, respectively so that in case of mix proportioning, unit volume increases, while unit aggregate amount decreases. From the result, sufficient experiments of physical characteristics of circulation aggregate are required to get proper mix proportioning. When circulation aggregate-replacement ratio increases, compressive strength tends to decrease comprehensively, but 50% of replacement ratio is good enough to use. When circulation coarse aggregate's replacement ratio is 0%, drying shrinkage, which causes cracks in concrete and deteriorates durability, shows the minimum length change and the higher the ratio, the larger the length change. Thus. when using circulation coarse aggregate, drying shrinkage should be fairly examined. In freezing-and-thawing resistance, weight loss tends to comprehensively increase its loss at the circulation aggregate-mixed site. And the examination of surface aggregate-omission ratio is further needed and dynamic elastic modulus and durability factor(DF) require more study as well. In order to use circulation aggregate to tetrapod, a clear standard for strength should be first prepared and at the same time, more study about durability is needed.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.3
• /
• pp.163-170
• /
• 2019

Durability of instrument is one of the most important factor to ensure accurate treatment and decrease failure for the orthopedic surgical operation. Normally, a set-screw driver tip has been processed with hard coating for their higher durability and wear resistance. And several surface modification methods were obtained such as titanium nitride (TiN) coating, diamond like carbon coating, other nitriding, and etc. In this study, we have surface modified on set-screw driver tip with TiN and DLC, investigated whether the TiN and DLC coatings affect the mechanical properties and durability of the set-screw driver tip in the pedicle screw system. The surface morphologies were observed with scanning-electron microscopy (SEM), and the static/dynamic torsional properties were investigated with universal testing machine based on ASTM F543. Coating thickness of each coatings were commonly around $1^{\circ}C$. Static torsional stiffness, and ultimate torque values for DLC and TiN coated samples were significantly higher than those of non-coated sample by the pared T-test. Surface morphology of after the dynamic torsional test was more clean with less scratch or friction traces from DLC coating than that of TiN coating and non-coated sample.

• Advances in concrete construction
• /
• v.11 no.5
• /
• pp.419-428
• /
• 2021

The pH of cement-based materials (CBMs) is an important factor for their durability, sustainability, and long service life. Currently, the use of supplementary cementitious materials (SCMs) is becoming mandatory due to economic, environmental, and sustainable issues. There is a decreasing trend in pH of CBMs due to incorporation of SCMs. The determination of numerical values of pH is very important for various low and high volume SCMs blended cement mortars for the better understanding of different defects and durability issues during their service life. In addition, the effect of cement hydration and pozzolanic reaction of SCMs on the pH should be determined at initial and later ages. In this study, the effect of low and high-volume fly ash (FA) and ground granulated ballast furnace slag (GGBFS) cement mortars in different curing conditions on their pH values has been determined. Thermal gravimetric analysis (TGA) was carried out to support the findings from pH measurements. In addition, thermal conductivity (k-value) and strength activity indices of these cement mortars were discussed. The results showed that pH values of all blended cement mortars were less than ordinary Portland cement (OPC) mortar in all curing conditions used. There was a decreasing tendency in pH of all mortars with passage of time. In addition, the pH of cement mortars was not only dependent on the quantity of Ca(OH)₂. The effect of adding SCMs on the pH value of cement mortar should be monitored and measured for both short and long terms.

• Structural Engineering and Mechanics
• /
• v.80 no.5
• /
• pp.491-501
• /
• 2021

A difference in subgrade settlement between two rails of a track manifests as lateral differential subgrade settlement. This settlement causes unsteadiness in the motion of trains passing through the corresponding area. To illustrate the effect of lateral differential subgrade settlement on the dynamic response of a vehicle-track coupling system, a three-dimensional vehicle-track-subgrade coupling model was formulated by combining the vehicle-track dynamics theory and the finite element method. The wheel/rail force, car body acceleration, and derailment factor are chosen as evaluation indices of the system dynamic response. The effects of the amplitude and wavelength of lateral differential subgrade settlement as well as the driving speed of the vehicle are analyzed. The study reveals the following: The dynamic responses of the vehicle-track system generally increase linearly with the driving speed when the train passes through a lateral subgrade settlement area. The wheel/rail force acting on a rail with a large settlement exceeds that on a rail with a small settlement. The dynamic responses of the vehicle-track system increase with the amplitude of the lateral differential subgrade settlement. For a 250-km/h train speed, the proposed maximum amplitude for a lateral differential settlement with a wavelength of 20 m is 10 mm. The dynamic responses of the vehicle-track system decrease with an increase in the wavelength of the lateral differential subgrade settlement. To achieve a good operation quality of a train at a 250-km/h driving speed, the wavelength of a lateral differential subgrade settlement with an amplitude of 20 mm should not be less than 15 m. Monitoring lateral differential settlements should be given more emphasis in routine high-speed railway maintenance and repairs.