• 제목/요약/키워드: Dump Surface

검색결과 34건 처리시간 0.021초

임기광산 폐석적치장의 수리침투특성 분석

  • 지상우;정영욱;임길재
    • 한국지하수토양환경학회:학술대회논문집
    • /
    • 한국지하수토양환경학회 2004년도 임시총회 및 추계학술발표회
    • /
    • pp.394-398
    • /
    • 2004
  • This study was carried out to plan the prevention of the generation and discharge of acid mine drainage (AMD). Hydraulic characteristics were tested with the disk tension infiltrometer around the waste rock dump of the Imgi abandoned pyrophyllite mine in Busan, Korea. Because the waste rock dump of the Imgi mine have very low infiltration rate, most of rain was expected flowing into adjoined stream through the slope or plane as surface flow rather then throughflow or ground water. But slopes of the waste rock dump have many 'V' type erosion gullies and consist multi-layers. These gullies and multi-layers have coarse clastic particle layer which have very large hydraulic conductivity. So through these coarse clastic particle layers a large part of rain flow into ground. And also these layers could be played a function of aeration path, which induced oxidation of sulfide minerals and generation of AMD continuously.tinuously.

  • PDF

예막 공기충돌형 분사기의 벤추리 덤프면 설계 (Design of Venturi Dump Surface for Pre-filming Airblast Injector)

  • 신동수;최명환;;구자예;정승채
    • 한국추진공학회지
    • /
    • 제22권4호
    • /
    • pp.44-54
    • /
    • 2018
  • 예막 공기충돌형 방식의 희박 예혼합 예증발(LPP) 보조 분사기에 벤추리를 장착하여 분무 실험을 할 경우 액적의 낙수현상이 나타나며, 이는 액적의 불균일한 분포로 나타난다. 이를 해결하기 위해 벤추리의 출구 각도를 변화시켜 노즐목 부분에서 덤프면을 형성시켰다. 덤프면의 형성은 벤추리 출구에 재순환영역을 형성시키면서 미립화 성능을 개선하며 액적 낙수를 최소화하였다. 분사기의 불균일한 분무를 해결하기 위해 벤추리 내부의 유동 특성 및 분무의 SMD를 비교분석하였으며, 최종적으로 분무의 손실을 최소로 하며 분무를 향상시킬 수 있는 최적의 벤추리의 형상을 선정하였다.

Design and fabrication of beam dumps at the µSR facility of RAON for high-energy proton absorption

  • Jae Chang Kim;Jae Young Jeong;Kihong Pak;Yong Hyun Kim;Junesic Park;Ju Hahn Lee;Yong Kyun Kim
    • Nuclear Engineering and Technology
    • /
    • 제55권10호
    • /
    • pp.3692-3699
    • /
    • 2023
  • The Rare isotope Accelerator complex for ON-line experiments in Korea houses several accelerator complexes. Among them, the µSR facility will be initially equipped with a 600 MeV and 100 kW proton beam to generate surface muons, and will be upgraded to 400 kW with the same energy. Accelerated proton beams lose approximately 20% of the power at the target, and the remaining power is concentrated in the beam direction. Therefore, to ensure safe operation of the facility, concentrated protons must be distributed and absorbed at the beam dump. Additionally, effective dose levels must be lower than the legal standard, and the beam dumps used at 100 kW should be reused at 400 kW to minimize the generation of radioactive waste. In this study, we introduce a tailored method for designing beam dumps based on the characteristics of the µSR facility. To optimize the geometry, the absorbed power and effective dose were calculated using the MCNP6 code. The temperature and stress were determined using the ANSYS Mechanical code. Thus, the beam dump design consists of six structures when operated at 100 kW, and a 400 kW beam dump consisting of 24 structures was developed by reusing the 100 kW beam dump.

강우시 광산폐기물 적치사면의 침투 및 안정성에 대한 수치해석 (Numerical Analysis of the Seepage from and Stability of a Mine Waste-dump Slope during Rainfall)

  • 송영석
    • 지질공학
    • /
    • 제25권1호
    • /
    • pp.57-66
    • /
    • 2015
  • 부산 임기광산의 광산폐기물 적치사면을 대상으로 강우에 따른 사면의 침투해석과 안정해석을 연계하여 수행하였다. 광산폐기물 적치사면의 경사는 40-45°로써 비교적 급한 편이고, 암반층 상부의 광산폐기물은 약 7-8 m의 두께로 존재하며, 지하수위는 지표면으로부터 약 6.6 m 깊이에 위치하고 있다. 현장에서 채취한 시료를 대상으로 각종 실내시험을 수행하여 강우 시 침투거동 및 사면안정해석을 위한 입력자료를 선정하였다. SEEP/W를 이용하여 다양한 강우강도 조건에서 침투해석을 수행한 결과 강우지속시간이 길어짐에 따라 습윤전선은 하강함을 알 수 있다. 강우강도가 50 mm/hr 이상 이고 강우지속시간이 24시간 이상인 경우 침윤전선은 사면의 하단부에서 지하수위와 만나게 되므로 토층 전체가 포화됨을 알 수 있다. 침투해석결과를 연동하여 SLOPE/W를 이용하여 사면안정해석을 수행한 결과 강우침투로 인한 침윤전선이 하강함에 따라 사면안전율은 낮아짐을 알 수 있다. 강우가 5-6시간 지속적으로 발생된 이후 사면안전율은 급격하게 낮아지며, 이후 사면안전율이 미소하게 회복되다가 수렴한다. 사면안전율이 급격하게 낮아지는 이유는 강우로 인한 임계 활동면과 침윤전선의 깊이가 유사하여 해당깊이까지 간극수압이 증가되고 모관흡수력이 감소되었기 때문이다.

Study on slope stability of waste dump with a weak layer using finite element limit analysis method

  • Chong Chen;Huayong Lv;Jianjian Zhao;Zhanbo Cheng;Huaiyuan Wang;Gao Xu
    • Structural Engineering and Mechanics
    • /
    • 제89권3호
    • /
    • pp.253-263
    • /
    • 2024
  • Slope stability is generally paid more attention to in slope protection works, especially for slope containing weak layers. Two indexes of safety factor and failure model are selected to perform slope stability. Moreover, the finite element limit analysis method comprehensively combines the advantage of the limit analysis method and the finite element method obtaining the upper and lower bounds of the safety factor and the failure mode under the slope stability limit state. In this study, taking a waste dump containing a weak layer as an engineering background, the finite element limit analysis method is adopted to explore the potential failure mode. Meanwhile, the sensitivity analysis of slope stability is performed on geometrical and geotechnical parameters of the waste dump. The results show that the failure mode of the waste dump slope is two wedges if the weak layer is located on the ground surface (Model A), while the slope can be observed as three wedges failure if the weak layer is below the ground surface (Model B). In addition, both failure modes are highly sensitive to the friction angle of the weak layer and the shear strength of waste disposal, and moderately sensitive to the heap height, the dip angle and cohesion of the weak layer, while the toe cutting has limited effect on the slope stability. Moreover, the sensitivity to the excavation of the ground depends on the location of the weak layer and failure mode.

광산폐기물 적치사면의 불포화 특성변화 모니터링 시스템 구축 (Establishment on the Monitoring System for Unsaturated Characteristics Variation in a Mine Waste-Dump Slope)

  • 송영석;정인근
    • 한국지반신소재학회논문집
    • /
    • 제15권3호
    • /
    • pp.49-55
    • /
    • 2016
  • 본 연구에서는 부산 임기광산 광산폐기물 사면을 대상으로 강우 침투에 따른 지반내 불포화 특성변화를 살펴보기 위하여 불포화토 특성변화 측정유닛 및 시스템을 현장에 설치하였다. 불포화토 특성변화 측정시스템은 각종 측정유닛으로부터 측정된 자료를 저장, 관리 및 전달하는 시스템으로 Data Acquisition System(DAS), Solar System 및 불포화토 특성변화 측정유닛으로 구성되어 있다. 현장에 설치된 각종 측정유닛으로부터 측정된 강우, 체적함수비, 모관흡수력 등의 자료를 정리하여 분석하였다. 이들 결과를 살펴보면 강우시 체적함수비와 모관흡수력의 변화는 강우강도에 의해 크게 영향을 받으며, 강우시와 건기시 지표면 부근에서 가장 크게 증가하였다가 감소하는 것으로 나타났다. 그리고 현장에서 측정된 모관흡수력은 5-35kPa, 체적함수비는 0.12-0.24 범위에 존재하는 것으로 나타났다. 그러나 지하수위는 강우발생 직후 바로 증가하는 것이 아니라 2-3일의 시간이 경과한 뒤 증가함을 알 수 있다.

운반작업의 영향요소분석을 통한 덤프트럭의 운반속도 산정방법에 관한 연구 (A Study on the Estimating of the Dump Truck's Travel Speed Based on Analysis of Factors Affecting Earthmoving Operation)

  • 박현용;태용호;우성권
    • 한국건설관리학회논문집
    • /
    • 제8권3호
    • /
    • pp.97-105
    • /
    • 2007
  • 댐, 고속도로, 공항, 플랜트, 빌딩, 상하수도 처리장과 같은 많은 건설공사의 운반 작업이라 함은 프로젝트의 요구조건에 맞게 지면의 형상과 조건을 변형시키기 위하여 일정량의 토사를 운반하는 작업을 의미하며 흙 운반 작업의 정확한 이동시간의 계산은 작업의 생산성을 결정하고 궁극적으로 작업을 수행함에 있어 비용 효과적 인 장비배치를 위해 필수적인 요소라 할 수 있다. 그리고 덤프트럭을 활용한 운반 작업은 설계가 대비 평균 6%의 비용을 차지하고 있어 덤프트럭을 이용한 운반 작업은 공사비 관리 측면에서 중요한 비용 인자로 구분되어 관리해야 할 것이다. 따라서 본 연구에서는 현재 공사가 진행 중인 현장의 덤프트럭 주행속도의 자료 수집을 통하여 각 도로유형별 주행 속도에 영향을 미치는 요소를 파악하고 해당 도로유형별 영향요소를 고려한 도로유형 별 적정 주행 속도 산정에 관한 방법을 제시하고자 한다.

현장 모니터링 결과를 이용한 광미 적치사면 안정성의 수치해석적 연구 (Numerical Analysis of the Stability of a Tailings Dump Slope using Field Monitoring Results)

  • 송영석
    • 지질공학
    • /
    • 제27권1호
    • /
    • pp.21-29
    • /
    • 2017
  • 광미 적치사면에서 측정된 모니터링 결과와 현장조건을 고려한 수치해석결과를 이용하여 강우시 불포화 토층내 모관흡수력변화를 비교하고 이를 토대로 사면안정해석을 수행하였다. 이를 위하여 계측기간 동안 강우강도가 가장 크게 발생된 기간(72시간)을 선정하고, 대상기간 동안의 모관흡수력과 강우자료를 분석하였다. 그리고 현장에서 측정된 강우자료를 적용하여 침투 및 사면안정해석을 수행하였다. 강우에 따른 사면내 침투거동을 해석하기 위하여 SEEP/W를 활용하고 사면내 침투깊이를 고려한 사면안정해석을 위하여 SLOPE/W를 활용하였다. 먼저 현장에서 측정된 강우자료를 적용하여 SEEP/W를 이용한 침투해석을 수행하였다. 침투해석으로 계산된 모관흡수력과 현장계측으로 측정된 모관흡수력을 비교한 결과 모관흡수력의 크기에서는 다소 차이가 있으나 시간에 따른 변화양상은 유사한 것으로 나타났다. 그리고 침투해석결과와 연동하여 SLOPE/W를 이용한 사면안정해석을 수행한 결과 강우강도가 급속하게 증가되는 시점에서 사면안전율은 크게 감소하였으며, 이후 강우가 발생되지 않는 경우 사면안전율이 회복되는 것으로 해석되었다.

익산 제석사지 폐기유적 벽체 및 기와의 피열특성 (Scientific Analysis of Firing Characteristics for Walls and Rooftiles Excavated from Jeseoksa Dump-site, Iksan)

  • 안경숙;이민혜;한민수
    • 보존과학회지
    • /
    • 제37권5호
    • /
    • pp.567-578
    • /
    • 2021
  • 본 연구는 제석사지 폐기유적에서 출토된 벽체 및 기와 편 21점의 물리화학적 특성을 확인하고, 소성 온도를 추정함으로써 문헌 기록상으로 확인되는 화재로 인한 피열 가능성을 확인하였다. 분석 결과, 기와는 수비된 재료를 사용하였고, 벽체는 층위에 따라 서로 다른 입도의 재료를 사용하여 제작한 것으로 추정된다. 과소성된 시료의 경우, 일반적인 기와나 벽체와 달리 단면에 블로팅(bloating) 현상과 함께 고르지 못한 표면을 가지며, 일부분이 검게 그을린 것을 보아 일정한 소성 환경에서 제어된 상태로 고른 소성이 이루어지지 않은 것으로 판단된다. 또한 소성온도 추정 결과, 과소성되지 않은 기와는 900℃ 이하의 소성온도를 가졌으나 과소성된 시료는 1000℃ 이상의 열을 받았던 것으로 보이며, 당시 기와의 제작 온도보다 고온으로 소성되었음 보여준다. 또한, 불량품기와는 제작 당시 소성이나 성형 과정에서 불량품이 된 것으로 보이지만 과소성된 기와의 경우에 온전한 기와 형태를 가지면서 과피열 양상을 보여 화재로 인한 피열 가능성을 보여준다. 이러한 결과들을 종합적으로 고찰하였을 때, 익산 제석사지 폐기유적은 기록상 존재하는 화재로 인해 폐기된 건축 부재를 보관하던 장소였던 것으로 추정된다.

MTV를 적용한 아스팔트 포설에서 열분리 저감 효과 (Effect of Thermal Segregation Reduction in Asphalt Paving with MTV)

  • 권기철
    • 한국도로학회논문집
    • /
    • 제20권4호
    • /
    • pp.1-6
    • /
    • 2018
  • PURPOSES : The objective of this study is to evaluate of the effect of thermal segregation reduction in asphalt paving using material transfer vehicles (MTVs). METHODS : Asphalt paving using MTVs was carried out, and the paved surface temperature was measured using an infrared camera. The amount of thermal segregation was estimated from temperature variations. RESULTS : The transportation of hot mix asphalt (HMA) using dump trucks caused temperature segregation that persisted in the paving surface if an MTV was not used. The average temperature variation was 8.58% in paved surfaces where an MTV was not used. However, the temperature variation was 3.10%, 2.86%, and 4.53% for the base layer, inter-layer, and surface layer, respectively, when an MTV was used. CONCLUSIONS : The use of an MTV in asphalt paving reduces thermal segregation approximately 2.3 times in an asphalt mat via a remixing process and also allows for a smoother work process because the paver never needs to stop to receive HMA. However, MTV equipment without pre-heating devices requires careful temperature control during the warm up process at the MTV during construction in the winter.